From: Shawn Guo <shawnguo@kernel.org>
To: Abel Vesa <abel.vesa@nxp.com>
Cc: Georgi Djakov <georgi.djakov@linaro.org>,
Chanwoo Choi <cw00.choi@samsung.com>,
Leonard Crestez <cdleonard@gmail.com>,
Rob Herring <robh@kernel.org>, NXP Linux Team <linux-imx@nxp.com>,
devicetree@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
linux-arm-kernel@lists.infradead.org,
Leonard Crestez <leonard.crestez@nxp.com>
Subject: Re: [RESEND v2] arm64: dts: imx8m: Add NOC nodes
Date: Sat, 11 Jul 2020 22:26:43 +0800 [thread overview]
Message-ID: <20200711142642.GJ21277@dragon> (raw)
In-Reply-To: <1594070006-816-1-git-send-email-abel.vesa@nxp.com>
On Tue, Jul 07, 2020 at 12:13:26AM +0300, Abel Vesa wrote:
> From: Leonard Crestez <leonard.crestez@nxp.com>
>
> Add nodes for the main interconnect of the imx8m series chips.
>
> These nodes are bound to by devfreq and interconnect drivers.
>
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
> Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
> Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
> Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
> ---
>
> Changes since v1:
> - picked up the bindinds header which were part of the original patch
> from Leonard
>
> arch/arm64/boot/dts/freescale/imx8mm.dtsi | 24 ++++++++++++++++++++++++
> arch/arm64/boot/dts/freescale/imx8mn.dtsi | 24 ++++++++++++++++++++++++
> arch/arm64/boot/dts/freescale/imx8mq.dtsi | 24 ++++++++++++++++++++++++
> 3 files changed, 72 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> index 76f040e..970d132 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> @@ -8,6 +8,7 @@
> #include <dt-bindings/input/input.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/thermal/thermal.h>
> +#include <dt-bindings/interconnect/imx8mm.h>
>
> #include "imx8mm-pinfunc.h"
>
> @@ -877,6 +878,29 @@
>
> };
>
> + noc: interconnect@32700000 {
> + compatible = "fsl,imx8mm-noc", "fsl,imx8m-noc";
> + reg = <0x32700000 0x100000>;
> + clocks = <&clk IMX8MM_CLK_NOC>;
> + fsl,ddrc = <&ddrc>;
> + #interconnect-cells = <1>;
> + operating-points-v2 = <&noc_opp_table>;
> +
> + noc_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-150M {
> + opp-hz = /bits/ 64 <150000000>;
> + };
Please have a newline between nodes.
Shawn
> + opp-375M {
> + opp-hz = /bits/ 64 <375000000>;
> + };
> + opp-750M {
> + opp-hz = /bits/ 64 <750000000>;
> + };
> + };
> + };
> +
> aips4: bus@32c00000 {
> compatible = "fsl,aips-bus", "simple-bus";
> reg = <0x32c00000 0x400000>;
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
> index 9385dd7..cd38aae 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
> @@ -8,6 +8,7 @@
> #include <dt-bindings/input/input.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/thermal/thermal.h>
> +#include <dt-bindings/interconnect/imx8mn.h>
>
> #include "imx8mn-pinfunc.h"
>
> @@ -764,6 +765,29 @@
>
> };
>
> + noc: interconnect@32700000 {
> + compatible = "fsl,imx8mn-noc", "fsl,imx8m-noc";
> + reg = <0x32700000 0x100000>;
> + clocks = <&clk IMX8MN_CLK_NOC>;
> + fsl,ddrc = <&ddrc>;
> + #interconnect-cells = <1>;
> + operating-points-v2 = <&noc_opp_table>;
> +
> + noc_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-100M {
> + opp-hz = /bits/ 64 <100000000>;
> + };
> + opp-600M {
> + opp-hz = /bits/ 64 <600000000>;
> + };
> + opp-800M {
> + opp-hz = /bits/ 64 <800000000>;
> + };
> + };
> + };
> +
> aips4: bus@32c00000 {
> compatible = "fsl,aips-bus", "simple-bus";
> reg = <0x32c00000 0x400000>;
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> index f70435c..d585650 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> @@ -11,6 +11,7 @@
> #include "dt-bindings/input/input.h"
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/thermal/thermal.h>
> +#include <dt-bindings/interconnect/imx8mq.h>
> #include "imx8mq-pinfunc.h"
>
> / {
> @@ -1045,6 +1046,29 @@
> };
> };
>
> + noc: interconnect@32700000 {
> + compatible = "fsl,imx8mq-noc", "fsl,imx8m-noc";
> + reg = <0x32700000 0x100000>;
> + clocks = <&clk IMX8MQ_CLK_NOC>;
> + fsl,ddrc = <&ddrc>;
> + #interconnect-cells = <1>;
> + operating-points-v2 = <&noc_opp_table>;
> +
> + noc_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-133M {
> + opp-hz = /bits/ 64 <133333333>;
> + };
> + opp-400M {
> + opp-hz = /bits/ 64 <400000000>;
> + };
> + opp-800M {
> + opp-hz = /bits/ 64 <800000000>;
> + };
> + };
> + };
> +
> bus@32c00000 { /* AIPS4 */
> compatible = "fsl,aips-bus", "simple-bus";
> reg = <0x32c00000 0x400000>;
> --
> 2.7.4
>
next prev parent reply other threads:[~2020-07-11 14:27 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-06 21:13 [RESEND v2] arm64: dts: imx8m: Add NOC nodes Abel Vesa
2020-07-11 14:26 ` Shawn Guo [this message]
2020-07-13 18:31 ` Georgi Djakov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200711142642.GJ21277@dragon \
--to=shawnguo@kernel.org \
--cc=abel.vesa@nxp.com \
--cc=cdleonard@gmail.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=georgi.djakov@linaro.org \
--cc=leonard.crestez@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox