Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding

[Xin Ji <xji@analogixsemi.com>]

Hi Laurent Pinchart, thanks for your comments.


On Wed, Oct 09, 2019 at 03:10:03PM +0300, Laurent Pinchart wrote:
> Hi Xin Ji,
> 
> Thank you for the patch.
> 
> On Wed, Oct 09, 2019 at 09:27:07AM +0000, Xin Ji wrote:
> > The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> > for portable device. It converts MIPI to DisplayPort 1.3 4K.
> > 
> > You can add support to your board with binding.
> > 
> > Example:
> > 	anx_bridge: anx7625@58 {
> > 		compatible = "analogix,anx7625";
> > 		reg = <0x58>;
> > 		enable-gpios = <&gpio0 45 GPIO_ACTIVE_LOW>;
> > 		reset-gpios = <&gpio0 73 GPIO_ACTIVE_LOW>;
> > 		status = "okay";
> > 		port@0 {
> > 			reg = <0>;
> > 			anx7625_1_in: endpoint {
> > 				remote-endpoint = <&mipi_dsi_bridge_1>;
> > 			};
> > 		};
> > 	};
> > 
> > Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > ---
> >  .../bindings/display/bridge/anx7625.yaml           | 79 ++++++++++++++++++++++
> >  1 file changed, 79 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > new file mode 100644
> > index 0000000..0ef6271
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > @@ -0,0 +1,79 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +# Copyright 2019 Analogix Semiconductor, Inc.
> > +%YAML 1.2
> > +---
> > +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> > +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> > +
> > +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> > +
> > +maintainers:
> > +  - Xin Ji <xji@analogixsemi.com>
> > +
> > +description: |
> > +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> > +  designed for portable devices.
> > +
> > +properties:
> > +  compatible:
> > +    items:
> > +      - const: analogix,anx7625
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  hpd-gpios:
> > +    description: used for HPD interrupt
> > +    maxItems: 1
> 
> You explained in your reply to v1 review that this describes the
> interrupt generated by the ANX7625. It should be replaced by an
> interrupts property.
OK, I'll change it to interrupts property.
> 
> > +
> > +  enable-gpios:
> > +    description: used for power on chip control
> > +    maxItems: 1
> > +
> > +  reset-gpios:
> > +    description: used for reset chip control
> > +    maxItems: 1
> 
> Could you please mention the exact name of the corresponding pins on the
> chip for enable and reset ?
OK, I'll mention the exact name of the corresponding pins on the chip.
> 
> > +
> > +  port@0:
> > +    type: object
> > +    description:
> > +      A port node pointing to MIPI DSI host port node.
> > +
> > +  port@1:
> > +    type: object
> > +    description:
> > +      A port node pointing to MIPI DPI host port node.
> > +
> > +  port@2:
> > +    type: object
> > +    description:
> > +      A port node pointing to external connector port node.
> > +
> > +  port@3:
> > +    type: object
> > +    description:
> > +      A port node pointing to internal panel port node.
> > +
> > +  port@4:
> > +    type: object
> > +    description:
> > +      A port node pointing to normal eDP port node.
> 
> I don't think three output ports is correct. Ports 3 and 4 are really
> the same. I'm even unsure about port 2 and 3, someone with better
> knowledge of USB-C and DisplayPort would be in a better position to
> comment.
I used it to distinguish different output, port@2 used for USB Type-C
output, I need it to register external connector port notifier
interface, and I think it is OK to conbine port@3 and port@4.
> 
> > +
> 
> You're missing the #address-cells and #size-cells properties required
> for the ports. As the device is an I2C device we're lucky that the
> parent will specify compatible address and size cells numbers, but I'm
> not sure we should rely on that luck.
OK, I'll add it.
> 
> Rob, how does yaml schema handle this ?
> 
> > +required:
> > +  - compatible
> > +  - reg
> > +  - port@0 | port@1
> > +
> > +example:
> > +  - |
> > +    anx_bridge: anx7625@58 {
> 
> The node name should describe the device's function. How about
> encoder@58 ?
OK, I'll change it.
> 
> > +        compatible = "analogix,anx7625";
> > +        reg = <0x58>;
> > +        status = "okay";
> > +        port@0 {
> > +          reg = <0>;
> > +          anx7625_1_in: endpoint {
> > +            remote-endpoint = <&mipi_dsi_bridge_1>;
> > +          };
> > +        };
> > +    };
> 
> -- 
> Regards,
> 
> Laurent Pinchart