public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Markus Schneider-Pargmann <msp@baylibre.com>
To: Marc Kleine-Budde <mkl@pengutronix.de>,
	Chandrasekar Ramakrishnan <rcsekar@samsung.com>,
	Wolfgang Grandegger <wg@grandegger.com>
Cc: Vincent MAILHOL <mailhol.vincent@wanadoo.fr>,
	Simon Horman <simon.horman@corigine.com>,
	"David S . Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	linux-can@vger.kernel.org, netdev@vger.kernel.org,
	linux-kernel@vger.kernel.org, Julien Panis <jpanis@baylibre.com>,
	Judith Mendez <jm@ti.com>,
	Markus Schneider-Pargmann <msp@baylibre.com>
Subject: [PATCH v6 04/14] can: m_can: Implement receive coalescing
Date: Fri, 29 Sep 2023 16:12:54 +0200	[thread overview]
Message-ID: <20230929141304.3934380-5-msp@baylibre.com> (raw)
In-Reply-To: <20230929141304.3934380-1-msp@baylibre.com>

m_can offers the possibility to set an interrupt on reaching a watermark
level in the receive FIFO. This can be used to implement coalescing.
Unfortunately there is no hardware timeout available to trigger an
interrupt if only a few messages were received within a given time. To
solve this I am using a hrtimer to wake up the irq thread after x
microseconds.

The timer is always started if receive coalescing is enabled and new
received frames were available during an interrupt. The timer is stopped
if during a interrupt handling no new data was available.

If the timer is started the new item interrupt is disabled and the
watermark interrupt takes over. If the timer is not started again, the
new item interrupt is enabled again, notifying the handler about every
new item received.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 76 ++++++++++++++++++++++++++++++++---
 drivers/net/can/m_can/m_can.h |  5 +++
 2 files changed, 75 insertions(+), 6 deletions(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index a01c9261331d..4492fe0da29c 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -422,6 +422,25 @@ static void m_can_config_endisable(struct m_can_classdev *cdev, bool enable)
 	}
 }
 
+static void m_can_interrupt_enable(struct m_can_classdev *cdev, u32 interrupts)
+{
+	if (cdev->active_interrupts == interrupts)
+		return;
+	cdev->ops->write_reg(cdev, M_CAN_IE, interrupts);
+	cdev->active_interrupts = interrupts;
+}
+
+static void m_can_coalescing_disable(struct m_can_classdev *cdev)
+{
+	u32 new_interrupts = cdev->active_interrupts | IR_RF0N;
+
+	if (!cdev->net->irq)
+		return;
+
+	hrtimer_cancel(&cdev->hrtimer);
+	m_can_interrupt_enable(cdev, new_interrupts);
+}
+
 static inline void m_can_enable_all_interrupts(struct m_can_classdev *cdev)
 {
 	if (!cdev->net->irq) {
@@ -437,6 +456,7 @@ static inline void m_can_enable_all_interrupts(struct m_can_classdev *cdev)
 
 static inline void m_can_disable_all_interrupts(struct m_can_classdev *cdev)
 {
+	m_can_coalescing_disable(cdev);
 	m_can_write(cdev, M_CAN_ILE, 0x0);
 
 	if (!cdev->net->irq) {
@@ -1091,15 +1111,42 @@ static int m_can_echo_tx_event(struct net_device *dev)
 	return err;
 }
 
+static void m_can_coalescing_update(struct m_can_classdev *cdev, u32 ir)
+{
+	u32 new_interrupts = cdev->active_interrupts;
+	bool enable_timer = false;
+
+	if (!cdev->net->irq)
+		return;
+
+	if (cdev->rx_coalesce_usecs_irq > 0 && (ir & (IR_RF0N | IR_RF0W))) {
+		enable_timer = true;
+		new_interrupts &= ~IR_RF0N;
+	} else if (!hrtimer_active(&cdev->hrtimer)) {
+		new_interrupts |= IR_RF0N;
+	}
+
+	m_can_interrupt_enable(cdev, new_interrupts);
+	if (enable_timer) {
+		hrtimer_start(&cdev->hrtimer,
+			      ns_to_ktime(cdev->rx_coalesce_usecs_irq * NSEC_PER_USEC),
+			      HRTIMER_MODE_REL);
+	}
+}
+
 static irqreturn_t m_can_isr(int irq, void *dev_id)
 {
 	struct net_device *dev = (struct net_device *)dev_id;
 	struct m_can_classdev *cdev = netdev_priv(dev);
 	u32 ir;
 
-	if (pm_runtime_suspended(cdev->dev))
+	if (pm_runtime_suspended(cdev->dev)) {
+		m_can_coalescing_disable(cdev);
 		return IRQ_NONE;
+	}
+
 	ir = m_can_read(cdev, M_CAN_IR);
+	m_can_coalescing_update(cdev, ir);
 	if (!ir)
 		return IRQ_NONE;
 
@@ -1114,13 +1161,17 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 	 * - state change IRQ
 	 * - bus error IRQ and bus error reporting
 	 */
-	if ((ir & IR_RF0N) || (ir & IR_ERR_ALL_30X)) {
+	if (ir & (IR_RF0N | IR_RF0W | IR_ERR_ALL_30X)) {
 		cdev->irqstatus = ir;
 		if (!cdev->is_peripheral) {
 			m_can_disable_all_interrupts(cdev);
 			napi_schedule(&cdev->napi);
-		} else if (m_can_rx_peripheral(dev, ir) < 0) {
-			goto out_fail;
+		} else {
+			int pkts;
+
+			pkts = m_can_rx_peripheral(dev, ir);
+			if (pkts < 0)
+				goto out_fail;
 		}
 	}
 
@@ -1156,6 +1207,15 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static enum hrtimer_restart m_can_coalescing_timer(struct hrtimer *timer)
+{
+	struct m_can_classdev *cdev = container_of(timer, struct m_can_classdev, hrtimer);
+
+	irq_wake_thread(cdev->net->irq, cdev->net);
+
+	return HRTIMER_NORESTART;
+}
+
 static const struct can_bittiming_const m_can_bittiming_const_30X = {
 	.name = KBUILD_MODNAME,
 	.tseg1_min = 2,		/* Time segment 1 = prop_seg + phase_seg1 */
@@ -1296,7 +1356,7 @@ static int m_can_chip_config(struct net_device *dev)
 	/* Disable unused interrupts */
 	interrupts &= ~(IR_ARA | IR_ELO | IR_DRX | IR_TEFF | IR_TEFW | IR_TFE |
 			IR_TCF | IR_HPM | IR_RF1F | IR_RF1W | IR_RF1N |
-			IR_RF0F | IR_RF0W);
+			IR_RF0F);
 
 	m_can_config_endisable(cdev, true);
 
@@ -1340,6 +1400,7 @@ static int m_can_chip_config(struct net_device *dev)
 
 	/* rx fifo configuration, blocking mode, fifo size 1 */
 	m_can_write(cdev, M_CAN_RXF0C,
+		    FIELD_PREP(RXFC_FWM_MASK, cdev->rx_max_coalesced_frames_irq) |
 		    FIELD_PREP(RXFC_FS_MASK, cdev->mcfg[MRAM_RXF0].num) |
 		    cdev->mcfg[MRAM_RXF0].off);
 
@@ -1398,7 +1459,7 @@ static int m_can_chip_config(struct net_device *dev)
 		else
 			interrupts &= ~(IR_ERR_LEC_31X);
 	}
-	m_can_write(cdev, M_CAN_IE, interrupts);
+	m_can_interrupt_enable(cdev, interrupts);
 
 	/* route all interrupts to INT0 */
 	m_can_write(cdev, M_CAN_ILS, ILS_ALL_INT0);
@@ -2082,6 +2143,9 @@ int m_can_class_register(struct m_can_classdev *cdev)
 		hrtimer_init(&cdev->hrtimer, CLOCK_MONOTONIC,
 			     HRTIMER_MODE_REL_PINNED);
 		cdev->hrtimer.function = &hrtimer_callback;
+	} else {
+		hrtimer_init(&cdev->hrtimer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+		cdev->hrtimer.function = m_can_coalescing_timer;
 	}
 
 	ret = m_can_dev_setup(cdev);
diff --git a/drivers/net/can/m_can/m_can.h b/drivers/net/can/m_can/m_can.h
index 520e14277dff..b916206199f1 100644
--- a/drivers/net/can/m_can/m_can.h
+++ b/drivers/net/can/m_can/m_can.h
@@ -92,6 +92,11 @@ struct m_can_classdev {
 	int pm_clock_support;
 	int is_peripheral;
 
+	// Cached M_CAN_IE register content
+	u32 active_interrupts;
+	u32 rx_max_coalesced_frames_irq;
+	u32 rx_coalesce_usecs_irq;
+
 	struct mram_cfg mcfg[MRAM_CFG_NUM];
 
 	struct hrtimer hrtimer;
-- 
2.40.1


  parent reply	other threads:[~2023-09-29 14:13 UTC|newest]

Thread overview: 26+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-09-29 14:12 [PATCH v6 00/14] can: m_can: Optimizations for m_can/tcan part 2 Markus Schneider-Pargmann
2023-09-29 14:12 ` [PATCH v6 01/14] can: m_can: Start/Cancel polling timer together with interrupts Markus Schneider-Pargmann
2023-10-01 12:22   ` Simon Horman
2023-09-29 14:12 ` [PATCH v6 02/14] can: m_can: Move hrtimer init to m_can_class_register Markus Schneider-Pargmann
2023-10-01 12:22   ` Simon Horman
2023-09-29 14:12 ` [PATCH v6 03/14] can: m_can: Write transmit header and data in one transaction Markus Schneider-Pargmann
2023-09-29 14:12 ` Markus Schneider-Pargmann [this message]
2023-10-01 12:23   ` [PATCH v6 04/14] can: m_can: Implement receive coalescing Simon Horman
2023-09-29 14:12 ` [PATCH v6 05/14] can: m_can: Implement transmit coalescing Markus Schneider-Pargmann
2023-10-01 12:23   ` Simon Horman
2023-09-29 14:12 ` [PATCH v6 06/14] can: m_can: Add rx coalescing ethtool support Markus Schneider-Pargmann
2023-10-01 12:23   ` Simon Horman
2023-09-29 14:12 ` [PATCH v6 07/14] can: m_can: Add tx " Markus Schneider-Pargmann
2023-10-01 12:24   ` Simon Horman
2023-09-29 14:12 ` [PATCH v6 08/14] can: m_can: Use u32 for putidx Markus Schneider-Pargmann
2023-09-29 14:12 ` [PATCH v6 09/14] can: m_can: Cache tx putidx Markus Schneider-Pargmann
2023-09-29 14:13 ` [PATCH v6 10/14] can: m_can: Use the workqueue as queue Markus Schneider-Pargmann
2023-09-29 14:13 ` [PATCH v6 11/14] can: m_can: Introduce a tx_fifo_in_flight counter Markus Schneider-Pargmann
2023-09-29 14:13 ` [PATCH v6 12/14] can: m_can: Use tx_fifo_in_flight for netif_queue control Markus Schneider-Pargmann
2023-09-29 14:13 ` [PATCH v6 13/14] can: m_can: Implement BQL Markus Schneider-Pargmann
2023-09-29 14:13 ` [PATCH v6 14/14] can: m_can: Implement transmit submission coalescing Markus Schneider-Pargmann
2023-10-17  8:44 ` [PATCH v6 00/14] can: m_can: Optimizations for m_can/tcan part 2 Markus Schneider-Pargmann
2023-11-13 13:25 ` Martin Hundebøll
2023-11-13 13:30   ` Marc Kleine-Budde
2023-11-13 13:31     ` Martin Hundebøll
2023-11-13 20:51       ` Markus Schneider-Pargmann

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230929141304.3934380-5-msp@baylibre.com \
    --to=msp@baylibre.com \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=jm@ti.com \
    --cc=jpanis@baylibre.com \
    --cc=kuba@kernel.org \
    --cc=linux-can@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mailhol.vincent@wanadoo.fr \
    --cc=mkl@pengutronix.de \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=rcsekar@samsung.com \
    --cc=simon.horman@corigine.com \
    --cc=wg@grandegger.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox