From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: Bhaumik Bhatt <bbhatt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org, hemantk@codeaurora.org,
linux-kernel@vger.kernel.org, loic.poulain@linaro.org,
quic_jhugo@quicinc.com
Subject: Re: [PATCH v1 2/2] bus: mhi: core: Optimize and update MMIO register write method
Date: Thu, 19 Aug 2021 22:33:01 +0530 [thread overview]
Message-ID: <20210819170301.GF200135@thinkpad> (raw)
In-Reply-To: <1629330634-36465-3-git-send-email-bbhatt@codeaurora.org>
On Wed, Aug 18, 2021 at 04:50:34PM -0700, Bhaumik Bhatt wrote:
> As of now, MMIO writes done after ready state transition use the
> mhi_write_reg_field() API even though the whole register is being
> written in most cases. Optimize this process by using mhi_write_reg()
> API instead for those writes and use the mhi_write_reg_field()
> API for MHI config registers only.
>
> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> drivers/bus/mhi/core/init.c | 64 ++++++++++++++++++++++-----------------------
> 1 file changed, 31 insertions(+), 33 deletions(-)
>
> diff --git a/drivers/bus/mhi/core/init.c b/drivers/bus/mhi/core/init.c
> index 0917465..e4be171 100644
> --- a/drivers/bus/mhi/core/init.c
> +++ b/drivers/bus/mhi/core/init.c
> @@ -433,75 +433,65 @@ int mhi_init_mmio(struct mhi_controller *mhi_cntrl)
> struct device *dev = &mhi_cntrl->mhi_dev->dev;
> struct {
> u32 offset;
> - u32 mask;
> - u32 shift;
> u32 val;
> } reg_info[] = {
> {
> - CCABAP_HIGHER, U32_MAX, 0,
> + CCABAP_HIGHER,
> upper_32_bits(mhi_cntrl->mhi_ctxt->chan_ctxt_addr),
> },
> {
> - CCABAP_LOWER, U32_MAX, 0,
> + CCABAP_LOWER,
> lower_32_bits(mhi_cntrl->mhi_ctxt->chan_ctxt_addr),
> },
> {
> - ECABAP_HIGHER, U32_MAX, 0,
> + ECABAP_HIGHER,
> upper_32_bits(mhi_cntrl->mhi_ctxt->er_ctxt_addr),
> },
> {
> - ECABAP_LOWER, U32_MAX, 0,
> + ECABAP_LOWER,
> lower_32_bits(mhi_cntrl->mhi_ctxt->er_ctxt_addr),
> },
> {
> - CRCBAP_HIGHER, U32_MAX, 0,
> + CRCBAP_HIGHER,
> upper_32_bits(mhi_cntrl->mhi_ctxt->cmd_ctxt_addr),
> },
> {
> - CRCBAP_LOWER, U32_MAX, 0,
> + CRCBAP_LOWER,
> lower_32_bits(mhi_cntrl->mhi_ctxt->cmd_ctxt_addr),
> },
> {
> - MHICFG, MHICFG_NER_MASK, MHICFG_NER_SHIFT,
> - mhi_cntrl->total_ev_rings,
> - },
> - {
> - MHICFG, MHICFG_NHWER_MASK, MHICFG_NHWER_SHIFT,
> - mhi_cntrl->hw_ev_rings,
> - },
> - {
> - MHICTRLBASE_HIGHER, U32_MAX, 0,
> + MHICTRLBASE_HIGHER,
> upper_32_bits(mhi_cntrl->iova_start),
> },
> {
> - MHICTRLBASE_LOWER, U32_MAX, 0,
> + MHICTRLBASE_LOWER,
> lower_32_bits(mhi_cntrl->iova_start),
> },
> {
> - MHIDATABASE_HIGHER, U32_MAX, 0,
> + MHIDATABASE_HIGHER,
> upper_32_bits(mhi_cntrl->iova_start),
> },
> {
> - MHIDATABASE_LOWER, U32_MAX, 0,
> + MHIDATABASE_LOWER,
> lower_32_bits(mhi_cntrl->iova_start),
> },
> {
> - MHICTRLLIMIT_HIGHER, U32_MAX, 0,
> + MHICTRLLIMIT_HIGHER,
> upper_32_bits(mhi_cntrl->iova_stop),
> },
> {
> - MHICTRLLIMIT_LOWER, U32_MAX, 0,
> + MHICTRLLIMIT_LOWER,
> lower_32_bits(mhi_cntrl->iova_stop),
> },
> {
> - MHIDATALIMIT_HIGHER, U32_MAX, 0,
> + MHIDATALIMIT_HIGHER,
> upper_32_bits(mhi_cntrl->iova_stop),
> },
> {
> - MHIDATALIMIT_LOWER, U32_MAX, 0,
> + MHIDATALIMIT_LOWER,
> lower_32_bits(mhi_cntrl->iova_stop),
> },
> - { 0, 0, 0 }
> + {0, 0}
> };
>
> dev_dbg(dev, "Initializing MHI registers\n");
> @@ -544,14 +534,22 @@ int mhi_init_mmio(struct mhi_controller *mhi_cntrl)
> mhi_cntrl->mhi_cmd[PRIMARY_CMD_RING].ring.db_addr = base + CRDB_LOWER;
>
> /* Write to MMIO registers */
> - for (i = 0; reg_info[i].offset; i++) {
> - ret = mhi_write_reg_field(mhi_cntrl, base, reg_info[i].offset,
> - reg_info[i].mask, reg_info[i].shift,
> - reg_info[i].val);
> - if (ret) {
> - dev_err(dev, "Unable to write to MMIO registers");
> - return ret;
> - }
> + for (i = 0; reg_info[i].offset; i++)
> + mhi_write_reg(mhi_cntrl, base, reg_info[i].offset,
> + reg_info[i].val);
> +
> + ret = mhi_write_reg_field(mhi_cntrl, base, MHICFG, MHICFG_NER_MASK,
> + MHICFG_NER_SHIFT, mhi_cntrl->total_ev_rings);
> + if (ret) {
> + dev_err(dev, "Unable to read MHICFG register\n");
> + return ret;
> + }
> +
> + ret = mhi_write_reg_field(mhi_cntrl, base, MHICFG, MHICFG_NHWER_MASK,
> + MHICFG_NHWER_SHIFT, mhi_cntrl->hw_ev_rings);
> + if (ret) {
> + dev_err(dev, "Unable to read MHICFG register\n");
> + return ret;
> }
>
> return 0;
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
prev parent reply other threads:[~2021-08-19 17:03 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-18 23:50 [PATCH v1 0/2] MHI MMIO register write updates Bhaumik Bhatt
2021-08-18 23:50 ` [PATCH v1 1/2] bus: mhi: core: Bail on writing register fields if read fails Bhaumik Bhatt
2021-08-19 1:40 ` Hemant Kumar
2021-08-19 14:05 ` Jeffrey Hugo
2021-08-19 2:50 ` kernel test robot
2021-08-19 17:02 ` Manivannan Sadhasivam
2021-08-18 23:50 ` [PATCH v1 2/2] bus: mhi: core: Optimize and update MMIO register write method Bhaumik Bhatt
2021-08-19 1:41 ` Hemant Kumar
2021-08-19 14:05 ` Jeffrey Hugo
2021-08-19 17:03 ` Manivannan Sadhasivam [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210819170301.GF200135@thinkpad \
--to=manivannan.sadhasivam@linaro.org \
--cc=bbhatt@codeaurora.org \
--cc=hemantk@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=loic.poulain@linaro.org \
--cc=quic_jhugo@quicinc.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox