[PATCH v1 12/17] arm: dts: imx6qdl-vicut1.dtsi: Move some node out to DTS files

Oleksij Rempel
2022-04-12T09:28:39Z

This commit will finally make this file identical to imx6qdl-victgo.dtsi.
All nodes that are removed here are added as-is to the DTS files that
include this file.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-vicut1.dts | 122 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-vicut1.dts | 122 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 120 -------------------------
arch/arm/boot/dts/imx6qp-vicutp.dts | 122 ++++++++++++++++++++++++++
4 files changed, 366 insertions(+), 120 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts
index 174fd913bf96..c6a904bbed01 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1 Board";
compatible = "kvg,vicut1", "fsl,imx6dl";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <&reg_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index e6c5d3cb48d7..8b228d5fc4a3 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <&reg_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index 6c943ca950f4..2a86136a04e8 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -70,20 +70,6 @@ counter-2 {
gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
};

- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
- autorepeat;
-
- power {
- label = "Power Button";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- wakeup-source;
- };
- };
-
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -111,18 +97,6 @@ led-2 {
};
};

- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
- power-supply = <&reg_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -231,38 +205,6 @@ flash@0 {
};
};

-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy@0 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&gpio1 {
- gpio-line-names =
- "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
- "CAM2_MIRROR", "", "", "SMBALERT",
- "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
- "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "ETH_MDIO", "",
- "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
-};
-
&gpio2 {
gpio-line-names =
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
@@ -282,38 +224,6 @@ &gpio3 {
"YACO_RESET";
};

-&gpio4 {
- gpio-line-names =
- "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
- "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
- "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
- "HITCH_IN_OUT",
- "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
- "ISB_LED";
-};
-
-&gpio5 {
- gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
- "I2S_BITCLK", "I2S_DOUT",
- "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
- "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
- gpio-line-names =
- "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
- "ITU656_D6", "ITU656_D7", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
- "RGMII_TD3",
- "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
- "RGMII_RD2", "RGMII_RD3", "", "";
-};
-
&gpio7 {
gpio-line-names =
"EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
@@ -589,36 +499,6 @@ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
>;
};

- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_gpiokeys: gpiokeygrp {
- fsl,pins = <
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- >;
- };
-
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts
index 7bad7ca6b12e..31c748e9d92f 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@@ -10,4 +10,126 @@
/ {
model = "Kverneland UT1P Board";
compatible = "kvg,vicutp", "fsl,imx6qp";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+ autorepeat;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+ power-supply = <&reg_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+ "CAM2_MIRROR", "", "", "SMBALERT",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+ "ISB_LED";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
+ "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+ "YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+ "RGMII_TD3",
+ "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+ "RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeygrp {
+ fsl,pins = <
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ >;
+ };
};
--
2.30.2