From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
To: Ira Weiny <ira.weiny@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>,
Navneet Singh <navneet.singh@intel.com>,
Fan Ni <fan.ni@samsung.com>, Davidlohr Bueso <dave@stgolabs.net>,
Dave Jiang <dave.jiang@intel.com>,
Alison Schofield <alison.schofield@intel.com>,
Vishal Verma <vishal.l.verma@intel.com>,
<linux-cxl@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH RFC v2 09/18] cxl/mem: Read extents on memory device discovery
Date: Tue, 29 Aug 2023 16:26:00 +0100 [thread overview]
Message-ID: <20230829162600.00004ac2@Huawei.com> (raw)
In-Reply-To: <20230604-dcd-type2-upstream-v2-9-f740c47e7916@intel.com>
On Mon, 28 Aug 2023 22:21:00 -0700
Ira Weiny <ira.weiny@intel.com> wrote:
> When a Dynamic Capacity Device (DCD) is realized some extents may
> already be available within the DC Regions. This can happen if the host
> has accepted extents and been rebooted or any other time the host driver
> software has become out of sync with the device hardware.
>
> Read the available extents during probe and store them for later
> use.
>
> Signed-off-by: Navneet Singh <navneet.singh@intel.com>
> Co-developed-by: Navneet Singh <navneet.singh@intel.com>
> Signed-off-by: Ira Weiny <ira.weiny@intel.com>
>
A few minor comments inline.
Thanks,
Jonathan
> ---
> Change for v2:
> [iweiny: new patch]
> ---
> drivers/cxl/core/mbox.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++++
> drivers/cxl/cxlmem.h | 36 +++++++++
> drivers/cxl/pci.c | 4 +
> 3 files changed, 235 insertions(+)
>
> diff --git a/drivers/cxl/core/mbox.c b/drivers/cxl/core/mbox.c
> index d769814f80e2..9b08c40ef484 100644
> --- a/drivers/cxl/core/mbox.c
> +++ b/drivers/cxl/core/mbox.c
> @@ -824,6 +824,37 @@ int cxl_enumerate_cmds(struct cxl_memdev_state *mds)
...
> +static int cxl_dev_get_dc_extent_cnt(struct cxl_memdev_state *mds,
> + unsigned int *extent_gen_num)
> +{
> + struct cxl_mbox_get_dc_extent get_dc_extent;
> + struct cxl_mbox_dc_extents dc_extents;
> + struct device *dev = mds->cxlds.dev;
> + struct cxl_mbox_cmd mbox_cmd;
> + unsigned int count;
> + int rc;
> +
> + /* Check GET_DC_EXTENT_LIST is supported by device */
> + if (!test_bit(CXL_DCD_ENABLED_GET_EXTENT_LIST, mds->dcd_cmds)) {
> + dev_dbg(dev, "unsupported cmd : get dyn cap extent list\n");
> + return 0;
> + }
> +
> + get_dc_extent = (struct cxl_mbox_get_dc_extent) {
> + .extent_cnt = cpu_to_le32(0),
> + .start_extent_index = cpu_to_le32(0),
> + };
> +
> + mbox_cmd = (struct cxl_mbox_cmd) {
> + .opcode = CXL_MBOX_OP_GET_DC_EXTENT_LIST,
> + .payload_in = &get_dc_extent,
> + .size_in = sizeof(get_dc_extent),
> + .size_out = mds->payload_size,
If all you are after is the count, then size_out can be a lot smaller than that
I think as we know it can't return any extents.
> + .payload_out = &dc_extents,
> + .min_out = 1,
> + };
> +
> + rc = cxl_internal_send_cmd(mds, &mbox_cmd);
> + if (rc < 0)
> + return rc;
> +
> + count = le32_to_cpu(dc_extents.total_extent_cnt);
> + *extent_gen_num = le32_to_cpu(dc_extents.extent_list_num);
> +
> + return count;
> +}
> +
> +static int cxl_dev_get_dc_extents(struct cxl_memdev_state *mds,
> + unsigned int start_gen_num,
> + unsigned int exp_cnt)
> +{
> + struct cxl_mbox_dc_extents *dc_extents;
> + unsigned int start_index, total_read;
> + struct device *dev = mds->cxlds.dev;
> + struct cxl_mbox_cmd mbox_cmd;
> + int retry = 3;
Why 3?
> + int rc;
> +
> + /* Check GET_DC_EXTENT_LIST is supported by device */
> + if (!test_bit(CXL_DCD_ENABLED_GET_EXTENT_LIST, mds->dcd_cmds)) {
> + dev_dbg(dev, "unsupported cmd : get dyn cap extent list\n");
> + return 0;
> + }
> +
> + dc_extents = kvmalloc(mds->payload_size, GFP_KERNEL);
Maybe __free magic would simplify this enough to be useful.
> + if (!dc_extents)
> + return -ENOMEM;
> +
> +reset:
> + total_read = 0;
> + start_index = 0;
> + do {
> + unsigned int nr_ext, total_extent_cnt, gen_num;
> + struct cxl_mbox_get_dc_extent get_dc_extent;
> +
> + get_dc_extent = (struct cxl_mbox_get_dc_extent) {
> + .extent_cnt = exp_cnt - start_index,
> + .start_extent_index = start_index,
> + };
> +
> + mbox_cmd = (struct cxl_mbox_cmd) {
> + .opcode = CXL_MBOX_OP_GET_DC_EXTENT_LIST,
> + .payload_in = &get_dc_extent,
> + .size_in = sizeof(get_dc_extent),
> + .size_out = mds->payload_size,
> + .payload_out = dc_extents,
> + .min_out = 1,
> + };
> +
> + rc = cxl_internal_send_cmd(mds, &mbox_cmd);
> + if (rc < 0)
> + goto out;
> +
> + nr_ext = le32_to_cpu(dc_extents->ret_extent_cnt);
> + total_read += nr_ext;
> + total_extent_cnt = le32_to_cpu(dc_extents->total_extent_cnt);
> + gen_num = le32_to_cpu(dc_extents->extent_list_num);
> +
> + dev_dbg(dev, "Get extent list count:%d generation Num:%d\n",
> + total_extent_cnt, gen_num);
> +
> + if (gen_num != start_gen_num || exp_cnt != total_extent_cnt) {
> + dev_err(dev, "Extent list changed while reading; %u != %u : %u != %u\n",
> + gen_num, start_gen_num, exp_cnt, total_extent_cnt);
> + if (retry--)
> + goto reset;
> + return -EIO;
> + }
> +
> + for (int i = 0; i < nr_ext ; i++) {
> + dev_dbg(dev, "Storing extent %d/%d\n",
> + start_index + i, exp_cnt);
> + rc = cxl_store_dc_extent(mds, &dc_extents->extent[i]);
> + if (rc)
> + goto out;
> + }
> +
> + start_index += nr_ext;
> + } while (exp_cnt > total_read);
> +
> +out:
> + kvfree(dc_extents);
> + return rc;
> +}
next prev parent reply other threads:[~2023-08-29 15:27 UTC|newest]
Thread overview: 97+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-29 5:20 [PATCH RFC v2 00/18] DCD: Add support for Dynamic Capacity Devices (DCD) Ira Weiny
2023-08-29 5:20 ` [PATCH RFC v2 01/18] cxl/hdm: Debug, use decoder name function Ira Weiny
2023-08-29 14:03 ` Jonathan Cameron
2023-08-29 21:48 ` Fan Ni
2023-09-03 2:55 ` Ira Weiny
2023-08-30 20:32 ` Dave Jiang
2023-08-29 5:20 ` [PATCH RFC v2 02/18] cxl/mbox: Flag support for Dynamic Capacity Devices (DCD) Ira Weiny
2023-08-29 14:07 ` Jonathan Cameron
2023-09-03 3:38 ` Ira Weiny
2023-08-29 21:49 ` Fan Ni
2023-08-30 20:33 ` Dave Jiang
2023-10-24 16:16 ` Jonathan Cameron
2023-08-29 5:20 ` [PATCH RFC v2 03/18] cxl/mem: Read Dynamic capacity configuration from the device ira.weiny
2023-08-29 14:37 ` Jonathan Cameron
2023-09-03 23:36 ` Ira Weiny
2023-08-30 21:01 ` Dave Jiang
2023-09-05 0:14 ` Ira Weiny
2023-09-08 20:23 ` Ira Weiny
2023-08-30 21:44 ` Fan Ni
2023-09-08 22:52 ` Ira Weiny
2023-09-12 21:32 ` Fan Ni
2023-09-07 15:46 ` Alison Schofield
2023-09-12 1:18 ` Ira Weiny
2023-09-08 12:46 ` Jørgen Hansen
2023-09-11 20:26 ` Ira Weiny
2023-08-29 5:20 ` [PATCH RFC v2 04/18] cxl/region: Add Dynamic Capacity decoder and region modes Ira Weiny
2023-08-29 14:39 ` Jonathan Cameron
2023-08-30 21:13 ` Dave Jiang
2023-08-31 17:00 ` Fan Ni
2023-08-29 5:20 ` [PATCH RFC v2 05/18] cxl/port: Add Dynamic Capacity mode support to endpoint decoders Ira Weiny
2023-08-29 14:49 ` Jonathan Cameron
2023-09-05 0:05 ` Ira Weiny
2023-08-31 17:25 ` Fan Ni
2023-09-08 23:26 ` Ira Weiny
2023-08-29 5:20 ` [PATCH RFC v2 06/18] cxl/port: Add Dynamic Capacity size " Ira Weiny
2023-08-29 15:09 ` Jonathan Cameron
2023-09-05 4:32 ` Ira Weiny
2023-08-29 5:20 ` [PATCH RFC v2 07/18] cxl/mem: Expose device dynamic capacity configuration ira.weiny
2023-08-29 15:14 ` Jonathan Cameron
2023-09-05 17:55 ` Fan Ni
2023-09-05 20:45 ` Ira Weiny
2023-08-30 22:46 ` Dave Jiang
2023-09-08 23:22 ` Ira Weiny
2023-08-29 5:20 ` [PATCH RFC v2 08/18] cxl/region: Add Dynamic Capacity CXL region support Ira Weiny
2023-08-29 15:19 ` Jonathan Cameron
2023-08-30 23:27 ` Dave Jiang
2023-09-06 4:36 ` Ira Weiny
2023-09-05 21:09 ` Fan Ni
2023-08-29 5:21 ` [PATCH RFC v2 09/18] cxl/mem: Read extents on memory device discovery Ira Weiny
2023-08-29 15:26 ` Jonathan Cameron [this message]
2023-08-30 0:16 ` Ira Weiny
2023-09-05 21:41 ` Ira Weiny
2023-08-29 5:21 ` [PATCH RFC v2 10/18] cxl/mem: Handle DCD add and release capacity events Ira Weiny
2023-08-29 15:59 ` Jonathan Cameron
2023-09-05 23:49 ` Ira Weiny
2023-08-31 17:28 ` Dave Jiang
2023-09-08 15:35 ` Ira Weiny
2023-08-29 5:21 ` [PATCH RFC v2 11/18] cxl/region: Expose DC extents on region driver load Ira Weiny
2023-08-29 16:20 ` Jonathan Cameron
2023-09-06 3:36 ` Ira Weiny
2023-08-31 18:38 ` Dave Jiang
2023-09-08 23:57 ` Ira Weiny
2023-08-29 5:21 ` [PATCH RFC v2 12/18] cxl/region: Notify regions of DC changes Ira Weiny
2023-08-29 16:40 ` Jonathan Cameron
2023-09-06 4:00 ` Ira Weiny
2023-09-18 13:56 ` Jørgen Hansen
2023-09-18 17:45 ` Ira Weiny
2023-08-29 5:21 ` [PATCH RFC v2 13/18] dax/bus: Factor out dev dax resize logic Ira Weiny
2023-08-30 11:27 ` Jonathan Cameron
2023-09-06 4:12 ` Ira Weiny
2023-08-31 21:48 ` Dave Jiang
2023-08-29 5:21 ` [PATCH RFC v2 14/18] dax/region: Support DAX device creation on dynamic DAX regions Ira Weiny
2023-08-30 11:50 ` Jonathan Cameron
2023-09-06 4:35 ` Ira Weiny
2023-09-12 16:49 ` Jonathan Cameron
2023-09-12 22:08 ` Ira Weiny
2023-09-12 22:35 ` Dan Williams
2023-09-13 17:30 ` Ira Weiny
2023-09-13 17:59 ` Dan Williams
2023-09-13 19:26 ` Ira Weiny
2023-09-14 10:32 ` Jonathan Cameron
2023-08-29 5:21 ` [PATCH RFC v2 15/18] cxl/mem: Trace Dynamic capacity Event Record ira.weiny
2023-08-29 16:46 ` Jonathan Cameron
2023-09-06 4:07 ` Ira Weiny
2023-08-29 5:21 ` [PATCH RFC v2 16/18] tools/testing/cxl: Make event logs dynamic Ira Weiny
2023-08-30 12:11 ` Jonathan Cameron
2023-09-06 21:15 ` Ira Weiny
2023-08-29 5:21 ` [PATCH RFC v2 17/18] tools/testing/cxl: Add DC Regions to mock mem data Ira Weiny
2023-08-30 12:20 ` Jonathan Cameron
2023-09-06 21:18 ` Ira Weiny
2023-08-31 23:19 ` Dave Jiang
2023-08-29 5:21 ` [PATCH RFC v2 18/18] tools/testing/cxl: Add Dynamic Capacity events Ira Weiny
2023-08-30 12:23 ` Jonathan Cameron
2023-09-06 21:39 ` Ira Weiny
2023-08-31 23:20 ` Dave Jiang
2023-09-07 21:01 ` [PATCH RFC v2 00/18] DCD: Add support for Dynamic Capacity Devices (DCD) Fan Ni
2023-09-12 1:44 ` Ira Weiny
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230829162600.00004ac2@Huawei.com \
--to=jonathan.cameron@huawei.com \
--cc=alison.schofield@intel.com \
--cc=dan.j.williams@intel.com \
--cc=dave.jiang@intel.com \
--cc=dave@stgolabs.net \
--cc=fan.ni@samsung.com \
--cc=ira.weiny@intel.com \
--cc=linux-cxl@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=navneet.singh@intel.com \
--cc=vishal.l.verma@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox