[PATCH AUTOSEL 6.1 01/12] arm64: dts: rockchip: fix USB regulator on ROCK64

[Sasha Levin <sashal@kernel.org>]

From: Lorenz Brun <lorenz@brun.one>

[ Upstream commit 03633c4ef1fb5ee119296dfe0c411656a9b5e04f ]

Currently the ROCK64 device tree specifies two regulators, vcc_host_5v
and vcc_host1_5v for USB VBUS on the device. Both of those are however
specified with RK_PA2 as the GPIO enabling them, causing the following
error when booting:

  rockchip-pinctrl pinctrl: pin gpio0-2 already requested by vcc-host-5v-regulator; cannot claim for vcc-host1-5v-regulator
  rockchip-pinctrl pinctrl: pin-2 (vcc-host1-5v-regulator) status -22
  rockchip-pinctrl pinctrl: could not request pin 2 (gpio0-2) from group usb20-host-drv  on device rockchip-pinctrl
  reg-fixed-voltage vcc-host1-5v-regulator: Error applying setting, reverse things back

Looking at the schematic, there are in fact three USB regulators,
vcc_host_5v, vcc_host1_5v and vcc_otg_v5. But the enable signal for all
three is driven by Q2604 which is in turn driven by GPIO_A2/PA2.

Since these three regulators are not controllable separately, I removed
the second one which was causing the error and added labels for all
rails to the single regulator.

Signed-off-by: Lorenz Brun <lorenz@brun.one>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20230421213841.3079632-1-lorenz@brun.one
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 14 ++------------
 1 file changed, 2 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index f69a38f42d2d5..0a27fa5271f57 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -37,7 +37,8 @@ vcc_sd: sdmmc-regulator {
 		vin-supply = <&vcc_io>;
 	};
 
-	vcc_host_5v: vcc-host-5v-regulator {
+	/* Common enable line for all of the rails mentioned in the labels */
+	vcc_host_5v: vcc_host1_5v: vcc_otg_5v: vcc-host-5v-regulator {
 		compatible = "regulator-fixed";
 		gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
@@ -48,17 +49,6 @@ vcc_host_5v: vcc-host-5v-regulator {
 		vin-supply = <&vcc_sys>;
 	};
 
-	vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
-		compatible = "regulator-fixed";
-		gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb20_host_drv>;
-		regulator-name = "vcc_host1_5v";
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&vcc_sys>;
-	};
-
 	vcc_sys: vcc-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_sys";
-- 
2.39.2