[patch V4 21/37] cpu/hotplug: Remove cpu_report_state() and related unused cruft

[Thomas Gleixner <tglx@linutronix.de>]

From: Thomas Gleixner <tglx@linutronix.de>

No more users.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
---
 include/linux/cpu.h |    2 -
 kernel/smpboot.c    |   90 ----------------------------------------------------
 2 files changed, 92 deletions(-)


--- a/include/linux/cpu.h
+++ b/include/linux/cpu.h
@@ -184,8 +184,6 @@ void arch_cpu_idle_enter(void);
 void arch_cpu_idle_exit(void);
 void __noreturn arch_cpu_idle_dead(void);
 
-int cpu_report_state(int cpu);
-int cpu_check_up_prepare(int cpu);
 void cpu_set_state_online(int cpu);
 void play_idle_precise(u64 duration_ns, u64 latency_ns);
 
--- a/kernel/smpboot.c
+++ b/kernel/smpboot.c
@@ -329,97 +329,7 @@ EXPORT_SYMBOL_GPL(smpboot_unregister_per
 #ifndef CONFIG_HOTPLUG_CORE_SYNC
 static DEFINE_PER_CPU(atomic_t, cpu_hotplug_state) = ATOMIC_INIT(CPU_POST_DEAD);
 
-/*
- * Called to poll specified CPU's state, for example, when waiting for
- * a CPU to come online.
- */
-int cpu_report_state(int cpu)
-{
-	return atomic_read(&per_cpu(cpu_hotplug_state, cpu));
-}
-
-/*
- * If CPU has died properly, set its state to CPU_UP_PREPARE and
- * return success.  Otherwise, return -EBUSY if the CPU died after
- * cpu_wait_death() timed out.  And yet otherwise again, return -EAGAIN
- * if cpu_wait_death() timed out and the CPU still hasn't gotten around
- * to dying.  In the latter two cases, the CPU might not be set up
- * properly, but it is up to the arch-specific code to decide.
- * Finally, -EIO indicates an unanticipated problem.
- *
- * Note that it is permissible to omit this call entirely, as is
- * done in architectures that do no CPU-hotplug error checking.
- */
-int cpu_check_up_prepare(int cpu)
-{
-	if (!IS_ENABLED(CONFIG_HOTPLUG_CPU)) {
-		atomic_set(&per_cpu(cpu_hotplug_state, cpu), CPU_UP_PREPARE);
-		return 0;
-	}
-
-	switch (atomic_read(&per_cpu(cpu_hotplug_state, cpu))) {
-
-	case CPU_POST_DEAD:
-
-		/* The CPU died properly, so just start it up again. */
-		atomic_set(&per_cpu(cpu_hotplug_state, cpu), CPU_UP_PREPARE);
-		return 0;
-
-	case CPU_DEAD_FROZEN:
-
-		/*
-		 * Timeout during CPU death, so let caller know.
-		 * The outgoing CPU completed its processing, but after
-		 * cpu_wait_death() timed out and reported the error. The
-		 * caller is free to proceed, in which case the state
-		 * will be reset properly by cpu_set_state_online().
-		 * Proceeding despite this -EBUSY return makes sense
-		 * for systems where the outgoing CPUs take themselves
-		 * offline, with no post-death manipulation required from
-		 * a surviving CPU.
-		 */
-		return -EBUSY;
-
-	case CPU_BROKEN:
-
-		/*
-		 * The most likely reason we got here is that there was
-		 * a timeout during CPU death, and the outgoing CPU never
-		 * did complete its processing.  This could happen on
-		 * a virtualized system if the outgoing VCPU gets preempted
-		 * for more than five seconds, and the user attempts to
-		 * immediately online that same CPU.  Trying again later
-		 * might return -EBUSY above, hence -EAGAIN.
-		 */
-		return -EAGAIN;
-
-	case CPU_UP_PREPARE:
-		/*
-		 * Timeout while waiting for the CPU to show up. Allow to try
-		 * again later.
-		 */
-		return 0;
-
-	default:
-
-		/* Should not happen.  Famous last words. */
-		return -EIO;
-	}
-}
-
-/*
- * Mark the specified CPU online.
- *
- * Note that it is permissible to omit this call entirely, as is
- * done in architectures that do no CPU-hotplug error checking.
- */
-void cpu_set_state_online(int cpu)
-{
-	(void)atomic_xchg(&per_cpu(cpu_hotplug_state, cpu), CPU_ONLINE);
-}
-
 #ifdef CONFIG_HOTPLUG_CPU
-
 /*
  * Wait for the specified CPU to exit the idle loop and die.
  */