[PATCH 3/3] dts: arm64: sunxi: add initial dts for T95 AXP313 tv box

[Kamil Kasperski <ressetkk@gmail.com>]

T95 is a most commonly known for being a box with a pre-installed malware.
It uses Allwinner H616 and comes with eMMC and DDR3 memory.

Those TV boxes usually come with common hardware:
- Allwinner H616 SoC
- 2/4 GB DDR3 SDRAM (Hynix H5TQ2G43BFR)
- 16/32/64 GB eMMC
- microSD slot
- AXP305 or AXP313 PMIC depending on board revision
- 3.5mm A/V output
- HDMI port
- 2x USB 2.0 ports
- 100M ETH using Internal PHY
- 7-segment display
- DC 5V barrel jack port

The board contains holes hor UART header wired to &uart0.
From the DRAM specification its operation voltage is 1.5V.

Signed-off-by: Kamil Kasperski <ressetkk@gmail.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h616-t95-axp313.dts  | 138 ++++++++++++++++++
 2 files changed, 139 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-t95-axp313.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 21149b346a60..183dcdea40ad 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -43,6 +43,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-t95-axp313.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-t95-axp313.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-t95-axp313.dts
new file mode 100644
index 000000000000..830a8815e675
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-t95-axp313.dts
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Kamil Kasperski <ressetkk@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "T95 5G (AXP313)";
+	compatible = "t95,t95-axp313", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	broken-cd;
+	vmmc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>;	/* PC9 */
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			/* Supplies VCC-PLL, so needs to be always on. */
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Supplies VCC-IO, so needs to be always on. */
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "host";	/* USB A type receptable */
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
2.34.1