Re: [PATCH v2 1/1] dt-bindings: extcon: ptn5150: add child node port

[Rob Herring <robh@kernel.org>]

On Thu, Aug 15, 2024 at 04:32:44PM -0400, Frank Li wrote:
> Add child node 'port' to allow connect to usb controller to do role-switch.
> Add example for id pin of ptn5150 have not connect to main chip's usb id
> pin.
> 
> Fix below warning:
> arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dtb: typec@3d: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
>         from schema $id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> Change from v1 to v2
> - add example for id pin have not connect to main chip's id example.
> - commit 095b96b2b fix "port" warning, but add new warning "connector" is
> not exist. And follow commit revert this change.
> 690085d866f08 Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector
> - I have not board in hand to debug why "connector" is not work.
> ---
>  .../bindings/extcon/extcon-ptn5150.yaml       | 46 +++++++++++++++++++
>  1 file changed, 46 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
> index d5cfa32ea52dd..39231f9952826 100644
> --- a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
> +++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
> @@ -37,6 +37,11 @@ properties:
>        GPIO pin (output) used to control VBUS. If skipped, no such control
>        takes place.
>  
> +  port:
> +    $ref: /schemas/graph.yaml#/properties/port
> +    description:
> +      A port node to link the usb controller for the dual role switch.
> +
>  required:
>    - compatible
>    - interrupts
> @@ -60,3 +65,44 @@ examples:
>              vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
>          };
>      };
> +
> +  - |
> +    /* id pin of ptn5150 have not connected to chip's id pin */
> +    #include <dt-bindings/clock/imx8mn-clock.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/gpio/gpio.h>

Just add 'port' to the existing example if you want to. Don't need a 
whole other example just for that.

> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        ptn5150@1d {
> +            compatible = "nxp,ptn5150";
> +            reg = <0x1d>;
> +            interrupt-parent = <&msmgpio>;
> +            interrupts = <78 IRQ_TYPE_LEVEL_HIGH>;
> +            vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
> +
> +            port {
> +                    typec1_dr_sw: endpoint {
> +                    remote-endpoint = <&usb1_drd_sw>;
> +                 };
> +            };
> +        };
> +    };
> +
> +    usb@32e40000 {
> +        compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb", "fsl,imx27-usb";
> +        reg = <0x32e40000 0x200>;
> +        interrupts = <&gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> +        clocks = <&clk IMX8MN_CLK_USB1_CTRL_ROOT>;
> +        usb-role-switch;
> +
> +        port {
> +             usb1_drd_sw: endpoint {
> +                  remote-endpoint = <&typec1_dr_sw>;
> +             };
> +        };
> +    };
> +
> -- 
> 2.34.1
>