Re: [PATCH] staging: rtl8723bs: align comments

Fabio Aiuto
2021-03-10T22:46:47Z

On Wed, Mar 10, 2021 at 10:27:53PM +0000, Eric Curtin wrote:
> Hi Fabio,
>
> > I am sorry, I fear I don't understand, checkpatch.sh script says the patch is ok.
> > Where have I to add a ' ' (a blank?)?
> >
> > thank you,
> >
> > fabio
> >
>
> I'm only responding to this because this email is doing a very good job
> of avoiding my filters somehow :) I think what Greg means is:
>
> Change this:
>
> /*
> -op_mode
> -Set to 0 (HT pure) under the following conditions
> - - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
> - - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
> -Set to 1 (HT non-member protection) if there may be non-HT STAs
> - in both the primary and the secondary channel
> -Set to 2 if only HT STAs are associated in BSS,
> - however and at least one 20 MHz HT STA is associated
> -Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
> - (currently non-GF HT station is considered as non-HT STA also)
> -*/
> + *op_mode
> + *Set to 0 (HT pure) under the following conditions
> + * - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
> + * - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
> + *Set to 1 (HT non-member protection) if there may be non-HT STAs
> + * in both the primary and the secondary channel
> + *Set to 2 if only HT STAs are associated in BSS,
> + * however and at least one 20 MHz HT STA is associated
> + *Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
> + * (currently non-GF HT station is considered as non-HT STA also)
> + */
>
> to this:
>
> /*
> -op_mode
> -Set to 0 (HT pure) under the following conditions
> - - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
> - - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
> -Set to 1 (HT non-member protection) if there may be non-HT STAs
> - in both the primary and the secondary channel
> -Set to 2 if only HT STAs are associated in BSS,
> - however and at least one 20 MHz HT STA is associated
> -Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
> - (currently non-GF HT station is considered as non-HT STA also)
> -*/
> + * op_mode
> + * Set to 0 (HT pure) under the following conditions
> + * - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
> + * - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
> + * Set to 1 (HT non-member protection) if there may be non-HT STAs
> + * in both the primary and the secondary channel
> + * Set to 2 if only HT STAs are associated in BSS,
> + * however and at least one 20 MHz HT STA is associated
> + * Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
> + * (currently non-GF HT station is considered as non-HT STA also)
> + * /
>
> Like Dan said, you need a space after the '*'/
>
> Is mise le meas/Regards,
>
> Eric Curtin
>
> Check out this charity that's close to my heart:
>
> https://www.idonate.ie/fundraiser/11394438_peak-for-pat.html
> https://www.facebook.com/Peak-for-Pat-104470678280309
> https://www.instagram.com/peakforpat/

thank you, Eric :)