From: Bartosz Golaszewski <brgl@bgdev.pl>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Subject: [PATCH v4 0/9] arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs
Date: Wed, 8 Mar 2023 11:40:00 +0100 [thread overview]
Message-ID: <20230308104009.260451-1-brgl@bgdev.pl> (raw)
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This enables the QUPv3 interfaces that are exposed on the sa8775p-ride
board: I2C, SPI and the Bluetooth and GNSS UART ports.
v3 -> v4:
- use interconnect constants instead of magic numbers where applicable
- pad addresses in reg to 8 digits
- group pins under state nodes for UART
v2 -> v3:
- fix the interrupt number for uart12
- replace underscores with hyphens in DT node names (although make dtbs_check
does not raise warnings about this)
- rearrange the commits so that they're more fine-grained with separate
patches for adding nodes to dtsi and enabling them for the board
v1 -> v2:
- uart17 is the Bluetooth port, not GNSS
- add uart12 for GNSS too in that case
Bartosz Golaszewski (9):
arm64: dts: qcom: sa8775p: add the QUPv3 #2 node
arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2
arm64: dts: qcom: sa8775p: add the i2c18 node
arm64: dts: qcom: sa8775p-ride: enable i2c18
arm64: dts: qcom: sa8775p: add the spi16 node
arm64: dts: qcom: sa8775p-ride: enable the SPI node
arm64: dts: qcom: sa8775p: add high-speed UART nodes
arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port
arm64: dts: qcom: sa8775p-ride: enable the BT UART port
arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 99 +++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sa8775p.dtsi | 87 ++++++++++++++++++++
2 files changed, 186 insertions(+)
--
2.37.2
next reply other threads:[~2023-03-08 10:40 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-08 10:40 Bartosz Golaszewski [this message]
2023-03-08 10:40 ` [PATCH v4 1/9] arm64: dts: qcom: sa8775p: add the QUPv3 #2 node Bartosz Golaszewski
2023-03-08 10:40 ` [PATCH v4 2/9] arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2 Bartosz Golaszewski
2023-03-08 16:41 ` Konrad Dybcio
2023-03-08 10:40 ` [PATCH v4 3/9] arm64: dts: qcom: sa8775p: add the i2c18 node Bartosz Golaszewski
2023-03-08 16:41 ` Konrad Dybcio
2023-03-08 10:40 ` [PATCH v4 4/9] arm64: dts: qcom: sa8775p-ride: enable i2c18 Bartosz Golaszewski
2023-03-08 10:40 ` [PATCH v4 5/9] arm64: dts: qcom: sa8775p: add the spi16 node Bartosz Golaszewski
2023-03-08 10:40 ` [PATCH v4 6/9] arm64: dts: qcom: sa8775p-ride: enable the SPI node Bartosz Golaszewski
2023-03-08 10:58 ` Konrad Dybcio
2023-03-08 12:36 ` Bartosz Golaszewski
2023-03-08 10:40 ` [PATCH v4 7/9] arm64: dts: qcom: sa8775p: add high-speed UART nodes Bartosz Golaszewski
2023-03-08 10:57 ` Konrad Dybcio
2023-03-08 16:02 ` Bartosz Golaszewski
2023-03-08 10:40 ` [PATCH v4 8/9] arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port Bartosz Golaszewski
2023-03-08 10:54 ` Konrad Dybcio
2023-03-08 10:40 ` [PATCH v4 9/9] arm64: dts: qcom: sa8775p-ride: enable the BT " Bartosz Golaszewski
2023-03-08 10:54 ` Konrad Dybcio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230308104009.260451-1-brgl@bgdev.pl \
--to=brgl@bgdev.pl \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=bartosz.golaszewski@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox