From: Vinod Koul <vkoul@kernel.org>
To: Bjorn Andersson <andersson@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Vinod Koul <vkoul@kernel.org>
Subject: [PATCH v3 10/15] arm64: dts: qcom: sc8180x: Add PCIe instances
Date: Tue, 30 May 2023 21:54:49 +0530 [thread overview]
Message-ID: <20230530162454.51708-11-vkoul@kernel.org> (raw)
In-Reply-To: <20230530162454.51708-1-vkoul@kernel.org>
This patch adds PCIe instances found on this SoC
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sc8180x.dtsi | 429 ++++++++++++++++++++++++++
1 file changed, 429 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
index b50673b7c147..2639f5fb6e39 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
@@ -1681,6 +1681,435 @@ mmss_noc: interconnect@1740000 {
qcom,bcm-voters = <&apps_bcm_voter>;
};
+ pcie0: pci@1c00000 {
+ compatible = "qcom,pcie-sc8180x";
+ reg = <0 0x01c00000 0 0x3000>,
+ <0 0x60000000 0 0xf1d>,
+ <0 0x60000f20 0 0xa8>,
+ <0 0x60001000 0 0x1000>,
+ <0 0x60100000 0 0x100000>;
+ reg-names = "parf",
+ "dbi",
+ "elbi",
+ "atu",
+ "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x60200000 0x0 0x60200000 0x0 0x100000>,
+ <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
+
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_0_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1d80 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1d80 0x1>,
+ <0x100 &apps_smmu 0x1d81 0x1>;
+
+ resets = <&gcc GCC_PCIE_0_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_0_GDSC>;
+
+ interconnects = <&aggre2_noc MASTER_PCIE 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ phys = <&pcie0_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie0_phy: phy-wrapper@1c06000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c06000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_CLKREF_CLK>,
+ <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie0_lane: phy@1c06200 {
+ reg = <0 0x1c06200 0 0x170>, /* tx0 */
+ <0 0x1c06400 0 0x200>, /* rx0 */
+ <0 0x1c06a00 0 0x1f0>, /* pcs */
+ <0 0x1c06600 0 0x170>, /* tx1 */
+ <0 0x1c06800 0 0x200>, /* rx1 */
+ <0 0x1c06e00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie_0_pipe_clk";
+ #phy-cells = <0>;
+ };
+ };
+
+ pcie3: pci@1c08000 {
+ compatible = "qcom,pcie-sc8180x";
+ reg = <0 0x01c08000 0 0x3000>,
+ <0 0x40000000 0 0xf1d>,
+ <0 0x40000f20 0 0xa8>,
+ <0 0x40001000 0 0x1000>,
+ <0 0x40100000 0 0x100000>;
+ reg-names = "parf",
+ "dbi",
+ "elbi",
+ "atu",
+ "config";
+ device_type = "pci";
+ linux,pci-domain = <3>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+ <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_3_PIPE_CLK>,
+ <&gcc GCC_PCIE_3_AUX_CLK>,
+ <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_3_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1e00 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1e00 0x1>,
+ <0x100 &apps_smmu 0x1e01 0x1>;
+
+ resets = <&gcc GCC_PCIE_3_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_3_GDSC>;
+
+ interconnects = <&aggre2_noc MASTER_PCIE_3 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ phys = <&pcie3_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie3_phy: phy-wrapper@1c0c000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c0c000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_3_CLKREF_CLK>,
+ <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_3_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE3_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie3_lane: phy@1c0c200 {
+ reg = <0 0x1c0c200 0 0x170>, /* tx0 */
+ <0 0x1c0c400 0 0x200>, /* rx0 */
+ <0 0x1c0ca00 0 0x1f0>, /* pcs */
+ <0 0x1c0c600 0 0x170>, /* tx1 */
+ <0 0x1c0c800 0 0x200>, /* rx1 */
+ <0 0x1c0ce00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_3_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie_3_pipe_clk";
+ #phy-cells = <0>;
+ };
+ };
+
+ pcie1: pci@1c10000 {
+ compatible = "qcom,pcie-sc8180x";
+ reg = <0 0x01c10000 0 0x3000>,
+ <0 0x68000000 0 0xf1d>,
+ <0 0x68000f20 0 0xa8>,
+ <0 0x68001000 0 0x1000>,
+ <0 0x68100000 0 0x100000>;
+ reg-names = "parf",
+ "dbi",
+ "elbi",
+ "atu",
+ "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x68200000 0x0 0x68200000 0x0 0x100000>,
+ <0x02000000 0x0 0x68300000 0x0 0x68300000 0x0 0x3d00000>;
+
+ interrupts = <GIC_SPI 755 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 747 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 746 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 745 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 744 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+ <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_1_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1c80 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
+ <0x100 &apps_smmu 0x1c81 0x1>;
+
+ resets = <&gcc GCC_PCIE_1_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_1_GDSC>;
+
+ interconnects = <&aggre2_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ phys = <&pcie1_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie1_phy: phy-wrapper@1c16000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c16000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_CLKREF_CLK>,
+ <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie1_lane: phy@1c0e200 {
+ reg = <0 0x1c16200 0 0x170>, /* tx0 */
+ <0 0x1c16400 0 0x200>, /* rx0 */
+ <0 0x1c16a00 0 0x1f0>, /* pcs */
+ <0 0x1c16600 0 0x170>, /* tx1 */
+ <0 0x1c16800 0 0x200>, /* rx1 */
+ <0 0x1c16e00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+ clock-names = "pipe0";
+ #clock-cells = <0>;
+ clock-output-names = "pcie_1_pipe_clk";
+
+ #phy-cells = <0>;
+ };
+ };
+
+ pcie2: pci@1c18000 {
+ compatible = "qcom,pcie-sc8180x";
+ reg = <0 0x01c18000 0 0x3000>,
+ <0 0x70000000 0 0xf1d>,
+ <0 0x70000f20 0 0xa8>,
+ <0 0x70001000 0 0x1000>,
+ <0 0x70100000 0 0x100000>;
+ reg-names = "parf",
+ "dbi",
+ "elbi",
+ "atu",
+ "config";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <4>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x70200000 0x0 0x70200000 0x0 0x100000>,
+ <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;
+
+ interrupts = <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 663 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 662 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 661 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 660 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
+ <&gcc GCC_PCIE_2_AUX_CLK>,
+ <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_2_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_2_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1d00 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1d00 0x1>,
+ <0x100 &apps_smmu 0x1d01 0x1>;
+
+ resets = <&gcc GCC_PCIE_2_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_2_GDSC>;
+
+ interconnects = <&aggre2_noc MASTER_PCIE_2 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ phys = <&pcie2_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie2_phy: phy-wrapper@1c1c000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c1c000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_2_CLKREF_CLK>,
+ <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_2_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie2_lane: phy@1c0e200 {
+ reg = <0 0x1c1c200 0 0x170>, /* tx0 */
+ <0 0x1c1c400 0 0x200>, /* rx0 */
+ <0 0x1c1ca00 0 0x1f0>, /* pcs */
+ <0 0x1c1c600 0 0x170>, /* tx1 */
+ <0 0x1c1c800 0 0x200>, /* rx1 */
+ <0 0x1c1ce00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie_2_pipe_clk";
+
+ #phy-cells = <0>;
+ };
+ };
+
ufs_mem_hc: ufshc@1d84000 {
compatible = "qcom,sc8180x-ufshc", "qcom,ufshc",
"jedec,ufs-2.0";
--
2.40.1
next prev parent reply other threads:[~2023-05-30 16:26 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-30 16:24 [PATCH v3 00/15] Introduce the SC8180x devices Vinod Koul
2023-05-30 16:24 ` [PATCH v3 01/15] dt-bindings: PCI: qcom: Fix sc8180x clocks and interrupts Vinod Koul
2023-05-31 8:19 ` Krzysztof Kozlowski
2023-06-01 7:21 ` Vinod Koul
2023-06-01 7:25 ` Krzysztof Kozlowski
2023-06-01 7:26 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 02/15] dt-bindings: usb: qcom,dwc3: Add SC8180x binding Vinod Koul
2023-05-31 8:19 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 03/15] dt-bindings: interconnect: split SC8180x to own schema Vinod Koul
2023-05-31 8:22 ` Krzysztof Kozlowski
2023-06-01 7:23 ` Vinod Koul
2023-06-01 7:26 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 04/15] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
2023-05-31 8:24 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 05/15] dt-bindings: qcom,pdc: Add SC8180x compatible Vinod Koul
2023-05-31 8:24 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 06/15] arm64: dts: qcom: Introduce the SC8180x platform Vinod Koul
2023-05-30 16:24 ` [PATCH v3 07/15] arm64: dts: qcom: sc8180x: Add interconnects and lmh Vinod Koul
2023-05-31 8:26 ` Krzysztof Kozlowski
2023-06-01 7:17 ` Vinod Koul
2023-06-01 13:27 ` Bjorn Andersson
2023-06-01 15:27 ` Krzysztof Kozlowski
2023-06-10 16:24 ` Bjorn Andersson
2023-05-30 16:24 ` [PATCH v3 08/15] arm64: dts: qcom: sc8180x: Add thermal zones Vinod Koul
2023-05-30 16:24 ` [PATCH v3 09/15] arm64: dts: qcom: sc8180x: Add QUPs Vinod Koul
2023-05-30 16:24 ` Vinod Koul [this message]
2023-05-30 16:24 ` [PATCH v3 11/15] arm64: dts: qcom: sc8180x: Add remoteprocs, wifi and usb nodes Vinod Koul
2023-05-30 16:24 ` [PATCH v3 12/15] arm64: dts: qcom: sc8180x: Add display and gpu nodes Vinod Koul
2023-05-30 16:24 ` [PATCH v3 13/15] arm64: dts: qcom: sc8180x: Add pmics Vinod Koul
2023-06-07 19:31 ` Rob Herring
2023-05-30 16:24 ` [PATCH v3 14/15] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
2023-05-30 16:24 ` [PATCH v3 15/15] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
2023-05-30 17:22 ` (subset) [PATCH v3 00/15] Introduce the SC8180x devices Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230530162454.51708-11-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox