Re: [PATCH v4 1/2] pinctrl: Add pinmux & GPIO controller driver for a new SoC

[Andy Shevchenko <andriy.shevchenko@intel.com>]

On Thu, Nov 07, 2019 at 03:36:44PM +0800, Rahul Tanwar wrote:
> Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
> controls pin multiplexing & configuration including GPIO functions selection &
> GPIO attributes configuration.
> 
> This IP is not based on & does not have anything in common with Chassis
> specification. The pinctrl drivers under pinctrl/intel/* are all based upon
> Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
> pinctrl framework under pinctrl/intel/* and it requires a separate new driver.
> 
> Add a new GPIO & pin control framework based driver for this IP.

> +static void eqbr_gpio_mask_ack_irq(struct irq_data *d)
> +{
> +	eqbr_gpio_disable_irq(d);
> +	eqbr_gpio_ack_irq(d);

Potential race?

> +}

> +static int eqbr_pinmux_set_mux(struct pinctrl_dev *pctldev,
> +			       unsigned int selector, unsigned int group)
> +{
> +	struct eqbr_pinctrl_drv_data *pctl = pinctrl_dev_get_drvdata(pctldev);
> +	struct function_desc *func;
> +	struct group_desc *grp;
> +	unsigned int *pinmux;
> +	int i;
> +
> +	func = pinmux_generic_get_function(pctldev, selector);
> +	if (!func)
> +		return -EINVAL;
> +
> +	grp = pinctrl_generic_get_group(pctldev, group);
> +	if (!grp)
> +		return -EINVAL;
> +
> +	pinmux = grp->data;

> +	for (i = 0; i < grp->num_pins; i++)
> +		eqbr_set_pin_mux(pctl, pinmux[i], grp->pins[i]);

What if in the middle of the loop mux of one of the pins be changed by parallel
thread?

> +	return 0;
> +}

> +static int eqbr_pinmux_gpio_request(struct pinctrl_dev *pctldev,
> +				    struct pinctrl_gpio_range *range,
> +				    unsigned int pin)
> +{
> +	struct eqbr_pinctrl_drv_data *pctl = pinctrl_dev_get_drvdata(pctldev);
> +

> +	/* 0 mux is reserved for GPIO */

Perhaps

#define EQBR_GPIO_MODE	0

?

> +	return eqbr_set_pin_mux(pctl, 0, pin);
> +}

> +	for (i = 0; i < npins; i++) {
> +		ret = eqbr_pinconf_set(pctldev, pins[i], configs, num_configs);
> +		if (ret)
> +			return ret;

What if in the middle of the loop settings of one of the pins be changed by
parallel thread?

> +	}

> +static int eqbr_build_groups(struct eqbr_pinctrl_drv_data *drvdata)
> +{
> +	struct device *dev = drvdata->dev;
> +	struct device_node *node = dev->of_node;
> +	unsigned int *pinmux, pin_id, pinmux_id;
> +	struct group_desc group;
> +	struct device_node *np;
> +	struct property *prop;
> +	int j, err;
> +
> +	for_each_child_of_node(node, np) {
> +		prop = of_find_property(np, "groups", NULL);
> +		if (!prop)
> +			continue;
> +
> +		group.num_pins = of_property_count_u32_elems(np, "pins");
> +		if (group.num_pins < 0) {

> +			dev_err(dev, "No pins in the group: %s\n",
> +				prop->name);

It is perfectly one line. The idea of if (!foo) pattern in the loop to make
code occupy less LOCs along with increased readability.

> +			return -EINVAL;
> +		}
> +		group.name = prop->value;

> +		group.pins = devm_kcalloc(dev, group.num_pins,
> +					  sizeof(*(group.pins)), GFP_KERNEL);
> +		pinmux = devm_kcalloc(dev, group.num_pins,
> +				      sizeof(*pinmux), GFP_KERNEL);

These can be rearranged.

> +
> +		if (!group.pins || !pinmux)
> +			return -ENOMEM;
> +		for (j = 0; j < group.num_pins; j++) {

> +			if (of_property_read_u32_index(np, "pins",
> +						       j, &pin_id)) {

One line.

And so on...

> +				dev_err(dev, "Group %s: Read intel pins id failed\n",
> +					group.name);
> +				return -EINVAL;
> +			}
> +			if (pin_id >= drvdata->pctl_desc.npins) {
> +				dev_err(dev, "Group %s: Invalid pin ID, idx: %d, pin %u\n",
> +					group.name, j, pin_id);
> +				return -EINVAL;
> +			}
> +			group.pins[j] = pin_id;
> +			if (of_property_read_u32_index(np, "pinmux",
> +						       j, &pinmux_id)) {
> +				dev_err(dev, "Group %s: Read intel pinmux id failed\n",
> +					group.name);
> +				return -EINVAL;
> +			}
> +			pinmux[j] = pinmux_id;
> +		}
> +
> +		err = pinctrl_generic_add_group(drvdata->pctl_dev, group.name,
> +						group.pins, group.num_pins,
> +						pinmux);
> +		if (err < 0) {
> +			dev_err(dev, "Failed to register group %s\n",
> +				group.name);
> +			return err;
> +		}
> +		memset(&group, 0, sizeof(group));
> +		pinmux = NULL;
> +	}
> +
> +	return 0;
> +}

-- 
With Best Regards,
Andy Shevchenko