[PATCH v2 4/4] arm64: dts: qcom: sa8775p: add the BT high-speed UART for sa8775p-ride

[Bartosz Golaszewski <brgl@bgdev.pl>]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the serial port connected to the Bluetooth controller on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 33 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sa8775p.dtsi     | 17 ++++++++++++
 2 files changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
index 47cf26ea49e8..e7629cb0306c 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
@@ -14,6 +14,7 @@ / {
 	aliases {
 		serial0 = &uart10;
 		serial1 = &uart12;
+		serial2 = &uart17;
 		i2c18 = &i2c18;
 		spi16 = &spi16;
 	};
@@ -89,6 +90,29 @@ qup_uart12_tx: qup_uart12_tx-state {
 	qup_uart12_rx: qup_uart12_rx-state {
 		pins = "gpio55";
 		function = "qup1_se5";
+	};
+
+	qup_uart17_cts: qup-uart17-cts-state {
+		pins = "gpio91";
+		function = "qup2_se3";
+		bias-disable;
+	};
+
+	qup_uart17_rts: qup0_uart17_rts-state {
+		pins = "gpio92";
+		function = "qup2_se3";
+		bias-pull-down;
+	};
+
+	qup_uart17_tx: qup0_uart17_tx-state {
+		pins = "gpio93";
+		function = "qup2_se3";
+		bias-pull-up;
+	};
+
+	qup_uart17_rx: qup0_uart17_rx-state {
+		pins = "gpio94";
+		function = "qup2_se3";
 		bias-pull-down;
 	};
 };
@@ -109,6 +133,15 @@ &uart12 {
 	status = "okay";
 };
 
+&uart17 {
+	pinctrl-0 = <&qup_uart17_cts>,
+		    <&qup_uart17_rts>,
+		    <&qup_uart17_tx>,
+		    <&qup_uart17_rx>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
 &xo_board_clk {
 	clock-frequency = <38400000>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index 8b8931ea739d..9e057a34b14f 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -539,6 +539,23 @@ &config_noc SLAVE_QUP_2 0>,
 				status = "disabled";
 			};
 
+			uart17: serial@88c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x88c000 0x0 0x4000>;
+				interrupts-extended = <&intc GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>,
+						      <&tlmm 94 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0
+						 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0
+						 &config_noc SLAVE_QUP_2 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c18: i2c@890000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x890000 0x0 0x4000>;
-- 
2.37.2