Re: [net-next,v4 2/2] net: phy: sfp: enable i2c-bus detection on ACPI based systems

Russell King - ARM Linux admin
2019-05-29T09:51:49Z

On Tue, May 28, 2019 at 04:02:33PM -0700, Ruslan Babayev wrote:
> Lookup I2C adapter using the "i2c-bus" device property on ACPI based
> systems similar to how it's done with DT.
>
> An example DSD describing an SFP on an ACPI based system:
>
> Device (SFP0)
> {
> Name (_HID, "PRP0001")
> Name (_CRS, ResourceTemplate()
> {
> GpioIo(Exclusive, PullDefault, 0, 0, IoRestrictionNone,
> "\\_SB.PCI0.RP01.GPIO", 0, ResourceConsumer)
> { 0, 1, 2, 3, 4 }
> })
> Name (_DSD, Package ()
> {
> ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
> Package () {
> Package () { "compatible", "sff,sfp" },
> Package () { "i2c-bus", \_SB.PCI0.RP01.I2C.MUX.CH0 },
> Package () { "maximum-power-milliwatt", 1000 },
> Package () { "tx-disable-gpios", Package () { ^SFP0, 0, 0, 1} },
> Package () { "reset-gpio", Package () { ^SFP0, 0, 1, 1} },
> Package () { "mod-def0-gpios", Package () { ^SFP0, 0, 2, 1} },
> Package () { "tx-fault-gpios", Package () { ^SFP0, 0, 3, 0} },
> Package () { "los-gpios", Package () { ^SFP0, 0, 4, 1} },
> },
> })
> }
>
> Device (PHY0)
> {
> Name (_HID, "PRP0001")
> Name (_DSD, Package ()
> {
> ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
> Package () {
> Package () { "compatible", "ethernet-phy-ieee802.3-c45" },
> Package () { "sfp", \_SB.PCI0.RP01.SFP0 },
> Package () { "managed", "in-band-status" },
> Package () { "phy-mode", "sgmii" },
> },
> })
> }
>
> Signed-off-by: Ruslan Babayev <ruslan@babayev.com>
> Cc: xe-linux-external@cisco.com

This looks fine now, thanks.

Acked-by: Russell King <rmk+kernel@armlinux.org.uk>

> ---
> drivers/net/phy/sfp.c | 35 +++++++++++++++++++++++++++--------
> 1 file changed, 27 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c
> index d4635c2178d1..554acc869c25 100644
> --- a/drivers/net/phy/sfp.c
> +++ b/drivers/net/phy/sfp.c
> @@ -1,4 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0
> +#include <linux/acpi.h>
> #include <linux/ctype.h>
> #include <linux/delay.h>
> #include <linux/gpio/consumer.h>
> @@ -1782,6 +1783,7 @@ static void sfp_cleanup(void *data)
> static int sfp_probe(struct platform_device *pdev)
> {
> const struct sff_data *sff;
> + struct i2c_adapter *i2c;
> struct sfp *sfp;
> bool poll = false;
> int irq, err, i;
> @@ -1801,7 +1803,6 @@ static int sfp_probe(struct platform_device *pdev)
> if (pdev->dev.of_node) {
> struct device_node *node = pdev->dev.of_node;
> const struct of_device_id *id;
> - struct i2c_adapter *i2c;
> struct device_node *np;
>
> id = of_match_node(sfp_of_match, node);
> @@ -1818,14 +1819,32 @@ static int sfp_probe(struct platform_device *pdev)
>
> i2c = of_find_i2c_adapter_by_node(np);
> of_node_put(np);
> - if (!i2c)
> - return -EPROBE_DEFER;
> -
> - err = sfp_i2c_configure(sfp, i2c);
> - if (err < 0) {
> - i2c_put_adapter(i2c);
> - return err;
> + } else if (has_acpi_companion(&pdev->dev)) {
> + struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
> + struct fwnode_handle *fw = acpi_fwnode_handle(adev);
> + struct fwnode_reference_args args;
> + struct acpi_handle *acpi_handle;
> + int ret;
> +
> + ret = acpi_node_get_property_reference(fw, "i2c-bus", 0, &args);
> + if (ACPI_FAILURE(ret) || !is_acpi_device_node(args.fwnode)) {
> + dev_err(&pdev->dev, "missing 'i2c-bus' property\n");
> + return -ENODEV;
> }
> +
> + acpi_handle = ACPI_HANDLE_FWNODE(args.fwnode);
> + i2c = i2c_acpi_find_adapter_by_handle(acpi_handle);
> + } else {
> + return -EINVAL;
> + }
> +
> + if (!i2c)
> + return -EPROBE_DEFER;
> +
> + err = sfp_i2c_configure(sfp, i2c);
> + if (err < 0) {
> + i2c_put_adapter(i2c);
> + return err;
> }
>
> for (i = 0; i < GPIO_MAX; i++)
> --
> 2.19.2
>
>

--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up