From: Richard Fitzgerald <rf@opensource.cirrus.com>
To: <broonie@kernel.org>
Cc: <alsa-devel@alsa-project.org>, <linux-kernel@vger.kernel.org>,
<patches@opensource.cirrus.com>,
Richard Fitzgerald <rf@opensource.cirrus.com>
Subject: [PATCH 00/16] ASoC: cs42l42: Collection of bugfixes
Date: Fri, 15 Oct 2021 14:36:03 +0100 [thread overview]
Message-ID: <20211015133619.4698-1-rf@opensource.cirrus.com> (raw)
This patch set contains various bugfixes for the cs42l42 codec
driver.
Patches marked "Fixes" will apply cleanly to the patch that first
introduced the bug.
Patches NOT marked "Fixes" will not apply cleanly to the point
the bug was first introduced and/or the bug is not having
sufficient impact to risk churning older code versions.
Richard Fitzgerald (16):
ASoC: cs42l42: Don't reconfigure the PLL while it is running
ASoC: cs42l42: Always configure both ASP TX channels
ASoC: cs42l42: Correct some register default values
ASoC: cs42l42: Don't set defaults for volatile registers
ASoC: cs42l42: Defer probe if request_threaded_irq() returns
EPROBE_DEFER
ASoC: cs42l42: Reset GPIO is mandatory
ASoC: cs42l42: Correct power-up sequence to match datasheet
ASoC: cs42l42: Reset and power-down on driver remove()
ASoC: cs42l42: Prevent NULL pointer deref in interrupt handler
ASoC: cs42l42: Don't claim to support 192k
ASoC: cs42l42: Use PLL for SCLK > 12.288MHz
ASoC: cs42l42: Allow time for HP/ADC to power-up after enable
ASoC: cs42l42: Set correct SRC MCLK
ASoC: cs42l42: Mark OSC_SWITCH_STATUS register volatile
ASoC: cs42l42: Fix WARN in remove() if running without an interrupt
ASoC: cs42l42: Always enable TS_PLUG and TS_UNPLUG interrupts
sound/soc/codecs/cs42l42.c | 282 +++++++++++++++++++++++++--------------------
sound/soc/codecs/cs42l42.h | 9 +-
2 files changed, 160 insertions(+), 131 deletions(-)
--
2.11.0
next reply other threads:[~2021-10-15 13:37 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-15 13:36 Richard Fitzgerald [this message]
2021-10-15 13:36 ` [PATCH 01/16] ASoC: cs42l42: Don't reconfigure the PLL while it is running Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 02/16] ASoC: cs42l42: Always configure both ASP TX channels Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 03/16] ASoC: cs42l42: Correct some register default values Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 04/16] ASoC: cs42l42: Don't set defaults for volatile registers Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 05/16] ASoC: cs42l42: Defer probe if request_threaded_irq() returns EPROBE_DEFER Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 06/16] ASoC: cs42l42: Reset GPIO is mandatory Richard Fitzgerald
2021-10-15 14:30 ` Mark Brown
2021-10-15 13:36 ` [PATCH 07/16] ASoC: cs42l42: Correct power-up sequence to match datasheet Richard Fitzgerald
2021-10-15 15:02 ` Mark Brown
2021-10-15 13:36 ` [PATCH 08/16] ASoC: cs42l42: Reset and power-down on driver remove() Richard Fitzgerald
2021-10-15 15:04 ` Mark Brown
2021-10-15 13:36 ` [PATCH 09/16] ASoC: cs42l42: Prevent NULL pointer deref in interrupt handler Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 10/16] ASoC: cs42l42: Don't claim to support 192k Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 11/16] ASoC: cs42l42: Use PLL for SCLK > 12.288MHz Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 12/16] ASoC: cs42l42: Allow time for HP/ADC to power-up after enable Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 13/16] ASoC: cs42l42: Set correct SRC MCLK Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 14/16] ASoC: cs42l42: Mark OSC_SWITCH_STATUS register volatile Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 15/16] ASoC: cs42l42: Fix WARN in remove() if running without an interrupt Richard Fitzgerald
2021-10-15 13:36 ` [PATCH 16/16] ASoC: cs42l42: Always enable TS_PLUG and TS_UNPLUG interrupts Richard Fitzgerald
2021-10-15 19:42 ` (subset) [PATCH 00/16] ASoC: cs42l42: Collection of bugfixes Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211015133619.4698-1-rf@opensource.cirrus.com \
--to=rf@opensource.cirrus.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@opensource.cirrus.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox