From: Anup Patel <apatel@ventanamicro.com>
To: Palmer Dabbelt <palmer@dabbelt.com>,
Paul Walmsley <paul.walmsley@sifive.com>
Cc: Atish Patra <atishp@atishpatra.org>,
Heiko Stuebner <heiko@sntech.de>, Arnd Bergmann <arnd@arndb.de>,
Anup Patel <anup@brainfault.org>,
linux-riscv@lists.infradead.org, linux-kernel@vger.kernel.org,
Andrew Jones <ajones@ventanamicro.com>,
kernel test robot <lkp@intel.com>,
Anup Patel <apatel@ventanamicro.com>,
Conor Dooley <conor.dooley@microchip.com>
Subject: [PATCH v5 1/4] RISC-V: Fix compilation without RISCV_ISA_ZICBOM
Date: Thu, 20 Oct 2022 13:28:43 +0530 [thread overview]
Message-ID: <20221020075846.305576-2-apatel@ventanamicro.com> (raw)
In-Reply-To: <20221020075846.305576-1-apatel@ventanamicro.com>
From: Andrew Jones <ajones@ventanamicro.com>
riscv_cbom_block_size and riscv_init_cbom_blocksize() should always
be available and riscv_init_cbom_blocksize() should always be
invoked, even when compiling without RISCV_ISA_ZICBOM enabled. This
is because disabling RISCV_ISA_ZICBOM means "don't use zicbom
instructions in the kernel" not "pretend there isn't zicbom, even
when there is". When zicbom is available, whether the kernel enables
its use with RISCV_ISA_ZICBOM or not, KVM will offer it to guests.
Ensure we can build KVM and that the block size is initialized even
when compiling without RISCV_ISA_ZICBOM.
Fixes: 8f7e001e0325 ("RISC-V: Clean up the Zicbom block size probing")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
---
arch/riscv/include/asm/cacheflush.h | 8 ------
arch/riscv/mm/cacheflush.c | 38 ++++++++++++++++++++++++++
arch/riscv/mm/dma-noncoherent.c | 41 -----------------------------
3 files changed, 38 insertions(+), 49 deletions(-)
diff --git a/arch/riscv/include/asm/cacheflush.h b/arch/riscv/include/asm/cacheflush.h
index 8a5c246b0a21..f6fbe7042f1c 100644
--- a/arch/riscv/include/asm/cacheflush.h
+++ b/arch/riscv/include/asm/cacheflush.h
@@ -42,16 +42,8 @@ void flush_icache_mm(struct mm_struct *mm, bool local);
#endif /* CONFIG_SMP */
-/*
- * The T-Head CMO errata internally probe the CBOM block size, but otherwise
- * don't depend on Zicbom.
- */
extern unsigned int riscv_cbom_block_size;
-#ifdef CONFIG_RISCV_ISA_ZICBOM
void riscv_init_cbom_blocksize(void);
-#else
-static inline void riscv_init_cbom_blocksize(void) { }
-#endif
#ifdef CONFIG_RISCV_DMA_NONCOHERENT
void riscv_noncoherent_supported(void);
diff --git a/arch/riscv/mm/cacheflush.c b/arch/riscv/mm/cacheflush.c
index 6cb7d96ad9c7..57b40a350420 100644
--- a/arch/riscv/mm/cacheflush.c
+++ b/arch/riscv/mm/cacheflush.c
@@ -3,6 +3,7 @@
* Copyright (C) 2017 SiFive
*/
+#include <linux/of.h>
#include <asm/cacheflush.h>
#ifdef CONFIG_SMP
@@ -86,3 +87,40 @@ void flush_icache_pte(pte_t pte)
flush_icache_all();
}
#endif /* CONFIG_MMU */
+
+unsigned int riscv_cbom_block_size;
+EXPORT_SYMBOL_GPL(riscv_cbom_block_size);
+
+void riscv_init_cbom_blocksize(void)
+{
+ struct device_node *node;
+ unsigned long cbom_hartid;
+ u32 val, probed_block_size;
+ int ret;
+
+ probed_block_size = 0;
+ for_each_of_cpu_node(node) {
+ unsigned long hartid;
+
+ ret = riscv_of_processor_hartid(node, &hartid);
+ if (ret)
+ continue;
+
+ /* set block-size for cbom extension if available */
+ ret = of_property_read_u32(node, "riscv,cbom-block-size", &val);
+ if (ret)
+ continue;
+
+ if (!probed_block_size) {
+ probed_block_size = val;
+ cbom_hartid = hartid;
+ } else {
+ if (probed_block_size != val)
+ pr_warn("cbom-block-size mismatched between harts %lu and %lu\n",
+ cbom_hartid, hartid);
+ }
+ }
+
+ if (probed_block_size)
+ riscv_cbom_block_size = probed_block_size;
+}
diff --git a/arch/riscv/mm/dma-noncoherent.c b/arch/riscv/mm/dma-noncoherent.c
index b0add983530a..d919efab6eba 100644
--- a/arch/riscv/mm/dma-noncoherent.c
+++ b/arch/riscv/mm/dma-noncoherent.c
@@ -8,13 +8,8 @@
#include <linux/dma-direct.h>
#include <linux/dma-map-ops.h>
#include <linux/mm.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
#include <asm/cacheflush.h>
-unsigned int riscv_cbom_block_size;
-EXPORT_SYMBOL_GPL(riscv_cbom_block_size);
-
static bool noncoherent_supported;
void arch_sync_dma_for_device(phys_addr_t paddr, size_t size,
@@ -77,42 +72,6 @@ void arch_setup_dma_ops(struct device *dev, u64 dma_base, u64 size,
dev->dma_coherent = coherent;
}
-#ifdef CONFIG_RISCV_ISA_ZICBOM
-void riscv_init_cbom_blocksize(void)
-{
- struct device_node *node;
- unsigned long cbom_hartid;
- u32 val, probed_block_size;
- int ret;
-
- probed_block_size = 0;
- for_each_of_cpu_node(node) {
- unsigned long hartid;
-
- ret = riscv_of_processor_hartid(node, &hartid);
- if (ret)
- continue;
-
- /* set block-size for cbom extension if available */
- ret = of_property_read_u32(node, "riscv,cbom-block-size", &val);
- if (ret)
- continue;
-
- if (!probed_block_size) {
- probed_block_size = val;
- cbom_hartid = hartid;
- } else {
- if (probed_block_size != val)
- pr_warn("cbom-block-size mismatched between harts %lu and %lu\n",
- cbom_hartid, hartid);
- }
- }
-
- if (probed_block_size)
- riscv_cbom_block_size = probed_block_size;
-}
-#endif
-
void riscv_noncoherent_supported(void)
{
WARN(!riscv_cbom_block_size,
--
2.34.1
next prev parent reply other threads:[~2022-10-20 7:59 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-20 7:58 [PATCH v5 0/4] Add PMEM support for RISC-V Anup Patel
2022-10-20 7:58 ` Anup Patel [this message]
2022-10-21 6:48 ` [PATCH v5 1/4] RISC-V: Fix compilation without RISCV_ISA_ZICBOM Anup Patel
2022-10-20 7:58 ` [PATCH v5 2/4] RISC-V: Fix MEMREMAP_WB for systems with Svpbmt Anup Patel
2022-10-24 19:54 ` Conor Dooley
2022-10-20 7:58 ` [PATCH v5 3/4] RISC-V: Implement arch specific PMEM APIs Anup Patel
2022-10-24 19:52 ` Conor Dooley
2022-11-14 9:02 ` Anup Patel
2022-10-20 7:58 ` [PATCH v5 4/4] RISC-V: Enable PMEM drivers Anup Patel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221020075846.305576-2-apatel@ventanamicro.com \
--to=apatel@ventanamicro.com \
--cc=ajones@ventanamicro.com \
--cc=anup@brainfault.org \
--cc=arnd@arndb.de \
--cc=atishp@atishpatra.org \
--cc=conor.dooley@microchip.com \
--cc=heiko@sntech.de \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=lkp@intel.com \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox