[PATCH v2 5/9] regulator: rpi-panel: Convert to drive lines directly

[Detlev Casanova <detlev.casanova@collabora.com>]

From: Dave Stevenson <dave.stevenson@raspberrypi.com>

The Atmel was doing a load of automatic sequencing of
control lines, however it was combining the touch controller's
reset with the bridge/panel control.

Change to control the control signals directly rather than
through the automatic POWERON control.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
---
 .../regulator/rpi-panel-attiny-regulator.c    | 111 ++++++++++--------
 1 file changed, 60 insertions(+), 51 deletions(-)

diff --git a/drivers/regulator/rpi-panel-attiny-regulator.c b/drivers/regulator/rpi-panel-attiny-regulator.c
index b3629a1e0e50..995915ca4a9b 100644
--- a/drivers/regulator/rpi-panel-attiny-regulator.c
+++ b/drivers/regulator/rpi-panel-attiny-regulator.c
@@ -21,11 +21,28 @@
 /* I2C registers of the Atmel microcontroller. */
 #define REG_ID		0x80
 #define REG_PORTA	0x81
-#define REG_PORTA_HF	BIT(2)
-#define REG_PORTA_VF	BIT(3)
 #define REG_PORTB	0x82
+#define REG_PORTC	0x83
 #define REG_POWERON	0x85
 #define REG_PWM		0x86
+#define REG_ADDR_L	0x8c
+#define REG_ADDR_H	0x8d
+#define REG_WRITE_DATA_H	0x90
+#define REG_WRITE_DATA_L	0x91
+
+#define PA_LCD_DITHB		BIT(0)
+#define PA_LCD_MODE		BIT(1)
+#define PA_LCD_LR		BIT(2)
+#define PA_LCD_UD		BIT(3)
+
+#define PB_BRIDGE_PWRDNX_N	BIT(0)
+#define PB_LCD_VCC_N		BIT(1)
+#define PB_LCD_MAIN		BIT(7)
+
+#define PC_LED_EN		BIT(0)
+#define PC_RST_TP_N		BIT(1)
+#define PC_RST_LCD_N		BIT(2)
+#define PC_RST_BRIDGE_N		BIT(3)
 
 struct attiny_lcd {
 	/* lock to serialise overall accesses to the Atmel */
@@ -37,99 +54,91 @@ static const struct regmap_config attiny_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
 	.disable_locking = 1,
-	.max_register = REG_PWM,
+	.max_register = REG_WRITE_DATA_L,
 	.cache_type = REGCACHE_NONE,
 };
 
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
-	struct mutex *lock = rdev_get_drvdata(rdev);
-	unsigned int data;
-	int ret, i;
-
-	mutex_lock(lock);
-
-	regmap_write(rdev->regmap, REG_POWERON, 1);
-	msleep(80);
+	struct attiny_lcd *state = rdev_get_drvdata(rdev);
 
-	/* Wait for nPWRDWN to go low to indicate poweron is done. */
-	for (i = 0; i < 20; i++) {
-		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
-		if (!ret) {
-			if (data & BIT(0))
-				break;
-		}
-		usleep_range(10000, 12000);
-	}
-	usleep_range(10000, 12000);
+	mutex_lock(&state->lock);
 
-	if (ret)
-		pr_err("%s: regmap_read_poll_timeout failed %d\n", __func__, ret);
+	/* Ensure bridge, and tp stay in reset */
+	regmap_write(rdev->regmap, REG_PORTC, 0);
+	usleep_range(5000, 10000);
 
 	/* Default to the same orientation as the closed source
 	 * firmware used for the panel.  Runtime rotation
 	 * configuration will be supported using VC4's plane
 	 * orientation bits.
 	 */
-	regmap_write(rdev->regmap, REG_PORTA, BIT(2));
+	regmap_write(rdev->regmap, REG_PORTA, PA_LCD_LR);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTB, PB_LCD_MAIN);
+	usleep_range(5000, 10000);
+	/* Bring controllers out of reset */
+	regmap_write(rdev->regmap, REG_PORTC,
+		     PC_LED_EN | PC_RST_BRIDGE_N | PC_RST_LCD_N | PC_RST_TP_N);
+
+	msleep(80);
+
+	regmap_write(rdev->regmap, REG_ADDR_H, 0x04);
+	usleep_range(5000, 8000);
+	regmap_write(rdev->regmap, REG_ADDR_L, 0x7c);
+	usleep_range(5000, 8000);
+	regmap_write(rdev->regmap, REG_WRITE_DATA_H, 0x00);
+	usleep_range(5000, 8000);
+	regmap_write(rdev->regmap, REG_WRITE_DATA_L, 0x00);
+
+	msleep(100);
 
-	mutex_unlock(lock);
+	mutex_unlock(&state->lock);
 
 	return 0;
 }
 
 static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 {
-	struct mutex *lock = rdev_get_drvdata(rdev);
+	struct attiny_lcd *state = rdev_get_drvdata(rdev);
 
-	mutex_lock(lock);
+	mutex_lock(&state->lock);
 
 	regmap_write(rdev->regmap, REG_PWM, 0);
-	regmap_write(rdev->regmap, REG_POWERON, 0);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTA, 0);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTB, PB_LCD_VCC_N);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTC, 0);
 	msleep(30);
 
-	mutex_unlock(lock);
+	mutex_unlock(&state->lock);
 
 	return 0;
 }
 
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
-	struct mutex *lock = rdev_get_drvdata(rdev);
+	struct attiny_lcd *state = rdev_get_drvdata(rdev);
 	unsigned int data;
 	int ret, i;
 
-	mutex_lock(lock);
-
-	for (i = 0; i < 10; i++) {
-		ret = regmap_read(rdev->regmap, REG_POWERON, &data);
-		if (!ret)
-			break;
-		usleep_range(10000, 12000);
-	}
-	if (ret < 0) {
-		mutex_unlock(lock);
-		return ret;
-	}
-
-	if (!(data & BIT(0))) {
-		mutex_unlock(lock);
-		return 0;
-	}
+	mutex_lock(&state->lock);
 
 	for (i = 0; i < 10; i++) {
-		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		ret = regmap_read(rdev->regmap, REG_PORTC, &data);
 		if (!ret)
 			break;
 		usleep_range(10000, 12000);
 	}
 
-	mutex_unlock(lock);
+	mutex_unlock(&state->lock);
 
 	if (ret < 0)
 		return ret;
 
-	return data & BIT(0);
+	return data & PC_RST_BRIDGE_N;
 }
 
 static const struct regulator_init_data attiny_regulator_default = {
@@ -256,7 +265,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	config.regmap = regmap;
 	config.of_node = i2c->dev.of_node;
 	config.init_data = &attiny_regulator_default;
-	config.driver_data = &state->lock;
+	config.driver_data = state;
 
 	rdev = devm_regulator_register(&i2c->dev, &attiny_regulator, &config);
 	if (IS_ERR(rdev)) {
-- 
2.34.1