[PATCH v6 2/2] dt/bindings: Add bindings for Layerscape external irqs

[Kurt Kanzenbach <kurt@linutronix.de>]

From: Rasmus Villemoes <rasmus.villemoes@prevas.dk>

This adds Device Tree binding documentation for the external interrupt
lines with configurable polarity present on some Layerscape SOCs.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
---

Changes since v5:

 - Add #address-cells and #size-cells to parent
 - Mention LS2088A and the ISC unit

.../interrupt-controller/fsl,ls-extirq.txt    | 47 +++++++++++++++++++
 1 file changed, 47 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt
new file mode 100644
index 000000000000..7b53f9cc8019
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt
@@ -0,0 +1,47 @@
+* Freescale Layerscape external IRQs
+
+Some Layerscape SOCs (LS1021A, LS1043A, LS1046A, LS2088A) support
+inverting the polarity of certain external interrupt lines.
+
+The device node must be a child of the node representing the
+Supplemental Configuration Unit (SCFG) or the Interrupt Sampling
+Control (ISC) Unit.
+
+Required properties:
+- compatible: should be "fsl,<soc-name>-extirq", e.g. "fsl,ls1021a-extirq".
+- interrupt-controller: Identifies the node as an interrupt controller
+- #interrupt-cells: Must be 2. The first element is the index of the
+  external interrupt line. The second element is the trigger type.
+- interrupt-parent: phandle of GIC.
+- reg: Specifies the Interrupt Polarity Control Register (INTPCR) in the SCFG.
+- fsl,extirq-map: Specifies the mapping to interrupt numbers in the parent
+  interrupt controller. Interrupts are mapped one-to-one to parent
+  interrupts.
+
+Optional properties:
+- fsl,bit-reverse: This boolean property should be set on the LS1021A
+  if the SCFGREVCR register has been set to all-ones (which is usually
+  the case), meaning that all reads and writes of SCFG registers are
+  implicitly bit-reversed. Other compatible platforms do not have such
+  a register.
+
+Example:
+	scfg: scfg@1570000 {
+		compatible = "fsl,ls1021a-scfg", "syscon";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		...
+		extirq: interrupt-controller {
+			compatible = "fsl,ls1021a-extirq";
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			reg = <0x1ac>;
+			fsl,extirq-map = <163 164 165 167 168 169>;
+			fsl,bit-reverse;
+		};
+	};
+
+
+	interrupts-extended = <&gic GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+			      <&extirq 1 IRQ_TYPE_LEVEL_LOW>;
-- 
2.20.1