From: "manivannan.sadhasivam@linaro.org" <manivannan.sadhasivam@linaro.org>
To: mank <mank@netprisma.us>
Cc: "duke_xinanwen@163.com" <duke_xinanwen@163.com>,
"loic.poulain@linaro.org" <loic.poulain@linaro.org>,
"quic_qianyu@quicinc.com" <quic_qianyu@quicinc.com>,
"mhi@lists.linux.dev" <mhi@lists.linux.dev>,
"linux-arm-msm@vger.kernel.org" <linux-arm-msm@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH V2] bus: mhi: host: pci_generic: Add support for Netprisma LCUR57 and FCUN69
Date: Wed, 5 Jun 2024 12:46:48 +0530 [thread overview]
Message-ID: <20240605071648.GA5085@thinkpad> (raw)
In-Reply-To: <LV3PR22MB5104E2E4AD0A22D1B8FD2AAAB0F92@LV3PR22MB5104.namprd22.prod.outlook.com>
On Wed, Jun 05, 2024 at 07:01:17AM +0000, mank wrote:
> Add Netprisma LCUR57 and FCUN69 hardware revision:
>
> LCUR57:
> 02:00.0 Unassigned class [ff00]: Device 203e:1000
> Subsystem: Device 203e:1000
>
> FCUN69:
> 02:00.0 Unassigned class [ff00]: Device 203e:1001
> Subsystem: Device 203e:1001
>
> ---
> V1 -> V2:
> 1.Change 0x203E to 0x203e
> 2.Remove redundant code and use existing config:modem_quectel_em1xx_config
>
> Signed-off-by: Mank Wang <mank@netprisma.us>
> ---
> drivers/bus/mhi/host/pci_generic.c | 29 +++++++++++++++++++++++++++++
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Mani
> 1 file changed, 29 insertions(+)
>
> diff --git a/drivers/bus/mhi/host/pci_generic.c b/drivers/bus/mhi/host/pci_generic.c
> index 08844ee79654..21c1d750274c 100644
> --- a/drivers/bus/mhi/host/pci_generic.c
> +++ b/drivers/bus/mhi/host/pci_generic.c
> @@ -26,6 +26,7 @@
> /* PCI VID definitions */
> #define PCI_VENDOR_ID_THALES 0x1269
> #define PCI_VENDOR_ID_QUECTEL 0x1eac
> +#define PCI_VENDOR_ID_NETPRISMA 0x203e
>
> #define MHI_EDL_DB 91
> #define MHI_EDL_COOKIE 0xEDEDEDED
> @@ -606,6 +607,28 @@ static const struct mhi_pci_dev_info mhi_telit_fn990_info = {
> .mru_default = 32768,
> };
>
> +static const struct mhi_pci_dev_info mhi_netprisma_lcur57_info = {
> + .name = "netprisma-lcur57",
> + .edl = "qcom/prog_firehose_sdx24.mbn",
> + /* LCUR57 uses the same controller configuration as quectel_em1xx */
> + .config = &modem_quectel_em1xx_config,
> + .bar_num = MHI_PCI_DEFAULT_BAR_NUM,
> + .dma_data_width = 32,
> + .mru_default = 32768,
> + .sideband_wake = true,
> +};
> +
> +static const struct mhi_pci_dev_info mhi_netprisma_fcun69_info = {
> + .name = "netprisma-fcun69",
> + .edl = "qcom/prog_firehose_sdx6x.elf",
> + /* FCUN69 uses the same controller configuration as quectel_em1xx */
> + .config = &modem_quectel_em1xx_config,
> + .bar_num = MHI_PCI_DEFAULT_BAR_NUM,
> + .dma_data_width = 32,
> + .mru_default = 32768,
> + .sideband_wake = true,
> +};
> +
> /* Keep the list sorted based on the PID. New VID should be added as the last entry */
> static const struct pci_device_id mhi_pci_id_table[] = {
> { PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x0304),
> @@ -695,6 +718,12 @@ static const struct pci_device_id mhi_pci_id_table[] = {
> /* T99W175 (sdx55), HP variant */
> { PCI_DEVICE(0x03f0, 0x0a6c),
> .driver_data = (kernel_ulong_t) &mhi_foxconn_sdx55_info },
> + /* NETPRISMA LCUR57 (SDX24) */
> + { PCI_DEVICE(PCI_VENDOR_ID_NETPRISMA, 0x1000),
> + .driver_data = (kernel_ulong_t) &mhi_netprisma_lcur57_info },
> + /* NETPRISMA FCUN69 (SDX6X) */
> + { PCI_DEVICE(PCI_VENDOR_ID_NETPRISMA, 0x1001),
> + .driver_data = (kernel_ulong_t) &mhi_netprisma_fcun69_info },
> { }
> };
> MODULE_DEVICE_TABLE(pci, mhi_pci_id_table);
> --
> 2.34.1
>
--
மணிவண்ணன் சதாசிவம்
next prev parent reply other threads:[~2024-06-05 7:16 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-05 7:01 [PATCH V2] bus: mhi: host: pci_generic: Add support for Netprisma LCUR57 and FCUN69 mank
2024-06-05 7:16 ` manivannan.sadhasivam [this message]
-- strict thread matches above, loose matches on Subject: below --
2024-08-27 1:58 Mank Wang
2024-08-27 8:30 ` manivannan.sadhasivam
2024-08-27 8:32 ` manivannan.sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240605071648.GA5085@thinkpad \
--to=manivannan.sadhasivam@linaro.org \
--cc=duke_xinanwen@163.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=loic.poulain@linaro.org \
--cc=mank@netprisma.us \
--cc=mhi@lists.linux.dev \
--cc=quic_qianyu@quicinc.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).