Re: [greybus-dev] [RFC PATCH v2 3/3] Add Device Tree Bindings for mikroBUS port

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Vaishnav,

Thank you for the patch.

On Tue, Aug 18, 2020 at 06:18:15PM +0530, Vaishnav M A wrote:
> This patch adds device tree bindings for the mikroBUS port,
> device tree overlays for the mikrobus Port on the BeagleBoard.org
> PocketBeagle is available here :
> github.com/beagleboard/bb.org-overlays/blob/master/src/arm/PB-MIKROBUS-0.dts
> 
> Signed-off-by: Vaishnav M A <vaishnav@beagleboard.org>
> ---
>  .../bindings/misc/linux,mikrobus.txt          | 81 +++++++++++++++++++

Would you mind converting this binding document to YAML ? For new
bindings we're trying to enforce usage of YAML, to avoid increasing the
conversion backlog.

>  1 file changed, 81 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/misc/linux,mikrobus.txt
> 
> diff --git a/Documentation/devicetree/bindings/misc/linux,mikrobus.txt b/Documentation/devicetree/bindings/misc/linux,mikrobus.txt
> new file mode 100644
> index 000000000000..99f75caf5f35
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/linux,mikrobus.txt
> @@ -0,0 +1,81 @@
> +mikroBUS add-on board socket
> +
> +Required properties:
> +- compatible: Must be "linux,mikrobus"
> +- i2c-adapter:  phandle to the i2c adapter attached to the mikrobus socket.
> +- spi-master: spi bus number of the spi-master attached to the mikrobus socket.
> +- spi-cs: spi chip-select numbers corresponding to the chip-selects
> +	  on the mikrobus socket(0 -> chip select corresponding to CS pin
> +	  1 -> chip select corresponding to RST pin).
> +- serdev-controller:  phandle to the uart port attached to the mikrobus socket.
> +- pwms: phandle to the pwm-controller corresponding to the mikroBUS PWM pin.
> +- mikrobus-gpios: gpios array corresponding to GPIOs on the mikroBUS port,
> +		  for targets not supporting the AN pin on the mikroBUS port as
> +		  GPIO, the length of the gpios array can be 11, otherwise it
> +		  should be 12.
> +- pinctrl-names: pinctrl state names to support additional pin usage/deviations
> +		 from mikroBUS socket standard usage, must be "default",
> +		 "pwm_default", "pwm_gpio", "uart_default", "uart_gpio",
> +		 "i2c_default", "i2c_gpio", "spi_default", "spi_gpio", these
> +		 pinctrl names should have corresponding pinctrl-N entries which
> +		 corresponds to the pinmux state for the pingroup, for example,
> +		 i2c_default corresponds to the state where the I2C pin group
> +		 (SCL,SDA) are configured in I2C mode and i2c_gpio mode corresponds
> +		 to the pinmux state where these pins are configured as GPIO.
> +- pinctrl-N : pinctrl-(0-8) corresponds to the pinctrl states for the states described
> +	      above.
> +
> +Example:
> +	mikrobus-0 {
> +		compatible = "linux,mikrobus";
> +		status = "okay";
> +		pinctrl-names = "default", "pwm_default", "pwm_gpio",
> +				"uart_default", "uart_gpio", "i2c_default",
> +				"i2c_gpio", "spi_default", "spi_gpio";
> +		pinctrl-0 = <
> +			&P2_03_gpio_input_pin
> +			&P1_04_gpio_pin
> +			&P1_02_gpio_pin
> +		>;
> +		pinctrl-1 = <&P2_01_pwm_pin>;
> +		pinctrl-2 = <&P2_01_gpio_pin>;
> +		pinctrl-3 = <
> +			&P2_05_uart_pin
> +			&P2_07_uart_pin
> +		>;
> +		pinctrl-4 = <
> +			&P2_05_gpio_pin
> +			&P2_07_gpio_pin
> +		>;
> +		pinctrl-5 = <
> +			&P2_09_i2c_pin
> +			&P2_11_i2c_pin
> +		>;
> +		pinctrl-6 = <
> +			&P2_09_gpio_pin
> +			&P2_11_gpio_pin
> +		>;
> +		pinctrl-7 = <
> +			&P1_12_spi_pin
> +			&P1_10_spi_pin
> +			&P1_08_spi_sclk_pin
> +			&P1_06_spi_cs_pin
> +		>;
> +		pinctrl-8 = <
> +			&P1_12_gpio_pin
> +			&P1_10_gpio_pin
> +			&P1_08_gpio_pin
> +			&P1_06_gpio_pin
> +		>;
> +		i2c-adapter = <&i2c1>;
> +		spi-master = <0>;
> +		spi-cs = <0 1>;
> +		serdev-controller = <&uart4>;
> +		pwms = <&ehrpwm1 0 500000 0>;
> +		mikrobus-gpios = <&gpio1 18 0> , <&gpio0 23 0>,
> +					<&gpio0 30 0> , <&gpio0 31 0>,
> +					<&gpio0 15 0> , <&gpio0 14 0>,
> +					<&gpio0 4 0> , <&gpio0 3 0>,
> +					<&gpio0 2 0> , <&gpio0 5 0>,
> +					<&gpio2 25 0>  , <&gpio2 3 0>;
> +	};
> \ No newline at end of file

-- 
Regards,

Laurent Pinchart