Re: [PATCH] ARM: dts: microchip: sam9x60: Add missing property atmel,usart-mode

Nicolas Ferre
2024-09-05T14:36:55Z

On 05/09/2024 at 11:30, Andrei Simion wrote:
> ~: make dtbs_check DT_SCHEMA_FILES=atmel,at91-usart.ymal
> -> for all boards which inherit sam9x60.dtsi: serial@200: $nodename:0:
> 'serial@200' does not match '^spi(@.*|-([0-9]|[1-9][0-9]+))?$
> serial@200: atmel,use-dma-rx: False schema does not allow True
> serial@200: atmel,use-dma-tx: False schema does not allow True
> serial@200: atmel,fifo-size: False schema does not allow [[16]]
> -> Means : atmel,usart-mode = <AT91_USART_MODE_SERIAL> misses for uart:
> 0,1,2,3,4,6,7,8,9,10,11,12
>
> Add to uart nodes the property atmel,usart-mode to specify the driver to be
> used in serial mode to be compliant to atmel,at91-usart.yaml.
>
> Fixes: 99c808335877 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions")
> Signed-off-by: Andrei Simion <andrei.simion@microchip.com>

Thanks Andrei:
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>

Best regards,
Nicolas

> ---
> arch/arm/boot/dts/microchip/sam9x60.dtsi | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/arch/arm/boot/dts/microchip/sam9x60.dtsi b/arch/arm/boot/dts/microchip/sam9x60.dtsi
> index 04a6d716ecaf..0ba424bba7cc 100644
> --- a/arch/arm/boot/dts/microchip/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/microchip/sam9x60.dtsi
> @@ -174,6 +174,7 @@ flx4: flexcom@f0000000 {
> uart4: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -376,6 +377,7 @@ flx11: flexcom@f0020000 {
> uart11: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -427,6 +429,7 @@ flx12: flexcom@f0024000 {
> uart12: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -586,6 +589,7 @@ flx6: flexcom@f8010000 {
> uart6: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -637,6 +641,7 @@ flx7: flexcom@f8014000 {
> uart7: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -688,6 +693,7 @@ flx8: flexcom@f8018000 {
> uart8: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -739,6 +745,7 @@ flx0: flexcom@f801c000 {
> uart0: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -809,6 +816,7 @@ flx1: flexcom@f8020000 {
> uart1: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -879,6 +887,7 @@ flx2: flexcom@f8024000 {
> uart2: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -949,6 +958,7 @@ flx3: flexcom@f8028000 {
> uart3: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -1074,6 +1084,7 @@ flx9: flexcom@f8040000 {
> uart9: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
> @@ -1125,6 +1136,7 @@ flx10: flexcom@f8044000 {
> uart10: serial@200 {
> compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> reg = <0x200 0x200>;
> + atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
> dmas = <&dma0
> (AT91_XDMAC_DT_MEM_IF(0) |
>
> base-commit: fdadd93817f124fd0ea6ef251d4a1068b7feceba