From: Vinod Koul <vkoul@kernel.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, Vinod Koul <vkoul@kernel.org>,
Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 03/15] arm64: dts: qcom: sm8450: Add tlmm nodes
Date: Wed, 1 Dec 2021 12:59:03 +0530 [thread overview]
Message-ID: <20211201072915.3969178-4-vkoul@kernel.org> (raw)
In-Reply-To: <20211201072915.3969178-1-vkoul@kernel.org>
Add tlmm node found in SM8450 SoC and uart pin configuration
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 29 ++++++++++++++++++++++++++++
1 file changed, 29 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index d838283bde4b..f0b9e80238a2 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -343,6 +343,8 @@ uart7: serial@99c000 {
reg = <0 0x0099c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_default_state>;
interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
@@ -366,6 +368,33 @@ pdc: interrupt-controller@b220000 {
interrupt-controller;
};
+ tlmm: pinctrl@f100000 {
+ compatible = "qcom,sm8450-tlmm";
+ reg = <0 0x0f100000 0 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 211>;
+ wakeup-parent = <&pdc>;
+
+ qup_uart7_default_state: qup-uart3-default-state {
+ rx {
+ pins = "gpio26";
+ function = "qup7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ tx {
+ pins = "gpio27";
+ function = "qup7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+ };
+
intc: interrupt-controller@17100000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
--
2.31.1
next prev parent reply other threads:[~2021-12-01 7:29 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-01 7:29 [PATCH 00/15] arm64: dts: qcom: Add support for SM8450 SoC and QRD board Vinod Koul
2021-12-01 7:29 ` [PATCH 01/15] arm64: dts: qcom: Add base SM8450 DTSI Vinod Koul
2021-12-01 15:03 ` Konrad Dybcio
2021-12-06 5:39 ` Vinod Koul
2021-12-07 14:35 ` Bjorn Andersson
2021-12-07 14:53 ` Bjorn Andersson
2021-12-01 7:29 ` [PATCH 02/15] arm64: dts: qcom: Add base SM8450 QRD DTS Vinod Koul
2021-12-01 15:05 ` Konrad Dybcio
2021-12-01 7:29 ` Vinod Koul [this message]
2021-12-07 14:37 ` [PATCH 03/15] arm64: dts: qcom: sm8450: Add tlmm nodes Bjorn Andersson
2021-12-01 7:29 ` [PATCH 04/15] arm64: dts: qcom: sm8450-qrd: Add reserved gpio range for QRD Vinod Koul
2021-12-01 15:07 ` Konrad Dybcio
2021-12-06 5:53 ` Vinod Koul
2021-12-07 14:56 ` Bjorn Andersson
2021-12-01 7:29 ` [PATCH 05/15] arm64: dts: qcom: sm8450: Add reserved memory nodes Vinod Koul
2021-12-01 15:11 ` Konrad Dybcio
2021-12-06 5:42 ` Vinod Koul
2021-12-01 7:29 ` [PATCH 06/15] arm64: dts: qcom: sm8450: add smmu nodes Vinod Koul
2021-12-01 15:13 ` Konrad Dybcio
2021-12-01 7:29 ` [PATCH 07/15] arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes Vinod Koul
2021-12-01 15:14 ` Konrad Dybcio
2021-12-01 7:29 ` [PATCH 09/15] arm64: dts: qcom: sm8450-qrd: enable ufs nodes Vinod Koul
2021-12-01 15:18 ` Konrad Dybcio
2021-12-06 5:58 ` Vinod Koul
2021-12-07 15:01 ` Bjorn Andersson
2021-12-01 7:29 ` [PATCH 10/15] arm64: dts: qcom: sm8450: add interconnect nodes Vinod Koul
2021-12-01 15:20 ` Konrad Dybcio
2021-12-06 6:12 ` Vinod Koul
2021-12-01 7:29 ` [PATCH 11/15] arm64: dts: qcom: sm8450: add spmi node Vinod Koul
2021-12-01 15:22 ` Konrad Dybcio
2021-12-01 7:29 ` [PATCH 12/15] arm64: dts: qcom: sm8450-qrd: include pmic files Vinod Koul
2021-12-01 15:23 ` Konrad Dybcio
2021-12-07 15:05 ` Bjorn Andersson
2021-12-07 15:51 ` Vinod Koul
2021-12-01 7:29 ` [PATCH 13/15] arm64: dts: qcom: sm8450: Add rpmhpd node Vinod Koul
2021-12-01 15:24 ` Konrad Dybcio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211201072915.3969178-4-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox