[PATCH 3/4] interconnect: qcom: Add support for per-BCM scaling factors

[Mike Tipton <mdtipton@codeaurora.org>]

Currently, bcm-voter always assumes requests are made in KBps and that
BCM HW always wants them in Bps, so it always scales the requests by
1000. However, certain use cases and BCMs may use different units.
Thus, add support for BCM-specific scaling factors.

Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
---
 drivers/interconnect/qcom/bcm-voter.c | 4 ++--
 drivers/interconnect/qcom/icc-rpmh.c  | 3 +++
 drivers/interconnect/qcom/icc-rpmh.h  | 2 ++
 3 files changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/interconnect/qcom/bcm-voter.c b/drivers/interconnect/qcom/bcm-voter.c
index bb83ce7554b7..a68c858ca6b7 100644
--- a/drivers/interconnect/qcom/bcm-voter.c
+++ b/drivers/interconnect/qcom/bcm-voter.c
@@ -72,11 +72,11 @@ static void bcm_aggregate(struct qcom_icc_bcm *bcm)
 			agg_peak[bucket] = max(agg_peak[bucket], temp);
 		}
 
-		temp = agg_avg[bucket] * 1000ULL;
+		temp = agg_avg[bucket] * bcm->vote_scale;
 		do_div(temp, bcm->aux_data.unit);
 		bcm->vote_x[bucket] = temp;
 
-		temp = agg_peak[bucket] * 1000ULL;
+		temp = agg_peak[bucket] * bcm->vote_scale;
 		do_div(temp, bcm->aux_data.unit);
 		bcm->vote_y[bucket] = temp;
 	}
diff --git a/drivers/interconnect/qcom/icc-rpmh.c b/drivers/interconnect/qcom/icc-rpmh.c
index 3ac5182c9ab2..008846c17bec 100644
--- a/drivers/interconnect/qcom/icc-rpmh.c
+++ b/drivers/interconnect/qcom/icc-rpmh.c
@@ -136,6 +136,9 @@ int qcom_icc_bcm_init(struct qcom_icc_bcm *bcm, struct device *dev)
 	INIT_LIST_HEAD(&bcm->list);
 	INIT_LIST_HEAD(&bcm->ws_list);
 
+	if (!bcm->vote_scale)
+		bcm->vote_scale = 1000;
+
 	/* Link Qnodes to their respective BCMs */
 	for (i = 0; i < bcm->num_nodes; i++) {
 		qn = bcm->nodes[i];
diff --git a/drivers/interconnect/qcom/icc-rpmh.h b/drivers/interconnect/qcom/icc-rpmh.h
index 903d25e61984..200e98be5926 100644
--- a/drivers/interconnect/qcom/icc-rpmh.h
+++ b/drivers/interconnect/qcom/icc-rpmh.h
@@ -94,6 +94,7 @@ struct qcom_icc_node {
  * @addr: address offsets used when voting to RPMH
  * @vote_x: aggregated threshold values, represents sum_bw when @type is bw bcm
  * @vote_y: aggregated threshold values, represents peak_bw when @type is bw bcm
+ * @vote_scale: scaling factor for vote_x and vote_y
  * @dirty: flag used to indicate whether the bcm needs to be committed
  * @keepalive: flag used to indicate whether a keepalive is required
  * @aux_data: auxiliary data used when calculating threshold values and
@@ -109,6 +110,7 @@ struct qcom_icc_bcm {
 	u32 addr;
 	u64 vote_x[QCOM_ICC_NUM_BUCKETS];
 	u64 vote_y[QCOM_ICC_NUM_BUCKETS];
+	u64 vote_scale;
 	bool dirty;
 	bool keepalive;
 	struct bcm_db aux_data;
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project