RE: [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema

Fabrizio Castro
2020-09-16T18:55:57Z

Hi Laurent,

Thank you for your feedback.

> From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Sent: 15 September 2020 18:45
>
> On Tue, Sep 15, 2020 at 08:36:39PM +0300, Laurent Pinchart wrote:
> > Hi Fabrizio,
> >
> > Thank you for the patch.
> >
> > On Tue, Sep 15, 2020 at 02:12:15PM +0100, Fabrizio Castro wrote:
> > > Convert the Renesas DRIF bindings to DT schema and update
> > > MAINTAINERS accordingly.
> > >
> > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
> > > ---
> > > .../bindings/media/renesas,drif.txt | 177 ------------
> > > .../bindings/media/renesas,drif.yaml | 270 ++++++++++++++++++
> > > MAINTAINERS | 2 +-
> > > 3 files changed, 271 insertions(+), 178 deletions(-)
> > > delete mode 100644
> Documentation/devicetree/bindings/media/renesas,drif.txt
> > > create mode 100644
> Documentation/devicetree/bindings/media/renesas,drif.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt
> b/Documentation/devicetree/bindings/media/renesas,drif.txt
> > > deleted file mode 100644
> > > index 0d8974aa8b38..000000000000
> > > --- a/Documentation/devicetree/bindings/media/renesas,drif.txt
> > > +++ /dev/null
> > > @@ -1,177 +0,0 @@
> > > -Renesas R-Car Gen3 Digital Radio Interface controller (DRIF)
> > > -------------------------------------------------------------
> > > -
> > > -R-Car Gen3 DRIF is a SPI like receive only slave device. A general
> > > -representation of DRIF interfacing with a master device is shown below.
> > > -
> > > -+---------------------+ +---------------------+
> > > -| |-----SCK------->|CLK |
> > > -| Master |-----SS-------->|SYNC DRIFn (slave) |
> > > -| |-----SD0------->|D0 |
> > > -| |-----SD1------->|D1 |
> > > -+---------------------+ +---------------------+
> > > -
> > > -As per datasheet, each DRIF channel (drifn) is made up of two internal
> > > -channels (drifn0 & drifn1). These two internal channels share the
> common
> > > -CLK & SYNC. Each internal channel has its own dedicated resources like
> > > -irq, dma channels, address space & clock. This internal split is not
> > > -visible to the external master device.
> > > -
> > > -The device tree model represents each internal channel as a separate
> node.
> > > -The internal channels sharing the CLK & SYNC are tied together by their
> > > -phandles using a property called "renesas,bonding". For the rest of
> > > -the documentation, unless explicitly stated, the word channel implies an
> > > -internal channel.
> > > -
> > > -When both internal channels are enabled they need to be managed
> together
> > > -as one (i.e.) they cannot operate alone as independent devices. Out of
> the
> > > -two, one of them needs to act as a primary device that accepts common
> > > -properties of both the internal channels. This channel is identified by a
> > > -property called "renesas,primary-bond".
> > > -
> > > -To summarize,
> > > - - When both the internal channels that are bonded together are
> enabled,
> > > - the zeroth channel is selected as primary-bond. This channels accepts
> > > - properties common to all the members of the bond.
> > > - - When only one of the bonded channels need to be enabled, the
> property
> > > - "renesas,bonding" or "renesas,primary-bond" will have no effect.
> That
> > > - enabled channel can act alone as any other independent device.
> > > -
> > > -Required properties of an internal channel:
> > > --------------------------------------------
> > > -- compatible:"renesas,r8a7795-drif" if DRIF controller is a part of
> R8A7795 SoC.
> > > -"renesas,r8a7796-drif" if DRIF controller is a part of R8A7796
> SoC.
> > > -"renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible
> device.
> > > -
> > > -When compatible with the generic version, nodes must list
> the
> > > -SoC-specific version corresponding to the platform first
> > > -followed by the generic version.
> > > -
> > > -- reg: offset and length of that channel.
> > > -- interrupts: associated with that channel.
> > > -- clocks: phandle and clock specifier of that channel.
> > > -- clock-names: clock input name string: "fck".
> > > -- dmas: phandles to the DMA channels.
> > > -- dma-names: names of the DMA channel: "rx".
> > > -- renesas,bonding: phandle to the other channel.
> > > -
> > > -Optional properties of an internal channel:
> > > --------------------------------------------
> > > -- power-domains: phandle to the respective power domain.
> > > -
> > > -Required properties of an internal channel when:
> > > -- It is the only enabled channel of the bond (or)
> > > -- If it acts as primary among enabled bonds
> > > ---------------------------------------------------------
> > > -- pinctrl-0: pin control group to be used for this channel.
> > > -- pinctrl-names: must be "default".
> > > -- renesas,primary-bond: empty property indicating the channel acts as
> primary
> > > -among the bonded channels.
> > > -- port: child port node corresponding to the data input, in accordance
> with
> > > -the video interface bindings defined in
> > > -Documentation/devicetree/bindings/media/video-interfaces.txt.
> The port
> > > -node must contain at least one endpoint.
> > > -
> > > -Optional endpoint property:
> > > ----------------------------
> > > -- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively.
> > > - This property maps to SYNCAC bit in the hardware manual. The
> > > - default is 1 (active high).
> > > -
> > > -Example:
> > > ---------
> > > -
> > > -(1) Both internal channels enabled:
> > > ------------------------------------
> > > -
> > > -When interfacing with a third party tuner device with two data pins as
> shown
> > > -below.
> > > -
> > > -+---------------------+ +---------------------+
> > > -| |-----SCK------->|CLK |
> > > -| Master |-----SS-------->|SYNC DRIFn (slave) |
> > > -| |-----SD0------->|D0 |
> > > -| |-----SD1------->|D1 |
> > > -+---------------------+ +---------------------+
> > > -
> > > -drif00: rif@e6f40000 {
> > > -compatible = "renesas,r8a7795-drif",
> > > - "renesas,rcar-gen3-drif";
> > > -reg = <0 0xe6f40000 0 0x64>;
> > > -interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> > > -clocks = <&cpg CPG_MOD 515>;
> > > -clock-names = "fck";
> > > -dmas = <&dmac1 0x20>, <&dmac2 0x20>;
> > > -dma-names = "rx", "rx";
> > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > -renesas,bonding = <&drif01>;
> > > -renesas,primary-bond;
> > > -pinctrl-0 = <&drif0_pins>;
> > > -pinctrl-names = "default";
> > > -port {
> > > -drif0_ep: endpoint {
> > > - remote-endpoint = <&tuner_ep>;
> > > -};
> > > -};
> > > -};
> > > -
> > > -drif01: rif@e6f50000 {
> > > -compatible = "renesas,r8a7795-drif",
> > > - "renesas,rcar-gen3-drif";
> > > -reg = <0 0xe6f50000 0 0x64>;
> > > -interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> > > -clocks = <&cpg CPG_MOD 514>;
> > > -clock-names = "fck";
> > > -dmas = <&dmac1 0x22>, <&dmac2 0x22>;
> > > -dma-names = "rx", "rx";
> > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > -renesas,bonding = <&drif00>;
> > > -};
> > > -
> > > -
> > > -(2) Internal channel 1 alone is enabled:
> > > -----------------------------------------
> > > -
> > > -When interfacing with a third party tuner device with one data pin as
> shown
> > > -below.
> > > -
> > > -+---------------------+ +---------------------+
> > > -| |-----SCK------->|CLK |
> > > -| Master |-----SS-------->|SYNC DRIFn (slave) |
> > > -| | |D0 (unused) |
> > > -| |-----SD-------->|D1 |
> > > -+---------------------+ +---------------------+
> > > -
> > > -drif00: rif@e6f40000 {
> > > -compatible = "renesas,r8a7795-drif",
> > > - "renesas,rcar-gen3-drif";
> > > -reg = <0 0xe6f40000 0 0x64>;
> > > -interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> > > -clocks = <&cpg CPG_MOD 515>;
> > > -clock-names = "fck";
> > > -dmas = <&dmac1 0x20>, <&dmac2 0x20>;
> > > -dma-names = "rx", "rx";
> > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > -renesas,bonding = <&drif01>;
> > > -};
> > > -
> > > -drif01: rif@e6f50000 {
> > > -compatible = "renesas,r8a7795-drif",
> > > - "renesas,rcar-gen3-drif";
> > > -reg = <0 0xe6f50000 0 0x64>;
> > > -interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> > > -clocks = <&cpg CPG_MOD 514>;
> > > -clock-names = "fck";
> > > -dmas = <&dmac1 0x22>, <&dmac2 0x22>;
> > > -dma-names = "rx", "rx";
> > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > -renesas,bonding = <&drif00>;
> > > -pinctrl-0 = <&drif0_pins>;
> > > -pinctrl-names = "default";
> > > -port {
> > > -drif0_ep: endpoint {
> > > - remote-endpoint = <&tuner_ep>;
> > > - sync-active = <0>;
> > > -};
> > > -};
> > > -};
> > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml
> b/Documentation/devicetree/bindings/media/renesas,drif.yaml
> > > new file mode 100644
> > > index 000000000000..f57fccc159d6
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml
> > > @@ -0,0 +1,270 @@
> > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/media/renesas,drif.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Renesas R-Car Gen3 Digital Radio Interface controller (DRIF)
> >
> > s/controller/Controller/

Will fix with V2

> >
> > > +
> > > +maintainers:
> > > + - Ramesh Shanmugasundaram <rashanmu@gmail.com>
> > > + - Fabrizio Castro <fabrizio.castro.jz@renesas.com>
> > > +
> > > +description: |
> > > + R-Car Gen3 DRIF is a SPI like receive only slave device. A general
> > > + representation of DRIF interfacing with a master device is shown
> below.
> > > +
> > > + +---------------------+ +---------------------+
> > > + | |-----SCK------->|CLK |
> > > + | Master |-----SS-------->|SYNC DRIFn (slave) |
> > > + | |-----SD0------->|D0 |
> > > + | |-----SD1------->|D1 |
> > > + +---------------------+ +---------------------+
> > > +
> > > + As per datasheet, each DRIF channel (drifn) is made up of two internal
> > > + channels (drifn0 & drifn1). These two internal channels share the
> common
> > > + CLK & SYNC. Each internal channel has its own dedicated resources like
> > > + irq, dma channels, address space & clock. This internal split is not
> > > + visible to the external master device.
> > > +
> > > + The device tree model represents each internal channel as a separate
> node.
> > > + The internal channels sharing the CLK & SYNC are tied together by their
> > > + phandles using a property called "renesas,bonding". For the rest of
> > > + the documentation, unless explicitly stated, the word channel implies
> an
> > > + internal channel.
> > > +
> > > + When both internal channels are enabled they need to be managed
> together
> > > + as one (i.e.) they cannot operate alone as independent devices. Out of
> the
> > > + two, one of them needs to act as a primary device that accepts
> common
> > > + properties of both the internal channels. This channel is identified by a
> > > + property called "renesas,primary-bond".
> > > +
> > > + To summarize,
> > > + * When both the internal channels that are bonded together are
> enabled,
> > > + the zeroth channel is selected as primary-bond. This channels
> accepts
> > > + properties common to all the members of the bond.
> > > + * When only one of the bonded channels need to be enabled, the
> property
> > > + "renesas,bonding" or "renesas,primary-bond" will have no effect.
> That
> > > + enabled channel can act alone as any other independent device.
> > > +
> > > +properties:
> > > + compatible:
> > > + items:
> > > + - enum:
> > > + - renesas,r8a7795-drif # R-Car H3
> > > + - renesas,r8a7796-drif # R-Car M3-W
> > > + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible
> device
> > > +
> > > + reg:
> > > + maxItems: 1
> > > +
> > > + interrupts:
> > > + maxItems: 1
> > > +
> > > + clocks:
> > > + maxItems: 1
> > > +
> > > + clock-names:
> > > + maxItems: 1
> > > + items:
> > > + - const: fck
> > > +
> > > + resets:
> > > + maxItems: 1
> > > +
> > > + dmas:
> > > + minItems: 1
> > > + maxItems: 2
> > > +
> > > + dma-names:
> > > + minItems: 1
> > > + maxItems: 2
> > > + items:
> > > + - const: rx
> > > + - const: rx
> > > +
> > > + renesas,bonding:
> > > + $ref: /schemas/types.yaml#/definitions/phandle
> > > + description:
> > > + The phandle to the other internal channel of DRIF
> > > +
> > > + power-domains:
> > > + maxItems: 1
> > > +
> > > + pinctrl-0:
> > > + maxItems: 1
> > > +
> > > + pinctrl-names:
> > > + maxItems: 1
> > > + items:
> > > + - const: default
> >
> > You can drop those three properties, they're already handled by
> > dt-schema.
>
> It looks like I'm wrong, power-domains seems to be required. I'm not
> sure why though, as the power-domain-consumer.yaml schema has select:
> true. Maybe Rob can comment on this, in the meantime let's keep the
> power-domains property.

Ok, will leave it for v2, and wait for Rob's reply.

Thanks,
Fab

>
> > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> >
> > > +
> > > + renesas,primary-bond:
> > > + type: boolean
> > > + description:
> > > + Indicates that the channel acts as primary among the bonded
> channels.
> > > +
> > > + port:
> > > + type: object
> > > + description:
> > > + Child port node corresponding to the data input, in accordance with
> the
> > > + video interface bindings defined in
> > > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > > + The port node must contain at least one endpoint.
> > > +
> > > + properties:
> > > + endpoint:
> > > + type: object
> > > +
> > > + properties:
> > > + remote-endpoint:
> > > + description:
> > > + A phandle to the remote tuner endpoint subnode in remote
> node
> > > + port.
> > > +
> > > + sync-active:
> > > + enum: [0, 1]
> > > + description:
> > > + Indicates sync signal polarity, 0/1 for low/high respectively.
> > > + This property maps to SYNCAC bit in the hardware manual. The
> > > + default is 1 (active high).
> > > +
> > > + additionalProperties: false
> > > +
> > > +required:
> > > + - compatible
> > > + - reg
> > > + - interrupts
> > > + - clocks
> > > + - clock-names
> > > + - resets
> > > + - dmas
> > > + - dma-names
> > > + - renesas,bonding
> > > +
> > > +if:
> > > + required:
> > > + - renesas,primary-bond
> > > +then:
> > > + required:
> > > + - pinctrl-0
> > > + - pinctrl-names
> > > + - port
> > > +
> > > +additionalProperties: false
> > > +
> > > +examples:
> > > + # Example with both internal channels enabled.
> > > + #
> > > + # When interfacing with a third party tuner device with two data pins as
> shown
> > > + # below.
> > > + #
> > > + # +---------------------+ +---------------------+
> > > + # | |-----SCK------->|CLK |
> > > + # | Master |-----SS-------->|SYNC DRIFn (slave) |
> > > + # | |-----SD0------->|D0 |
> > > + # | |-----SD1------->|D1 |
> > > + # +---------------------+ +---------------------+
> > > + - |
> > > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h>
> > > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > > + #include <dt-bindings/power/r8a7795-sysc.h>
> > > +
> > > + soc {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > +
> > > + drif00: rif@e6f40000 {
> > > + compatible = "renesas,r8a7795-drif",
> > > + "renesas,rcar-gen3-drif";
> > > + reg = <0 0xe6f40000 0 0x64>;
> > > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD 515>;
> > > + clock-names = "fck";
> > > + dmas = <&dmac1 0x20>, <&dmac2 0x20>;
> > > + dma-names = "rx", "rx";
> > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > + renesas,bonding = <&drif01>;
> > > + resets = <&cpg 515>;
> > > + renesas,primary-bond;
> > > + pinctrl-0 = <&drif0_pins>;
> > > + pinctrl-names = "default";
> > > + port {
> > > + drif0_ep: endpoint {
> > > + remote-endpoint = <&tuner_ep>;
> > > + };
> > > + };
> > > + };
> > > +
> > > + drif01: rif@e6f50000 {
> > > + compatible = "renesas,r8a7795-drif",
> > > + "renesas,rcar-gen3-drif";
> > > + reg = <0 0xe6f50000 0 0x64>;
> > > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD 514>;
> > > + clock-names = "fck";
> > > + dmas = <&dmac1 0x22>, <&dmac2 0x22>;
> > > + dma-names = "rx", "rx";
> > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > + renesas,bonding = <&drif00>;
> > > + resets = <&cpg 514>;
> > > + };
> > > + };
> > > +
> > > + # Example with internal channel 1 alone enabled.
> > > + #
> > > + # When interfacing with a third party tuner device with one data pin as
> shown
> > > + # below.
> > > + #
> > > + # +---------------------+ +---------------------+
> > > + # | |-----SCK------->|CLK |
> > > + # | Master |-----SS-------->|SYNC DRIFn (slave) |
> > > + # | | |D0 (unused) |
> > > + # | |-----SD-------->|D1 |
> > > + # +---------------------+ +---------------------+
> > > + - |
> > > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h>
> > > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > > + #include <dt-bindings/power/r8a7795-sysc.h>
> > > +
> > > + soc {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > +
> > > + drif10: rif@e6f60000 {
> > > + compatible = "renesas,r8a7795-drif",
> > > + "renesas,rcar-gen3-drif";
> > > + reg = <0 0xe6f60000 0 0x64>;
> > > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD 513>;
> > > + clock-names = "fck";
> > > + dmas = <&dmac1 0x24>, <&dmac2 0x24>;
> > > + dma-names = "rx", "rx";
> > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > + resets = <&cpg 513>;
> > > + renesas,bonding = <&drif11>;
> > > + };
> > > +
> > > + drif11: rif@e6f70000 {
> > > + compatible = "renesas,r8a7795-drif",
> > > + "renesas,rcar-gen3-drif";
> > > + reg = <0 0xe6f70000 0 0x64>;
> > > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD 512>;
> > > + clock-names = "fck";
> > > + dmas = <&dmac1 0x26>, <&dmac2 0x26>;
> > > + dma-names = "rx", "rx";
> > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > > + resets = <&cpg 512>;
> > > + renesas,bonding = <&drif10>;
> > > + pinctrl-0 = <&drif1_pins>;
> > > + pinctrl-names = "default";
> > > + port {
> > > + drif1_ep: endpoint {
> > > + remote-endpoint = <&tuner_ep1>;
> > > + sync-active = <0>;
> > > + };
> > > + };
> > > + };
> > > + };
> > > +...
> > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > index 9f49e5ac90d8..3e2a1cad3749 100644
> > > --- a/MAINTAINERS
> > > +++ b/MAINTAINERS
> > > @@ -10903,7 +10903,7 @@ L:linux-media@vger.kernel.org
> > > L:linux-renesas-soc@vger.kernel.org
> > > S:Supported
> > > T:git git://linuxtv.org/media_tree.git
> > > -F:Documentation/devicetree/bindings/media/renesas,drif.txt
> > > +F:Documentation/devicetree/bindings/media/renesas,drif.yaml
> > > F:drivers/media/platform/rcar_drif.c
> > >
> > > MEDIA DRIVERS FOR RENESAS - FCP
>
> --
> Regards,
>
> Laurent Pinchart

Renesas Electronics Europe GmbH, Geschaeftsfuehrer/President: Carsten Jauch, Sitz der Gesellschaft/Registered office: Duesseldorf, Arcadiastrasse 10, 40472 Duesseldorf, Germany, Handelsregister/Commercial Register: Duesseldorf, HRB 3708 USt-IDNr./Tax identification no.: DE 119353406 WEEE-Reg.-Nr./WEEE reg. no.: DE 14978647