[PATCH v2 1/2] serial: 8250_lpss: Balance reference count for PCI DMA device

[Andy Shevchenko <andriy.shevchenko@linux.intel.com>]

The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().

Fixes: 9a1870ce812e ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf3dc1 ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
v2: made sure we bump reference count only on success (Jiri)
 drivers/tty/serial/8250/8250_lpss.c | 28 ++++++++++++++++++++++------
 1 file changed, 22 insertions(+), 6 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c
index d3bafec7619d..0f5af061e0b4 100644
--- a/drivers/tty/serial/8250/8250_lpss.c
+++ b/drivers/tty/serial/8250/8250_lpss.c
@@ -117,8 +117,7 @@ static int byt_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 {
 	struct dw_dma_slave *param = &lpss->dma_param;
 	struct pci_dev *pdev = to_pci_dev(port->dev);
-	unsigned int dma_devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0);
-	struct pci_dev *dma_dev = pci_get_slot(pdev->bus, dma_devfn);
+	struct pci_dev *dma_dev;
 
 	switch (pdev->device) {
 	case PCI_DEVICE_ID_INTEL_BYT_UART1:
@@ -137,6 +136,8 @@ static int byt_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 		return -EINVAL;
 	}
 
+	dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
+
 	param->dma_dev = &dma_dev->dev;
 	param->m_master = 0;
 	param->p_master = 1;
@@ -152,6 +153,14 @@ static int byt_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 	return 0;
 }
 
+static void byt_serial_exit(struct lpss8250 *lpss)
+{
+	struct dw_dma_slave *param = &lpss->dma_param;
+
+	/* Paired with pci_get_slot() in the byt_serial_setup() above */
+	put_device(param->dma_dev);
+}
+
 static int ehl_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 {
 	struct uart_8250_dma *dma = &lpss->data.dma;
@@ -170,6 +179,13 @@ static int ehl_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 	return 0;
 }
 
+static void ehl_serial_exit(struct lpss8250 *lpss)
+{
+	struct uart_8250_port *up = serial8250_get_port(lpss->data.line);
+
+	up->dma = NULL;
+}
+
 #ifdef CONFIG_SERIAL_8250_DMA
 static const struct dw_dma_platform_data qrk_serial_dma_pdata = {
 	.nr_channels = 2,
@@ -344,8 +360,7 @@ static int lpss8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	return 0;
 
 err_exit:
-	if (lpss->board->exit)
-		lpss->board->exit(lpss);
+	lpss->board->exit(lpss);
 	pci_free_irq_vectors(pdev);
 	return ret;
 }
@@ -356,8 +371,7 @@ static void lpss8250_remove(struct pci_dev *pdev)
 
 	serial8250_unregister_port(lpss->data.line);
 
-	if (lpss->board->exit)
-		lpss->board->exit(lpss);
+	lpss->board->exit(lpss);
 	pci_free_irq_vectors(pdev);
 }
 
@@ -365,12 +379,14 @@ static const struct lpss8250_board byt_board = {
 	.freq = 100000000,
 	.base_baud = 2764800,
 	.setup = byt_serial_setup,
+	.exit = byt_serial_exit,
 };
 
 static const struct lpss8250_board ehl_board = {
 	.freq = 200000000,
 	.base_baud = 12500000,
 	.setup = ehl_serial_setup,
+	.exit = ehl_serial_exit,
 };
 
 static const struct lpss8250_board qrk_board = {
-- 
2.34.1