[PATCH 04/28] bnx2x: Drop redundant pci_enable_pcie_error_reporting()

[Bjorn Helgaas <helgaas@kernel.org>]

From: Bjorn Helgaas <bhelgaas@google.com>

pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages.  Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.

Remove the redundant pci_enable_pcie_error_reporting() call from the
driver.  Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.

Note that this only controls ERR_* Messages from the device.  An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
---
 drivers/net/ethernet/broadcom/bnx2x/bnx2x.h   |  1 -
 .../net/ethernet/broadcom/bnx2x/bnx2x_main.c  | 19 -------------------
 2 files changed, 20 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index dd5945c4bfec..8bcde0a6e011 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1486,7 +1486,6 @@ struct bnx2x {
 #define IS_VF_FLAG			(1 << 22)
 #define BC_SUPPORTS_RMMOD_CMD		(1 << 23)
 #define HAS_PHYS_PORT_ID		(1 << 24)
-#define AER_ENABLED			(1 << 25)
 #define PTP_SUPPORTED			(1 << 26)
 #define TX_TIMESTAMPING_EN		(1 << 27)
 
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 5d1e4fe335aa..3bb5ea570c87 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -29,7 +29,6 @@
 #include <linux/slab.h>
 #include <linux/interrupt.h>
 #include <linux/pci.h>
-#include <linux/aer.h>
 #include <linux/init.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
@@ -13037,14 +13036,6 @@ static const struct net_device_ops bnx2x_netdev_ops = {
 	.ndo_features_check	= bnx2x_features_check,
 };
 
-static void bnx2x_disable_pcie_error_reporting(struct bnx2x *bp)
-{
-	if (bp->flags & AER_ENABLED) {
-		pci_disable_pcie_error_reporting(bp->pdev);
-		bp->flags &= ~AER_ENABLED;
-	}
-}
-
 static int bnx2x_init_dev(struct bnx2x *bp, struct pci_dev *pdev,
 			  struct net_device *dev, unsigned long board_type)
 {
@@ -13157,13 +13148,6 @@ static int bnx2x_init_dev(struct bnx2x *bp, struct pci_dev *pdev,
 	/* Set PCIe reset type to fundamental for EEH recovery */
 	pdev->needs_freset = 1;
 
-	/* AER (Advanced Error reporting) configuration */
-	rc = pci_enable_pcie_error_reporting(pdev);
-	if (!rc)
-		bp->flags |= AER_ENABLED;
-	else
-		BNX2X_DEV_INFO("Failed To configure PCIe AER [%d]\n", rc);
-
 	/*
 	 * Clean the following indirect addresses for all functions since it
 	 * is not used by the driver.
@@ -14020,8 +14004,6 @@ static int bnx2x_init_one(struct pci_dev *pdev,
 	bnx2x_free_mem_bp(bp);
 
 init_one_exit:
-	bnx2x_disable_pcie_error_reporting(bp);
-
 	if (bp->regview)
 		iounmap(bp->regview);
 
@@ -14102,7 +14084,6 @@ static void __bnx2x_remove(struct pci_dev *pdev,
 		pci_set_power_state(pdev, PCI_D3hot);
 	}
 
-	bnx2x_disable_pcie_error_reporting(bp);
 	if (remove_netdev) {
 		if (bp->regview)
 			iounmap(bp->regview);
-- 
2.25.1