From: Oded Gabbay <oded.gabbay@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: gregkh@linuxfoundation.org, Omer Shpigelman <oshpigelman@habana.ai>
Subject: [PATCH 1/2] habanalabs: halt debug engines on user process close
Date: Sun, 5 May 2019 00:57:32 +0300 [thread overview]
Message-ID: <20190504215733.12823-1-oded.gabbay@gmail.com> (raw)
From: Omer Shpigelman <oshpigelman@habana.ai>
This patch fix a potential bug where a user's process has closed
unexpectedly without disabling the debug engines. In that case, the debug
engines might continue running but because the user's MMU mappings are
going away, we will get page fault errors.
This behavior is also opposed to the general rule where nothing runs on
the device after the user process closes.
The patch stops the debug H/W engines upon process termination and thus
makes sure nothing runs on the device after the process goes away.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
---
drivers/misc/habanalabs/context.c | 6 ++++++
drivers/misc/habanalabs/goya/goya.c | 3 ++-
drivers/misc/habanalabs/goya/goyaP.h | 1 +
drivers/misc/habanalabs/goya/goya_coresight.c | 17 +++++++++++++++++
drivers/misc/habanalabs/habanalabs.h | 2 ++
5 files changed, 28 insertions(+), 1 deletion(-)
diff --git a/drivers/misc/habanalabs/context.c b/drivers/misc/habanalabs/context.c
index 4804cdcf4c48..f4c92f110a72 100644
--- a/drivers/misc/habanalabs/context.c
+++ b/drivers/misc/habanalabs/context.c
@@ -26,6 +26,12 @@ static void hl_ctx_fini(struct hl_ctx *ctx)
dma_fence_put(ctx->cs_pending[i]);
if (ctx->asid != HL_KERNEL_ASID_ID) {
+ /*
+ * The engines are stopped as there is no executing CS, but the
+ * Coresight might be still working by accessing addresses
+ * related to the stopped engines. Hence stop it explicitly.
+ */
+ hdev->asic_funcs->halt_coresight(hdev);
hl_vm_ctx_fini(ctx);
hl_asid_free(hdev, ctx->asid);
}
diff --git a/drivers/misc/habanalabs/goya/goya.c b/drivers/misc/habanalabs/goya/goya.c
index a582e29c1ee4..02d116b01a1a 100644
--- a/drivers/misc/habanalabs/goya/goya.c
+++ b/drivers/misc/habanalabs/goya/goya.c
@@ -4819,7 +4819,8 @@ static const struct hl_asic_funcs goya_funcs = {
.set_dram_bar_base = goya_set_ddr_bar_base,
.init_iatu = goya_init_iatu,
.rreg = hl_rreg,
- .wreg = hl_wreg
+ .wreg = hl_wreg,
+ .halt_coresight = goya_halt_coresight
};
/*
diff --git a/drivers/misc/habanalabs/goya/goyaP.h b/drivers/misc/habanalabs/goya/goyaP.h
index 14e216cb3668..c83cab0d641e 100644
--- a/drivers/misc/habanalabs/goya/goyaP.h
+++ b/drivers/misc/habanalabs/goya/goyaP.h
@@ -202,6 +202,7 @@ void goya_add_device_attr(struct hl_device *hdev,
struct attribute_group *dev_attr_grp);
int goya_armcp_info_get(struct hl_device *hdev);
int goya_debug_coresight(struct hl_device *hdev, void *data);
+void goya_halt_coresight(struct hl_device *hdev);
void goya_mmu_prepare(struct hl_device *hdev, u32 asid);
int goya_mmu_clear_pgt_range(struct hl_device *hdev);
diff --git a/drivers/misc/habanalabs/goya/goya_coresight.c b/drivers/misc/habanalabs/goya/goya_coresight.c
index 1ac951f52d1e..49b5efb3a912 100644
--- a/drivers/misc/habanalabs/goya/goya_coresight.c
+++ b/drivers/misc/habanalabs/goya/goya_coresight.c
@@ -626,3 +626,20 @@ int goya_debug_coresight(struct hl_device *hdev, void *data)
return rc;
}
+
+void goya_halt_coresight(struct hl_device *hdev)
+{
+ struct hl_debug_params params = {0};
+ int i, rc;
+
+ for (i = GOYA_ETF_FIRST ; i <= GOYA_ETF_LAST ; i++) {
+ params.reg_idx = i;
+ rc = goya_config_etf(hdev, ¶ms);
+ if (rc)
+ dev_err(hdev->dev, "halt ETF failed, %d/%d\n", rc, i);
+ }
+
+ rc = goya_config_etr(hdev, ¶ms);
+ if (rc)
+ dev_err(hdev->dev, "halt ETR failed, %d\n", rc);
+}
diff --git a/drivers/misc/habanalabs/habanalabs.h b/drivers/misc/habanalabs/habanalabs.h
index 71243b319920..adef7d9d7488 100644
--- a/drivers/misc/habanalabs/habanalabs.h
+++ b/drivers/misc/habanalabs/habanalabs.h
@@ -501,6 +501,7 @@ enum hl_pll_frequency {
* @init_iatu: Initialize the iATU unit inside the PCI controller.
* @rreg: Read a register. Needed for simulator support.
* @wreg: Write a register. Needed for simulator support.
+ * @halt_coresight: stop the ETF and ETR traces.
*/
struct hl_asic_funcs {
int (*early_init)(struct hl_device *hdev);
@@ -578,6 +579,7 @@ struct hl_asic_funcs {
int (*init_iatu)(struct hl_device *hdev);
u32 (*rreg)(struct hl_device *hdev, u32 reg);
void (*wreg)(struct hl_device *hdev, u32 reg, u32 val);
+ void (*halt_coresight)(struct hl_device *hdev);
};
--
2.17.1
next reply other threads:[~2019-05-04 21:57 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-04 21:57 Oded Gabbay [this message]
2019-05-04 21:57 ` [PATCH 2/2] uapi/habanalabs: add opcode for enable/disable device debug mode Oded Gabbay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190504215733.12823-1-oded.gabbay@gmail.com \
--to=oded.gabbay@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=oshpigelman@habana.ai \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox