[PATCH 1/3] ath10k: snoc: skip regulator operations

Bjorn Andersson
2019-07-25T17:48:18Z

The regulator operations is trying to set a voltage to a fixed value, by
giving some wiggle room. But some board designs specifies regulator
voltages outside this limited range. One such example is the Lenovo Yoga
C630, with vdd-3.3-ch0 in particular specified at 3.1V.

But consumers with fixed voltage requirements should just rely on the
board configuration to provide the power at the required level, so this
code should be removed.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

This patch is required for Lenovo Yoga C630 to succeed in power on ath10k, it
can be merged independently of the two following cleanup patches.

drivers/net/wireless/ath/ath10k/snoc.c | 27 ++++++--------------------
drivers/net/wireless/ath/ath10k/snoc.h | 2 --
2 files changed, 6 insertions(+), 23 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c
index fc15a0037f0e..3d93ab09a298 100644
--- a/drivers/net/wireless/ath/ath10k/snoc.c
+++ b/drivers/net/wireless/ath/ath10k/snoc.c
@@ -37,10 +37,10 @@ static char *const ce_name[] = {
};

static struct ath10k_vreg_info vreg_cfg[] = {
- {NULL, "vdd-0.8-cx-mx", 800000, 850000, 0, 0, false},
- {NULL, "vdd-1.8-xo", 1800000, 1850000, 0, 0, false},
- {NULL, "vdd-1.3-rfa", 1300000, 1350000, 0, 0, false},
- {NULL, "vdd-3.3-ch0", 3300000, 3350000, 0, 0, false},
+ {NULL, "vdd-0.8-cx-mx", 0, 0, false},
+ {NULL, "vdd-1.8-xo", 0, 0, false},
+ {NULL, "vdd-1.3-rfa", 0, 0, false},
+ {NULL, "vdd-3.3-ch0", 0, 0, false},
};

static struct ath10k_clk_info clk_cfg[] = {
@@ -1377,9 +1377,8 @@ static int ath10k_get_vreg_info(struct ath10k *ar, struct device *dev,

done:
ath10k_dbg(ar, ATH10K_DBG_SNOC,
- "snog vreg %s min_v %u max_v %u load_ua %u settle_delay %lu\n",
- vreg_info->name, vreg_info->min_v, vreg_info->max_v,
- vreg_info->load_ua, vreg_info->settle_delay);
+ "snog vreg %s load_ua %u settle_delay %lu\n",
+ vreg_info->name, vreg_info->load_ua, vreg_info->settle_delay);

return 0;
}
@@ -1420,15 +1419,6 @@ static int __ath10k_snoc_vreg_on(struct ath10k *ar,
ath10k_dbg(ar, ATH10K_DBG_SNOC, "snoc regulator %s being enabled\n",
vreg_info->name);

- ret = regulator_set_voltage(vreg_info->reg, vreg_info->min_v,
- vreg_info->max_v);
- if (ret) {
- ath10k_err(ar,
- "failed to set regulator %s voltage-min: %d voltage-max: %d\n",
- vreg_info->name, vreg_info->min_v, vreg_info->max_v);
- return ret;
- }
-
if (vreg_info->load_ua) {
ret = regulator_set_load(vreg_info->reg, vreg_info->load_ua);
if (ret < 0) {
@@ -1453,7 +1443,6 @@ static int __ath10k_snoc_vreg_on(struct ath10k *ar,
err_enable:
regulator_set_load(vreg_info->reg, 0);
err_set_load:
- regulator_set_voltage(vreg_info->reg, 0, vreg_info->max_v);

return ret;
}
@@ -1475,10 +1464,6 @@ static int __ath10k_snoc_vreg_off(struct ath10k *ar,
if (ret < 0)
ath10k_err(ar, "failed to set load %s\n", vreg_info->name);

- ret = regulator_set_voltage(vreg_info->reg, 0, vreg_info->max_v);
- if (ret)
- ath10k_err(ar, "failed to set voltage %s\n", vreg_info->name);
-
return ret;
}

diff --git a/drivers/net/wireless/ath/ath10k/snoc.h b/drivers/net/wireless/ath/ath10k/snoc.h
index 9db823e46314..1bf7bd4ef2a3 100644
--- a/drivers/net/wireless/ath/ath10k/snoc.h
+++ b/drivers/net/wireless/ath/ath10k/snoc.h
@@ -45,8 +45,6 @@ struct ath10k_snoc_ce_irq {
struct ath10k_vreg_info {
struct regulator *reg;
const char *name;
- u32 min_v;
- u32 max_v;
u32 load_ua;
unsigned long settle_delay;
bool required;
--
2.18.0