Re: [PATCH v4 3/5] remoteproc: Add prepare/unprepare callbacks

[Bjorn Andersson <bjorn.andersson@linaro.org>]

On Tue 10 Dec 08:40 PST 2019, Paul Cercueil wrote:

> The .prepare() callback is called before the firmware is loaded to
> memory. This is useful for instance in the case where some setup is
> required for the memory to be accessible.
> 

Would it make sense to somehow tie this prepare/unprepare to the actual
struct rproc_mem_entry that needs the resource enabled?

Regards,
Bjorn

> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Notes:
>     v2-v4: No change
> 
>  drivers/remoteproc/remoteproc_core.c | 16 +++++++++++++++-
>  include/linux/remoteproc.h           |  4 ++++
>  2 files changed, 19 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/remoteproc/remoteproc_core.c b/drivers/remoteproc/remoteproc_core.c
> index 0a9fc7fdd1c3..3ea5f675a148 100644
> --- a/drivers/remoteproc/remoteproc_core.c
> +++ b/drivers/remoteproc/remoteproc_core.c
> @@ -1299,11 +1299,19 @@ static int rproc_start(struct rproc *rproc, const struct firmware *fw)
>  	struct device *dev = &rproc->dev;
>  	int ret;
>  
> +	if (rproc->ops->prepare) {
> +		ret = rproc->ops->prepare(rproc);
> +		if (ret) {
> +			dev_err(dev, "Failed to prepare rproc: %d\n", ret);
> +			return ret;
> +		}
> +	}
> +
>  	/* load the ELF segments to memory */
>  	ret = rproc_load_segments(rproc, fw);
>  	if (ret) {
>  		dev_err(dev, "Failed to load program segments: %d\n", ret);
> -		return ret;
> +		goto unprepare_rproc;
>  	}
>  
>  	/*
> @@ -1354,6 +1362,9 @@ static int rproc_start(struct rproc *rproc, const struct firmware *fw)
>  	rproc_unprepare_subdevices(rproc);
>  reset_table_ptr:
>  	rproc->table_ptr = rproc->cached_table;
> +unprepare_rproc:
> +	if (rproc->ops->unprepare)
> +		rproc->ops->unprepare(rproc);
>  
>  	return ret;
>  }
> @@ -1483,6 +1494,9 @@ static int rproc_stop(struct rproc *rproc, bool crashed)
>  
>  	rproc->state = RPROC_OFFLINE;
>  
> +	if (rproc->ops->unprepare)
> +		rproc->ops->unprepare(rproc);
> +
>  	dev_info(dev, "stopped remote processor %s\n", rproc->name);
>  
>  	return 0;
> diff --git a/include/linux/remoteproc.h b/include/linux/remoteproc.h
> index 5f201f0c86c3..a6272d1ba384 100644
> --- a/include/linux/remoteproc.h
> +++ b/include/linux/remoteproc.h
> @@ -355,6 +355,8 @@ enum rsc_handling_status {
>  
>  /**
>   * struct rproc_ops - platform-specific device handlers
> + * @prepare:	prepare the device for power up (before the firmware is loaded)
> + * @unprepare:	unprepare the device after it is stopped
>   * @start:	power on the device and boot it
>   * @stop:	power off the device
>   * @kick:	kick a virtqueue (virtqueue id given as a parameter)
> @@ -371,6 +373,8 @@ enum rsc_handling_status {
>   * @get_boot_addr:	get boot address to entry point specified in firmware
>   */
>  struct rproc_ops {
> +	int (*prepare)(struct rproc *rproc);
> +	void (*unprepare)(struct rproc *rproc);
>  	int (*start)(struct rproc *rproc);
>  	int (*stop)(struct rproc *rproc);
>  	void (*kick)(struct rproc *rproc, int vqid);
> -- 
> 2.24.0
>