From: Vinod Koul <vkoul@kernel.org>
To: Bjorn Andersson <andersson@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Vinod Koul <vkoul@kernel.org>
Subject: [PATCH v3 08/15] arm64: dts: qcom: sc8180x: Add thermal zones
Date: Tue, 30 May 2023 21:54:47 +0530 [thread overview]
Message-ID: <20230530162454.51708-9-vkoul@kernel.org> (raw)
In-Reply-To: <20230530162454.51708-1-vkoul@kernel.org>
This patch adds tsens nodes and thermal zones for sc8180x SoC
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sc8180x.dtsi | 415 ++++++++++++++++++++++++++
1 file changed, 415 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
index 08f5ad65efd5..da7c08e70540 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
interrupt-parent = <&intc>;
@@ -961,6 +962,28 @@ pdc: interrupt-controller@b220000 {
interrupt-controller;
};
+ tsens0: thermal-sensor@c263000 {
+ compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c263000 0 0x1ff>, /* TM */
+ <0 0x0c222000 0 0x1ff>; /* SROT */
+ #qcom,sensors = <16>;
+ interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
+ tsens1: thermal-sensor@c265000 {
+ compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c265000 0 0x1ff>, /* TM */
+ <0 0x0c223000 0 0x1ff>; /* SROT */
+ #qcom,sensors = <9>;
+ interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
aoss_qmp: power-controller@c300000 {
compatible = "qcom,sc8180x-aoss-qmp", "qcom,aoss-qmp";
reg = <0x0 0x0c300000 0x0 0x100000>;
@@ -1304,6 +1327,398 @@ cpufreq_hw: cpufreq@18323000 {
#clock-cells = <1>;
};
+ thermal-zones {
+ cpu0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 1>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 2>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 3>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu3-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 4>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu4-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 7>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu5-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 8>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu6-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 9>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu7-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 10>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu4-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 11>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu5-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 12>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu6-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 13>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu7-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 14>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ aoss0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ cluster0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 5>;
+
+ trips {
+ cluster-crit {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cluster1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 6>;
+
+ trips {
+ cluster-crit {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpu-thermal-top {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 15>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ aoss1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ wlan-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 1>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ video-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 2>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ mem-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 3>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ q6-hvx-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 4>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ camera-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 5>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ compute-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 6>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ mdm-dsp-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 7>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ npu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 8>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ gpu-thermal-bottom {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 11>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
--
2.40.1
next prev parent reply other threads:[~2023-05-30 16:26 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-30 16:24 [PATCH v3 00/15] Introduce the SC8180x devices Vinod Koul
2023-05-30 16:24 ` [PATCH v3 01/15] dt-bindings: PCI: qcom: Fix sc8180x clocks and interrupts Vinod Koul
2023-05-31 8:19 ` Krzysztof Kozlowski
2023-06-01 7:21 ` Vinod Koul
2023-06-01 7:25 ` Krzysztof Kozlowski
2023-06-01 7:26 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 02/15] dt-bindings: usb: qcom,dwc3: Add SC8180x binding Vinod Koul
2023-05-31 8:19 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 03/15] dt-bindings: interconnect: split SC8180x to own schema Vinod Koul
2023-05-31 8:22 ` Krzysztof Kozlowski
2023-06-01 7:23 ` Vinod Koul
2023-06-01 7:26 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 04/15] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
2023-05-31 8:24 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 05/15] dt-bindings: qcom,pdc: Add SC8180x compatible Vinod Koul
2023-05-31 8:24 ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 06/15] arm64: dts: qcom: Introduce the SC8180x platform Vinod Koul
2023-05-30 16:24 ` [PATCH v3 07/15] arm64: dts: qcom: sc8180x: Add interconnects and lmh Vinod Koul
2023-05-31 8:26 ` Krzysztof Kozlowski
2023-06-01 7:17 ` Vinod Koul
2023-06-01 13:27 ` Bjorn Andersson
2023-06-01 15:27 ` Krzysztof Kozlowski
2023-06-10 16:24 ` Bjorn Andersson
2023-05-30 16:24 ` Vinod Koul [this message]
2023-05-30 16:24 ` [PATCH v3 09/15] arm64: dts: qcom: sc8180x: Add QUPs Vinod Koul
2023-05-30 16:24 ` [PATCH v3 10/15] arm64: dts: qcom: sc8180x: Add PCIe instances Vinod Koul
2023-05-30 16:24 ` [PATCH v3 11/15] arm64: dts: qcom: sc8180x: Add remoteprocs, wifi and usb nodes Vinod Koul
2023-05-30 16:24 ` [PATCH v3 12/15] arm64: dts: qcom: sc8180x: Add display and gpu nodes Vinod Koul
2023-05-30 16:24 ` [PATCH v3 13/15] arm64: dts: qcom: sc8180x: Add pmics Vinod Koul
2023-06-07 19:31 ` Rob Herring
2023-05-30 16:24 ` [PATCH v3 14/15] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
2023-05-30 16:24 ` [PATCH v3 15/15] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
2023-05-30 17:22 ` (subset) [PATCH v3 00/15] Introduce the SC8180x devices Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230530162454.51708-9-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox