[PATCH v2 net-next 2/2] net: phy: micrel: Adding LED feature for LAN8814 PHY

Divya Koppera
2022-06-29T08:58:37Z

LED support for extended mode where
LED 1: Enhanced Mode 5 (10M/1000M/Activity)
LED 2: Enhanced Mode 4 (100M/1000M/Activity)

By default it supports KSZ9031 LED mode

Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
---
v1 -> v2:
- No changes

drivers/net/phy/micrel.c | 71 +++++++++++++++++++++++++++++++---------
1 file changed, 56 insertions(+), 15 deletions(-)

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 22139901f01c..297e58d49159 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -209,6 +209,9 @@
#define PTP_TSU_INT_STS_PTP_RX_TS_OVRFL_INT_ BIT(1)
#define PTP_TSU_INT_STS_PTP_RX_TS_EN_ BIT(0)

+#define LAN8814_LED_CTRL_1 0x0
+#define LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_ BIT(6)
+
/* PHY Control 1 */
#define MII_KSZPHY_CTRL_1 0x1e
#define KSZ8081_CTRL1_MDIX_STAT BIT(4)
@@ -308,6 +311,10 @@ struct kszphy_priv {
u64 stats[ARRAY_SIZE(kszphy_hw_stats)];
};

+static const struct kszphy_type lan8814_type = {
+ .led_mode_reg = ~LAN8814_LED_CTRL_1,
+};
+
static const struct kszphy_type ksz8021_type = {
.led_mode_reg = MII_KSZPHY_CTRL_2,
.has_broadcast_disable = true,
@@ -1688,6 +1695,30 @@ static int kszphy_suspend(struct phy_device *phydev)
return genphy_suspend(phydev);
}

+static void kszphy_parse_led_mode(struct phy_device *phydev)
+{
+ const struct kszphy_type *type = phydev->drv->driver_data;
+ const struct device_node *np = phydev->mdio.dev.of_node;
+ struct kszphy_priv *priv = phydev->priv;
+ int ret;
+
+ if (type && type->led_mode_reg) {
+ ret = of_property_read_u32(np, "micrel,led-mode",
+ &priv->led_mode);
+
+ if (ret)
+ priv->led_mode = -1;
+
+ if (priv->led_mode > 3) {
+ phydev_err(phydev, "invalid led mode: 0x%02x\n",
+ priv->led_mode);
+ priv->led_mode = -1;
+ }
+ } else {
+ priv->led_mode = -1;
+ }
+}
+
static int kszphy_resume(struct phy_device *phydev)
{
int ret;
@@ -1720,7 +1751,6 @@ static int kszphy_probe(struct phy_device *phydev)
const struct device_node *np = phydev->mdio.dev.of_node;
struct kszphy_priv *priv;
struct clk *clk;
- int ret;

priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
@@ -1730,20 +1760,7 @@ static int kszphy_probe(struct phy_device *phydev)

priv->type = type;

- if (type && type->led_mode_reg) {
- ret = of_property_read_u32(np, "micrel,led-mode",
- &priv->led_mode);
- if (ret)
- priv->led_mode = -1;
-
- if (priv->led_mode > 3) {
- phydev_err(phydev, "invalid led mode: 0x%02x\n",
- priv->led_mode);
- priv->led_mode = -1;
- }
- } else {
- priv->led_mode = -1;
- }
+ kszphy_parse_led_mode(phydev);

clk = devm_clk_get(&phydev->mdio.dev, "rmii-ref");
/* NOTE: clk may be NULL if building without CONFIG_HAVE_CLK */
@@ -2815,8 +2832,23 @@ static int lan8814_ptp_probe_once(struct phy_device *phydev)
return 0;
}

+static void lan8814_setup_led(struct phy_device *phydev, int val)
+{
+ int temp;
+
+ temp = lan8814_read_page_reg(phydev, 5, LAN8814_LED_CTRL_1);
+
+ if (val)
+ temp |= LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_;
+ else
+ temp &= ~LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_;
+
+ lan8814_write_page_reg(phydev, 5, LAN8814_LED_CTRL_1, temp);
+}
+
static int lan8814_config_init(struct phy_device *phydev)
{
+ struct kszphy_priv *lan8814 = phydev->priv;
int val;

/* Reset the PHY */
@@ -2850,11 +2882,15 @@ static int lan8814_release_coma_mode(struct phy_device *phydev)
gpiod_set_consumer_name(gpiod, "LAN8814 coma mode");
gpiod_set_value_cansleep(gpiod, 0);

+ if (lan8814->led_mode >= 0)
+ lan8814_setup_led(phydev, lan8814->led_mode);
+
return 0;
}

static int lan8814_probe(struct phy_device *phydev)
{
+ const struct kszphy_type *type = phydev->drv->driver_data;
struct kszphy_priv *priv;
u16 addr;
int err;
@@ -2867,6 +2903,10 @@ static int lan8814_probe(struct phy_device *phydev)

phydev->priv = priv;

+ priv->type = type;
+
+ kszphy_parse_led_mode(phydev);
+
/* Strap-in value for PHY address, below register read gives starting
* phy address value
*/
@@ -3068,6 +3108,7 @@ static struct phy_driver ksphy_driver[] = {
.phy_id_mask = MICREL_PHY_ID_MASK,
.name = "Microchip INDY Gigabit Quad PHY",
.config_init = lan8814_config_init,
+ .driver_data = &lan8814_type,
.probe = lan8814_probe,
.soft_reset = genphy_soft_reset,
.read_status = ksz9031_read_status,
--
2.17.1