[RESEND PATCH v4 0/7] Fixes and improvements for RS485 (RESEND)

[RESEND PATCH v4 0/7] Fixes and improvements for RS485 (RESEND)

[Lino Sanfilippo]

Changes in v4:

- add comment for function uart_set_rs485_gpios after hint from Hugo
- correct commit message as pointed out by Hugo
- rephrase commit messages
- add patch 7 after discussion with Ilpo

Changes in v3
- Drop patch "Get rid of useless wrapper pl011_get_rs485_mode()" as
  requested by Greg

Changes in v2:
- add missing 'Fixes' tags as requested by Greg
- corrected a typo as pointed out by Hugo
- fix issue in imx driver in the serial core as suggested by Uwe
- partly rephrase some commit messages
- add patch 7

Lino Sanfilippo (7):
  serial: Do not hold the port lock when setting rx-during-tx GPIO
  serial: core: set missing supported flag for RX during TX GPIO
  serial: core: fix sanitizing check for RTS settings
  serial: core: make sure RS485 cannot be enabled when it is not
    supported
  serial: core, imx: do not set RS485 enabled if it is not supported
  serial: omap: do not override settings for RS485 support
  serial: 8250_exar: Set missing rs485_supported flag

 drivers/tty/serial/8250/8250_exar.c |  5 +--
 drivers/tty/serial/imx.c            |  8 -----
 drivers/tty/serial/omap-serial.c    |  8 ++---
 drivers/tty/serial/serial_core.c    | 53 +++++++++++++++++++++--------
 drivers/tty/serial/stm32-usart.c    |  5 +--
 5 files changed, 46 insertions(+), 33 deletions(-)


base-commit: b85ea95d086471afb4ad062012a4d73cd328fa86
-- 
2.42.0

[RESEND PATCH v4 1/7] serial: Do not hold the port lock when setting rx-during-tx GPIO

[Lino Sanfilippo]

Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be an
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).

Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.

Since both setting the term and the rx-during-tx GPIO is done at the same
code place, move it into a common function.

Fixes: c54d48543689 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
Fixes: ca530cfa968c ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/imx.c         |  4 ----
 drivers/tty/serial/serial_core.c | 15 +++++++++++----
 drivers/tty/serial/stm32-usart.c |  5 +----
 3 files changed, 12 insertions(+), 12 deletions(-)

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 708b9852a575..9cffeb23112b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1943,10 +1943,6 @@ static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termio
 	    rs485conf->flags & SER_RS485_RX_DURING_TX)
 		imx_uart_start_rx(port);
 
-	if (port->rs485_rx_during_tx_gpio)
-		gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
-					 !!(rs485conf->flags & SER_RS485_RX_DURING_TX));
-
 	return 0;
 }
 
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index f1348a509552..ab766f48c172 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1392,14 +1392,21 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4
 	memset(rs485->padding1, 0, sizeof(rs485->padding1));
 }
 
-static void uart_set_rs485_termination(struct uart_port *port,
-				       const struct serial_rs485 *rs485)
+/*
+ * Set optional RS485 GPIOs for bus termination and data reception during
+ * transmission. These GPIOs are controlled by the serial core independently
+ * from the UART driver.
+ */
+static void uart_set_rs485_gpios(struct uart_port *port,
+				 const struct serial_rs485 *rs485)
 {
 	if (!(rs485->flags & SER_RS485_ENABLED))
 		return;
 
 	gpiod_set_value_cansleep(port->rs485_term_gpio,
 				 !!(rs485->flags & SER_RS485_TERMINATE_BUS));
+	gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
+				 !!(rs485->flags & SER_RS485_RX_DURING_TX));
 }
 
 static int uart_rs485_config(struct uart_port *port)
@@ -1412,7 +1419,7 @@ static int uart_rs485_config(struct uart_port *port)
 		return 0;
 
 	uart_sanitize_serial_rs485(port, rs485);
-	uart_set_rs485_termination(port, rs485);
+	uart_set_rs485_gpios(port, rs485);
 
 	uart_port_lock_irqsave(port, &flags);
 	ret = port->rs485_config(port, NULL, rs485);
@@ -1456,7 +1463,7 @@ static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
 	if (ret)
 		return ret;
 	uart_sanitize_serial_rs485(port, &rs485);
-	uart_set_rs485_termination(port, &rs485);
+	uart_set_rs485_gpios(port, &rs485);
 
 	uart_port_lock_irqsave(port, &flags);
 	ret = port->rs485_config(port, &tty->termios, &rs485);
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 3048620315d6..ec9a72a5bea9 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -226,10 +226,7 @@ static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *ter
 
 	stm32_usart_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
 
-	if (port->rs485_rx_during_tx_gpio)
-		gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
-					 !!(rs485conf->flags & SER_RS485_RX_DURING_TX));
-	else
+	if (!port->rs485_rx_during_tx_gpio)
 		rs485conf->flags |= SER_RS485_RX_DURING_TX;
 
 	if (rs485conf->flags & SER_RS485_ENABLED) {
-- 
2.42.0

Re: [RESEND PATCH v4 1/7] serial: Do not hold the port lock when setting rx-during-tx GPIO

[Lino Sanfilippo]

On 19.11.23 12:28, Lino Sanfilippo wrote:
> Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
> Since this function is called with the port lock held, this can be an
> problem in case that setting the GPIO line can sleep (e.g. if a GPIO
> expander is used which is connected via SPI or I2C).
> 
> Avoid this issue by moving the GPIO setting outside of the port lock into
> the serial core and thus making it a generic feature.
> 
> Since both setting the term and the rx-during-tx GPIO is done at the same
> code place, move it into a common function.

> -				       const struct serial_rs485 *rs485)
> +/*
> + * Set optional RS485 GPIOs for bus termination and data reception during
> + * transmission. These GPIOs are controlled by the serial core independently
> + * from the UART driver.
> + */
> +static void uart_set_rs485_gpios(struct uart_port *port,
> +				 const struct serial_rs485 *rs485)
>  {
>  	if (!(rs485->flags & SER_RS485_ENABLED))
>  		return;
>  
>  	gpiod_set_value_cansleep(port->rs485_term_gpio,
>  				 !!(rs485->flags & SER_RS485_TERMINATE_BUS));
> +	gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
> +				 !!(rs485->flags & SER_RS485_RX_DURING_TX));
>  }
>  

Rasmus is about to add support for another RS485 related GPIO (see 
https://lore.kernel.org/all/20231120151056.148450-3-linux@rasmusvillemoes.dk/ )
which has to be configured both before and after port->rs485_config(). This
does not fit very well with the idea of handling all these GPIOs in
one function. 

So I would like to revise this patch and send an updated version in a v5
of this series in which the suggestion from Hugo
(see https://lore.kernel.org/all/20231011183656.5111ba32ec0c9d43171662a1@hugovil.com/)
is implemented to use separate functions for the GPIO configurations.

Regards,
Lino

Re: [RESEND PATCH v4 1/7] serial: Do not hold the port lock when setting rx-during-tx GPIO

[Greg KH]

On Wed, Nov 22, 2023 at 12:55:49PM +0100, Lino Sanfilippo wrote:
> 
> 
> On 19.11.23 12:28, Lino Sanfilippo wrote:
> > Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
> > Since this function is called with the port lock held, this can be an
> > problem in case that setting the GPIO line can sleep (e.g. if a GPIO
> > expander is used which is connected via SPI or I2C).
> > 
> > Avoid this issue by moving the GPIO setting outside of the port lock into
> > the serial core and thus making it a generic feature.
> > 
> > Since both setting the term and the rx-during-tx GPIO is done at the same
> > code place, move it into a common function.
> 
> > -				       const struct serial_rs485 *rs485)
> > +/*
> > + * Set optional RS485 GPIOs for bus termination and data reception during
> > + * transmission. These GPIOs are controlled by the serial core independently
> > + * from the UART driver.
> > + */
> > +static void uart_set_rs485_gpios(struct uart_port *port,
> > +				 const struct serial_rs485 *rs485)
> >  {
> >  	if (!(rs485->flags & SER_RS485_ENABLED))
> >  		return;
> >  
> >  	gpiod_set_value_cansleep(port->rs485_term_gpio,
> >  				 !!(rs485->flags & SER_RS485_TERMINATE_BUS));
> > +	gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
> > +				 !!(rs485->flags & SER_RS485_RX_DURING_TX));
> >  }
> >  
> 
> Rasmus is about to add support for another RS485 related GPIO (see 
> https://lore.kernel.org/all/20231120151056.148450-3-linux@rasmusvillemoes.dk/ )
> which has to be configured both before and after port->rs485_config(). This
> does not fit very well with the idea of handling all these GPIOs in
> one function. 
> 
> So I would like to revise this patch and send an updated version in a v5
> of this series in which the suggestion from Hugo
> (see https://lore.kernel.org/all/20231011183656.5111ba32ec0c9d43171662a1@hugovil.com/)
> is implemented to use separate functions for the GPIO configurations.
> 

I'll drop this, thanks for letting me know.

There are WAY too many different "enable 485 in this way" patches that
are all conflicting with each other.  Can you all decide on a common way
to handle this, otherwise none of these are going to be acceptable :(

thanks,

greg k-h

[RESEND PATCH v4 2/7] serial: core: set missing supported flag for RX during TX GPIO

[Lino Sanfilippo]

If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.

Cc: stable@vger.kernel.org
Fixes: 163f080eb717 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/serial_core.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index ab766f48c172..af175c803c22 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -3627,6 +3627,8 @@ int uart_get_rs485_mode(struct uart_port *port)
 	if (IS_ERR(desc))
 		return dev_err_probe(dev, PTR_ERR(desc), "Cannot get rs485-rx-during-tx-gpios\n");
 	port->rs485_rx_during_tx_gpio = desc;
+	if (port->rs485_rx_during_tx_gpio)
+		port->rs485_supported.flags |= SER_RS485_RX_DURING_TX;
 
 	return 0;
 }
-- 
2.42.0

[RESEND PATCH v4 3/7] serial: core: fix sanitizing check for RTS settings

[Lino Sanfilippo]

Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.

This however makes only sense if both RTS modes are actually supported by
the driver.

With commit be2e2cb1d281 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.

Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.

Cc: stable@vger.kernel.org
Fixes: be2e2cb1d281 ("serial: Sanitize rs485_struct")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/serial_core.c | 28 ++++++++++++++++++----------
 1 file changed, 18 insertions(+), 10 deletions(-)

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index af175c803c22..b96fc2ba8596 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1371,19 +1371,27 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4
 		return;
 	}
 
+	rs485->flags &= supported_flags;
+
 	/* Pick sane settings if the user hasn't */
-	if ((supported_flags & (SER_RS485_RTS_ON_SEND|SER_RS485_RTS_AFTER_SEND)) &&
-	    !(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+	if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
 	    !(rs485->flags & SER_RS485_RTS_AFTER_SEND)) {
-		dev_warn_ratelimited(port->dev,
-			"%s (%d): invalid RTS setting, using RTS_ON_SEND instead\n",
-			port->name, port->line);
-		rs485->flags |= SER_RS485_RTS_ON_SEND;
-		rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
-		supported_flags |= SER_RS485_RTS_ON_SEND|SER_RS485_RTS_AFTER_SEND;
-	}
+		if (supported_flags & SER_RS485_RTS_ON_SEND) {
+			rs485->flags |= SER_RS485_RTS_ON_SEND;
+			rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
 
-	rs485->flags &= supported_flags;
+			dev_warn_ratelimited(port->dev,
+				"%s (%d): invalid RTS setting, using RTS_ON_SEND instead\n",
+				port->name, port->line);
+		} else {
+			rs485->flags |= SER_RS485_RTS_AFTER_SEND;
+			rs485->flags &= ~SER_RS485_RTS_ON_SEND;
+
+			dev_warn_ratelimited(port->dev,
+				"%s (%d): invalid RTS setting, using RTS_AFTER_SEND instead\n",
+				port->name, port->line);
+		}
+	}
 
 	uart_sanitize_serial_rs485_delays(port, rs485);
 
-- 
2.42.0

[RESEND PATCH v4 4/7] serial: core: make sure RS485 cannot be enabled when it is not supported

[Lino Sanfilippo]

Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).

In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.

Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.

Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.

Fixes: e849145e1fdd ("serial: ar933x: Fill in rs485_supported")
Fixes: 55e18c6b6d42 ("serial: imx: Remove serial_rs485 sanitization")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/serial_core.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index b96fc2ba8596..b636e2ce6e8b 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1444,6 +1444,9 @@ static int uart_get_rs485_config(struct uart_port *port,
 	unsigned long flags;
 	struct serial_rs485 aux;
 
+	if (!(port->rs485_supported.flags & SER_RS485_ENABLED))
+		return -ENOTTY;
+
 	uart_port_lock_irqsave(port, &flags);
 	aux = port->rs485;
 	uart_port_unlock_irqrestore(port, flags);
@@ -1461,7 +1464,7 @@ static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
 	int ret;
 	unsigned long flags;
 
-	if (!port->rs485_config)
+	if (!(port->rs485_supported.flags & SER_RS485_ENABLED))
 		return -ENOTTY;
 
 	if (copy_from_user(&rs485, rs485_user, sizeof(*rs485_user)))
-- 
2.42.0

[RESEND PATCH v4 5/7] serial: core, imx: do not set RS485 enabled if it is not supported

[Lino Sanfilippo]

If the imx driver cannot support RS485 it sets the ports rs485_supported
structure to NULL. But it still calls uart_get_rs485_mode() which may set
the RS485_ENABLED flag nevertheless.

This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.

Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.

With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. Remove this check, too.

Fixes: 00d7a00e2a6f ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/imx.c         | 4 ----
 drivers/tty/serial/serial_core.c | 3 +++
 2 files changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 9cffeb23112b..98b78d360a74 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -2328,10 +2328,6 @@ static int imx_uart_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	if (sport->port.rs485.flags & SER_RS485_ENABLED &&
-	    (!sport->have_rtscts && !sport->have_rtsgpio))
-		dev_err(&pdev->dev, "no RTS control, disabling rs485\n");
-
 	/*
 	 * If using the i.MX UART RTS/CTS control then the RTS (CTS_B)
 	 * signal cannot be set low during transmission in case the
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index b636e2ce6e8b..518e19036983 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -3588,6 +3588,9 @@ int uart_get_rs485_mode(struct uart_port *port)
 	u32 rs485_delay[2];
 	int ret;
 
+	if (!(port->rs485_supported.flags & SER_RS485_ENABLED))
+		return 0;
+
 	ret = device_property_read_u32_array(dev, "rs485-rts-delay",
 					     rs485_delay, 2);
 	if (!ret) {
-- 
2.42.0

[RESEND PATCH v4 6/7] serial: omap: do not override settings for RS485 support

[Lino Sanfilippo]

In serial_omap_rs485() RS485 support may be deactivated due to a missing
RTS GPIO. This is done by nullifying the ports rs485_supported struct.
After that however the serial_omap_rs485_supported struct is assigned to
the same structure unconditionally, which results in an unintended
reactivation of RS485 support.
Fix this by callling serial_omap_rs485() after the assignment of
rs485_supported.

Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/omap-serial.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index ad4c1c5d0a7f..d9b2936308c4 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1604,10 +1604,6 @@ static int serial_omap_probe(struct platform_device *pdev)
 		dev_info(up->port.dev, "no wakeirq for uart%d\n",
 			 up->port.line);
 
-	ret = serial_omap_probe_rs485(up, &pdev->dev);
-	if (ret < 0)
-		goto err_rs485;
-
 	sprintf(up->name, "OMAP UART%d", up->port.line);
 	up->port.mapbase = mem->start;
 	up->port.membase = base;
@@ -1622,6 +1618,10 @@ static int serial_omap_probe(struct platform_device *pdev)
 			 DEFAULT_CLK_SPEED);
 	}
 
+	ret = serial_omap_probe_rs485(up, &pdev->dev);
+	if (ret < 0)
+		goto err_rs485;
+
 	up->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
 	up->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
 	cpu_latency_qos_add_request(&up->pm_qos_request, up->latency);
-- 
2.42.0

[RESEND PATCH v4 7/7] serial: 8250_exar: Set missing rs485_supported flag

[Lino Sanfilippo]

The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.

Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).

Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
---
 drivers/tty/serial/8250/8250_exar.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 6085d356ad86..23366f868ae3 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -480,7 +480,7 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio
 }
 
 static const struct serial_rs485 generic_rs485_supported = {
-	.flags = SER_RS485_ENABLED,
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
 };
 
 static const struct exar8250_platform exar8250_default_platform = {
@@ -524,7 +524,8 @@ static int iot2040_rs485_config(struct uart_port *port, struct ktermios *termios
 }
 
 static const struct serial_rs485 iot2040_rs485_supported = {
-	.flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+		 SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
 };
 
 static const struct property_entry iot2040_gpio_properties[] = {
-- 
2.42.0