[PATCH RESEND net-next v3 0/3] net: enetc: remove bootloader dependency

[Michael Walle <michael@walle.cc>]

This is a resend of the series because the conversion to the phylink
interface will likely take longer:
https://lore.kernel.org/netdev/CA+h21hpBodyY8CtNH2ktRdc2FqPi=Fjp94=VVZvzSVbnvnfKVg@mail.gmail.com/
Unfortunately, we have boards in the wild with a bootloader which doesn't
set the PCS up correctly. Thus I'd really see this patches picked up as an
intermediate step until the phylink conversion is ready. Vladimir Oltean
already offered to convert enetc to phylink when he converts the felix to
phylink. After this series the PCS setup of the enetc looks almost the same
as the current felix setup. Thus conversion should be easy.

These patches were picked from the following series:
https://lore.kernel.org/netdev/1567779344-30965-1-git-send-email-claudiu.manoil@nxp.com/
They have never been resent. I've picked them up, addressed Andrews
comments, fixed some more bugs and asked Claudiu if I can keep their SOB
tags; he agreed. I've tested this on our board which happens to have a
bootloader which doesn't do the enetc setup in all cases. Though, only
SGMII mode was tested.

changes since v2:
 - removed SOBs from "net: enetc: Initialize SerDes for SGMII and USXGMII
   protocols" because almost everything has changed.
 - get a phy_device for the internal PCS PHY so we can use the phy_
   functions instead of raw mdiobus writes
 - reuse macros already defined in fsl_mdio.h, move missing bits from
   felix to fsl_mdio.h, because they share the same PCS PHY building
   block
 - added 2500BaseX mode (based on felix init routine)
 - changed xgmii mode to usxgmii mode, because it is actually USXGMII and
   felix does the same.
 - fixed devad, which is 0x1f (MMD_VEND2)

changes since v1:
 - mdiobus id is '"imdio-%s", dev_name(dev)' because the plain dev_name()
   is used by the emdio.
 - use mdiobus_write() instead of imdio->write(imdio, ..), since this is
   already a full featured mdiobus
 - set phy_mask to ~0 to avoid scanning the bus
 - use phy_interface_mode_is_rgmii(phy_mode) to also include the RGMII
   modes with pad delays.
 - move enetc_imdio_init() to enetc_pf.c, there shouldn't be any other
   users, should it?
 - renamed serdes to SerDes
 - printing the error code of mdiobus_register() in the error path
 - call mdiobus_unregister() on _remove()
 - call devm_mdiobus_free() if mdiobus_register() fails, since an
   error is not fatal

Alex Marginean (1):
  net: enetc: Use DT protocol information to set up the ports

Michael Walle (2):
  net: dsa: felix: move USXGMII defines to common place
  net: enetc: Initialize SerDes for SGMII and USXGMII protocols

 drivers/net/dsa/ocelot/felix_vsc9959.c        |  21 --
 .../net/ethernet/freescale/enetc/enetc_hw.h   |   3 +
 .../net/ethernet/freescale/enetc/enetc_pf.c   | 191 +++++++++++++++---
 .../net/ethernet/freescale/enetc/enetc_pf.h   |   5 +
 include/linux/fsl/enetc_mdio.h                |  19 ++
 5 files changed, 194 insertions(+), 45 deletions(-)

-- 
2.20.1