[PATCH v6 0/5] mfd: tqmx86: new hardware and GPIO/I2C IRQ improvements/additions

[PATCH v6 0/5] mfd: tqmx86: new hardware and GPIO/I2C IRQ improvements/additions

[Matthias Schiffer]

Patch 1 adds support for 3 new TQMx86 COMs. GPIO support on SMARC
modules is currently limited (not all GPIOs can be controlled, pins use
incorrect default directions, IRQ configuration is handled incorrectly),
however this is a preexisting issue also effecting the TQMxE39S and
TQMxE40S, not only the new TQMxE41S. This will be addressed by a future
patch series involving both the TQMx86 MFD and GPIO drivers.

Patches 2-5 improve module parameter description and error handling of
GPIO IRQ configuration and add support for configuring an IRQ for the
TQMx86's OpenCores I2C controller in the same way.

Changelog:

v2: improve module parameter description (new patch 2, adjusted patch 5)
v3: replace IRQ 0 resource entries with empty placeholders to simplify
    error handling (patches 4 and 5)
v4: remove tqmx86_irq_to_irq_cfg() function (patch 3)
v5: move placeholders to the end of the resource arrays, use defines for
    index (patches 4 and 5)
v6: remove obsolete comment; refer to I2C controller as I2C1 (patch 5)

Gregor Herburger (1):
  mfd: tqmx86: add I2C IRQ support

Matthias Schiffer (4):
  mfd: tqmx86: add board definitions for TQMx120UC, TQMx130UC and
    TQMxE41S
  mfd: tqmx86: improve gpio_irq module parameter description
  mfd: tqmx86: refactor GPIO IRQ setup
  mfd: tqmx86: make IRQ setup errors non-fatal

 drivers/mfd/tqmx86.c | 105 +++++++++++++++++++++++++++++--------------
 1 file changed, 71 insertions(+), 34 deletions(-)

-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/

[PATCH v6 1/5] mfd: tqmx86: add board definitions for TQMx120UC, TQMx130UC and TQMxE41S

[Matthias Schiffer]

This adds support for 3 new TQMx86 COMs:

- TQMx120UC/TQMx130UC: COM Express Compact Type 6 modules with 12th and
  13th Generation Intel Core CPUs ([1, 2])
- TQMxE41S: SMARC 2.1 module with Intel Atom x7000E and compatible CPUs [3]

[1] https://www.tq-group.com/en/products/tq-embedded/x86-architecture/tqmx120uc/
[2] https://www.tq-group.com/en/products/tq-embedded/x86-architecture/tqmx130uc/
[3] https://www.tq-group.com/en/products/tq-embedded/x86-architecture/tqmxe41s/

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
---

v2: no changes
v3: no changes
v4: no changes
v5: no changes
v6: no changes

 drivers/mfd/tqmx86.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
index fac02875fe7d9..e15b9be98c2db 100644
--- a/drivers/mfd/tqmx86.c
+++ b/drivers/mfd/tqmx86.c
@@ -35,11 +35,14 @@
 #define TQMX86_REG_BOARD_ID_E39C2	7
 #define TQMX86_REG_BOARD_ID_70EB	8
 #define TQMX86_REG_BOARD_ID_80UC	9
+#define TQMX86_REG_BOARD_ID_120UC	10
 #define TQMX86_REG_BOARD_ID_110EB	11
 #define TQMX86_REG_BOARD_ID_E40M	12
 #define TQMX86_REG_BOARD_ID_E40S	13
 #define TQMX86_REG_BOARD_ID_E40C1	14
 #define TQMX86_REG_BOARD_ID_E40C2	15
+#define TQMX86_REG_BOARD_ID_130UC	16
+#define TQMX86_REG_BOARD_ID_E41S	19
 #define TQMX86_REG_BOARD_REV	0x01
 #define TQMX86_REG_IO_EXT_INT	0x06
 #define TQMX86_REG_IO_EXT_INT_NONE		0
@@ -132,6 +135,8 @@ static const char *tqmx86_board_id_to_name(u8 board_id, u8 sauc)
 		return "TQMx70EB";
 	case TQMX86_REG_BOARD_ID_80UC:
 		return "TQMx80UC";
+	case TQMX86_REG_BOARD_ID_120UC:
+		return "TQMx120UC";
 	case TQMX86_REG_BOARD_ID_110EB:
 		return "TQMx110EB";
 	case TQMX86_REG_BOARD_ID_E40M:
@@ -142,6 +147,10 @@ static const char *tqmx86_board_id_to_name(u8 board_id, u8 sauc)
 		return "TQMxE40C1";
 	case TQMX86_REG_BOARD_ID_E40C2:
 		return "TQMxE40C2";
+	case TQMX86_REG_BOARD_ID_130UC:
+		return "TQMx130UC";
+	case TQMX86_REG_BOARD_ID_E41S:
+		return "TQMxE41S";
 	default:
 		return "Unknown";
 	}
@@ -154,11 +163,14 @@ static int tqmx86_board_id_to_clk_rate(struct device *dev, u8 board_id)
 	case TQMX86_REG_BOARD_ID_60EB:
 	case TQMX86_REG_BOARD_ID_70EB:
 	case TQMX86_REG_BOARD_ID_80UC:
+	case TQMX86_REG_BOARD_ID_120UC:
 	case TQMX86_REG_BOARD_ID_110EB:
 	case TQMX86_REG_BOARD_ID_E40M:
 	case TQMX86_REG_BOARD_ID_E40S:
 	case TQMX86_REG_BOARD_ID_E40C1:
 	case TQMX86_REG_BOARD_ID_E40C2:
+	case TQMX86_REG_BOARD_ID_130UC:
+	case TQMX86_REG_BOARD_ID_E41S:
 		return 24000;
 	case TQMX86_REG_BOARD_ID_E39MS:
 	case TQMX86_REG_BOARD_ID_E39C1:
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/

[PATCH v6 2/5] mfd: tqmx86: improve gpio_irq module parameter description

[Matthias Schiffer]

Clarify that "7, 9, 12" refers to the valid arguments that can be
passed as gpio_irq.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
---

v2: new patch
v3: no changes
v4: no changes
v5: no changes
v6: no changes

 drivers/mfd/tqmx86.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
index e15b9be98c2db..7b2f9490a9af5 100644
--- a/drivers/mfd/tqmx86.c
+++ b/drivers/mfd/tqmx86.c
@@ -58,7 +58,7 @@
 
 static uint gpio_irq;
 module_param(gpio_irq, uint, 0);
-MODULE_PARM_DESC(gpio_irq, "GPIO IRQ number (7, 9, 12)");
+MODULE_PARM_DESC(gpio_irq, "GPIO IRQ number (valid parameters: 7, 9, 12)");
 
 static const struct resource tqmx_i2c_soft_resources[] = {
 	DEFINE_RES_IO(TQMX86_IOBASE_I2C, TQMX86_IOSIZE_I2C),
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/

[PATCH v6 3/5] mfd: tqmx86: refactor GPIO IRQ setup

[Matthias Schiffer]

Move IRQ setup into a helper function. The string "GPIO" for error
messages is replaced with a label argument to prepare for reusing the
function for the I2C IRQ.

No functional change intended.

Co-developed-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
---

v2: no changes (was patch 2/4)
v3: no changes
v4: drop tqmx86_irq_to_irq_cfg() function, handle IRQ-to-register-value
    mapping in tqmx86_setup_irq() instead
v5: no changes
v6: no changes

 drivers/mfd/tqmx86.c | 59 +++++++++++++++++++++++++++-----------------
 1 file changed, 37 insertions(+), 22 deletions(-)

diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
index 7b2f9490a9af5..8aa448a67c9a5 100644
--- a/drivers/mfd/tqmx86.c
+++ b/drivers/mfd/tqmx86.c
@@ -186,33 +186,52 @@ static int tqmx86_board_id_to_clk_rate(struct device *dev, u8 board_id)
 	}
 }
 
-static int tqmx86_probe(struct platform_device *pdev)
+static int tqmx86_setup_irq(struct device *dev, const char *label, u8 irq,
+			    void __iomem *io_base, u8 reg_shift)
 {
-	u8 board_id, sauc, rev, i2c_det, io_ext_int_val;
-	struct device *dev = &pdev->dev;
-	u8 gpio_irq_cfg, readback;
-	const char *board_name;
-	void __iomem *io_base;
-	int err;
+	u8 val, readback;
+	int irq_cfg;
 
-	switch (gpio_irq) {
+	switch (irq) {
 	case 0:
-		gpio_irq_cfg = TQMX86_REG_IO_EXT_INT_NONE;
+		irq_cfg = TQMX86_REG_IO_EXT_INT_NONE;
 		break;
 	case 7:
-		gpio_irq_cfg = TQMX86_REG_IO_EXT_INT_7;
+		irq_cfg = TQMX86_REG_IO_EXT_INT_7;
 		break;
 	case 9:
-		gpio_irq_cfg = TQMX86_REG_IO_EXT_INT_9;
+		irq_cfg = TQMX86_REG_IO_EXT_INT_9;
 		break;
 	case 12:
-		gpio_irq_cfg = TQMX86_REG_IO_EXT_INT_12;
+		irq_cfg = TQMX86_REG_IO_EXT_INT_12;
 		break;
 	default:
-		pr_err("tqmx86: Invalid GPIO IRQ (%d)\n", gpio_irq);
+		dev_err(dev, "invalid %s IRQ (%d)\n", label, irq);
 		return -EINVAL;
 	}
 
+	val = ioread8(io_base + TQMX86_REG_IO_EXT_INT);
+	val &= ~(TQMX86_REG_IO_EXT_INT_MASK << reg_shift);
+	val |= (irq_cfg & TQMX86_REG_IO_EXT_INT_MASK) << reg_shift;
+
+	iowrite8(val, io_base + TQMX86_REG_IO_EXT_INT);
+	readback = ioread8(io_base + TQMX86_REG_IO_EXT_INT);
+	if (readback != val) {
+		dev_warn(dev, "%s interrupts not supported\n", label);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int tqmx86_probe(struct platform_device *pdev)
+{
+	u8 board_id, sauc, rev, i2c_det;
+	struct device *dev = &pdev->dev;
+	const char *board_name;
+	void __iomem *io_base;
+	int err;
+
 	io_base = devm_ioport_map(dev, TQMX86_IOBASE, TQMX86_IOSIZE);
 	if (!io_base)
 		return -ENOMEM;
@@ -233,15 +252,11 @@ static int tqmx86_probe(struct platform_device *pdev)
 	 */
 	i2c_det = inb(TQMX86_REG_I2C_DETECT);
 
-	if (gpio_irq_cfg) {
-		io_ext_int_val =
-			gpio_irq_cfg << TQMX86_REG_IO_EXT_INT_GPIO_SHIFT;
-		iowrite8(io_ext_int_val, io_base + TQMX86_REG_IO_EXT_INT);
-		readback = ioread8(io_base + TQMX86_REG_IO_EXT_INT);
-		if (readback != io_ext_int_val) {
-			dev_warn(dev, "GPIO interrupts not supported.\n");
-			return -EINVAL;
-		}
+	if (gpio_irq) {
+		err = tqmx86_setup_irq(dev, "GPIO", gpio_irq, io_base,
+				       TQMX86_REG_IO_EXT_INT_GPIO_SHIFT);
+		if (err)
+			return err;
 
 		/* Assumes the IRQ resource is first. */
 		tqmx_gpio_resources[0].start = gpio_irq;
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/

[PATCH v6 4/5] mfd: tqmx86: make IRQ setup errors non-fatal

[Matthias Schiffer]

GPIO IRQ setup can fail either because an invalid IRQ was passed as a
parameter, or because the GPIO controller does not support interrupts.
Neither is severe enough to stop the whole probe; simply disable IRQ
support in the GPIO resource when setup fails.

The code is made a bit more robust by introduing a define for the index
of the IRQ resource in the resource list instead of assuming that it is
at index 0.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
---

v2: no changes (was patch 3/4)
v3: replace IRQ 0 resource with an empty placeholder to simplify error handling
v4: no changes
v5: move placeholder to the end of the resource array, use define for index
v6: no changes

 drivers/mfd/tqmx86.c | 19 +++++++------------
 1 file changed, 7 insertions(+), 12 deletions(-)

diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
index 8aa448a67c9a5..1fd2212bf492c 100644
--- a/drivers/mfd/tqmx86.c
+++ b/drivers/mfd/tqmx86.c
@@ -60,6 +60,9 @@ static uint gpio_irq;
 module_param(gpio_irq, uint, 0);
 MODULE_PARM_DESC(gpio_irq, "GPIO IRQ number (valid parameters: 7, 9, 12)");
 
+/* Index of IRQ placeholder in resource list */
+#define TQMX86_IRQ_GPIO 1
+
 static const struct resource tqmx_i2c_soft_resources[] = {
 	DEFINE_RES_IO(TQMX86_IOBASE_I2C, TQMX86_IOSIZE_I2C),
 };
@@ -68,13 +71,10 @@ static const struct resource tqmx_watchdog_resources[] = {
 	DEFINE_RES_IO(TQMX86_IOBASE_WATCHDOG, TQMX86_IOSIZE_WATCHDOG),
 };
 
-/*
- * The IRQ resource must be first, since it is updated with the
- * configured IRQ in the probe function.
- */
 static struct resource tqmx_gpio_resources[] = {
-	DEFINE_RES_IRQ(0),
 	DEFINE_RES_IO(TQMX86_IOBASE_GPIO, TQMX86_IOSIZE_GPIO),
+	/* Placeholder for IRQ resource - filled in by the probe function */
+	[TQMX86_IRQ_GPIO] = {},
 };
 
 static struct i2c_board_info tqmx86_i2c_devices[] = {
@@ -255,13 +255,8 @@ static int tqmx86_probe(struct platform_device *pdev)
 	if (gpio_irq) {
 		err = tqmx86_setup_irq(dev, "GPIO", gpio_irq, io_base,
 				       TQMX86_REG_IO_EXT_INT_GPIO_SHIFT);
-		if (err)
-			return err;
-
-		/* Assumes the IRQ resource is first. */
-		tqmx_gpio_resources[0].start = gpio_irq;
-	} else {
-		tqmx_gpio_resources[0].flags = 0;
+		if (!err)
+			tqmx_gpio_resources[TQMX86_IRQ_GPIO] = DEFINE_RES_IRQ(gpio_irq);
 	}
 
 	ocores_platform_data.clock_khz = tqmx86_board_id_to_clk_rate(dev, board_id);
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/

Re: [PATCH v6 4/5] mfd: tqmx86: make IRQ setup errors non-fatal

[Lee Jones]

On Mon, 04 Nov 2024, Matthias Schiffer wrote:

> GPIO IRQ setup can fail either because an invalid IRQ was passed as a
> parameter, or because the GPIO controller does not support interrupts.
> Neither is severe enough to stop the whole probe; simply disable IRQ
> support in the GPIO resource when setup fails.
> 
> The code is made a bit more robust by introduing a define for the index
> of the IRQ resource in the resource list instead of assuming that it is
> at index 0.
> 
> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
> ---
> 
> v2: no changes (was patch 3/4)
> v3: replace IRQ 0 resource with an empty placeholder to simplify error handling
> v4: no changes
> v5: move placeholder to the end of the resource array, use define for index
> v6: no changes
> 
>  drivers/mfd/tqmx86.c | 19 +++++++------------
>  1 file changed, 7 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
> index 8aa448a67c9a5..1fd2212bf492c 100644
> --- a/drivers/mfd/tqmx86.c
> +++ b/drivers/mfd/tqmx86.c
> @@ -60,6 +60,9 @@ static uint gpio_irq;
>  module_param(gpio_irq, uint, 0);
>  MODULE_PARM_DESC(gpio_irq, "GPIO IRQ number (valid parameters: 7, 9, 12)");
>  
> +/* Index of IRQ placeholder in resource list */
> +#define TQMX86_IRQ_GPIO 1
> +
>  static const struct resource tqmx_i2c_soft_resources[] = {
>  	DEFINE_RES_IO(TQMX86_IOBASE_I2C, TQMX86_IOSIZE_I2C),
>  };
> @@ -68,13 +71,10 @@ static const struct resource tqmx_watchdog_resources[] = {
>  	DEFINE_RES_IO(TQMX86_IOBASE_WATCHDOG, TQMX86_IOSIZE_WATCHDOG),
>  };
>  
> -/*
> - * The IRQ resource must be first, since it is updated with the
> - * configured IRQ in the probe function.
> - */
>  static struct resource tqmx_gpio_resources[] = {
> -	DEFINE_RES_IRQ(0),
>  	DEFINE_RES_IO(TQMX86_IOBASE_GPIO, TQMX86_IOSIZE_GPIO),
> +	/* Placeholder for IRQ resource - filled in by the probe function */

Drop the " - filled in ..." part.  This is a common practice.

> +	[TQMX86_IRQ_GPIO] = {},

Not quite.  What happens if someone comes along and inserts a resource
above this one?  You need to index all of them.  Use an enum.

>  };
>  
>  static struct i2c_board_info tqmx86_i2c_devices[] = {
> @@ -255,13 +255,8 @@ static int tqmx86_probe(struct platform_device *pdev)
>  	if (gpio_irq) {
>  		err = tqmx86_setup_irq(dev, "GPIO", gpio_irq, io_base,
>  				       TQMX86_REG_IO_EXT_INT_GPIO_SHIFT);
> -		if (err)
> -			return err;
> -
> -		/* Assumes the IRQ resource is first. */
> -		tqmx_gpio_resources[0].start = gpio_irq;
> -	} else {
> -		tqmx_gpio_resources[0].flags = 0;
> +		if (!err)
> +			tqmx_gpio_resources[TQMX86_IRQ_GPIO] = DEFINE_RES_IRQ(gpio_irq);

This section just became a lot nicer.

>  	}
>  
>  	ocores_platform_data.clock_khz = tqmx86_board_id_to_clk_rate(dev, board_id);
> -- 
> TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
> Amtsgericht München, HRB 105018
> Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
> https://www.tq-group.com/
> 

-- 
Lee Jones [李琼斯]

[PATCH v6 5/5] mfd: tqmx86: add I2C IRQ support

[Matthias Schiffer]

From: Gregor Herburger <gregor.herburger@tq-group.com>

The i2c-ocores controller can run in interrupt mode on tqmx86 modules.
Add module parameter to allow configuring the IRQ number, similar to the
handling of the GPIO IRQ.

The new code and module parameter refer to the I2C controller as "I2C1",
as the TQMx86 PLD actually contains a second I2C controller, for which
driver support will be added in the future.

Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
---

v2: improve module parameter description (was patch 4/4)
v3: replace IRQ 0 resource with an empty placeholder to simplify error handling
v4: no changes
v5: move placeholder to the end of the resource array, use define for index
v6:
  - remove obsolete comment
  - refer to I2C controller as "I2C1"

 drivers/mfd/tqmx86.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
index 1fd2212bf492c..7dd971b762578 100644
--- a/drivers/mfd/tqmx86.c
+++ b/drivers/mfd/tqmx86.c
@@ -50,6 +50,7 @@
 #define TQMX86_REG_IO_EXT_INT_9			2
 #define TQMX86_REG_IO_EXT_INT_12		3
 #define TQMX86_REG_IO_EXT_INT_MASK		0x3
+#define TQMX86_REG_IO_EXT_INT_I2C1_SHIFT	0
 #define TQMX86_REG_IO_EXT_INT_GPIO_SHIFT	4
 #define TQMX86_REG_SAUC		0x17
 
@@ -60,11 +61,18 @@ static uint gpio_irq;
 module_param(gpio_irq, uint, 0);
 MODULE_PARM_DESC(gpio_irq, "GPIO IRQ number (valid parameters: 7, 9, 12)");
 
+static uint i2c1_irq;
+module_param(i2c1_irq, uint, 0);
+MODULE_PARM_DESC(i2c1_irq, "I2C1 IRQ number (valid parameters: 7, 9, 12)");
+
 /* Index of IRQ placeholder in resource list */
 #define TQMX86_IRQ_GPIO 1
+#define TQMX86_IRQ_I2C1 1
 
-static const struct resource tqmx_i2c_soft_resources[] = {
+static struct resource tqmx_i2c_soft_resources[] = {
 	DEFINE_RES_IO(TQMX86_IOBASE_I2C, TQMX86_IOSIZE_I2C),
+	/* Placeholder for IRQ resource - filled in by the probe function */
+	[TQMX86_IRQ_I2C1] = {},
 };
 
 static const struct resource tqmx_watchdog_resources[] = {
@@ -262,6 +270,13 @@ static int tqmx86_probe(struct platform_device *pdev)
 	ocores_platform_data.clock_khz = tqmx86_board_id_to_clk_rate(dev, board_id);
 
 	if (i2c_det == TQMX86_REG_I2C_DETECT_SOFT) {
+		if (i2c1_irq) {
+			err = tqmx86_setup_irq(dev, "I2C1", i2c1_irq, io_base,
+					       TQMX86_REG_IO_EXT_INT_I2C1_SHIFT);
+			if (!err)
+				tqmx_i2c_soft_resources[TQMX86_IRQ_I2C1] = DEFINE_RES_IRQ(i2c1_irq);
+		}
+
 		err = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
 					   tqmx86_i2c_soft_dev,
 					   ARRAY_SIZE(tqmx86_i2c_soft_dev),
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/

Re: [PATCH v6 5/5] mfd: tqmx86: add I2C IRQ support

[Lee Jones]

On Mon, 04 Nov 2024, Matthias Schiffer wrote:

> From: Gregor Herburger <gregor.herburger@tq-group.com>
> 
> The i2c-ocores controller can run in interrupt mode on tqmx86 modules.
> Add module parameter to allow configuring the IRQ number, similar to the
> handling of the GPIO IRQ.
> 
> The new code and module parameter refer to the I2C controller as "I2C1",
> as the TQMx86 PLD actually contains a second I2C controller, for which
> driver support will be added in the future.
> 
> Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
> ---
> 
> v2: improve module parameter description (was patch 4/4)
> v3: replace IRQ 0 resource with an empty placeholder to simplify error handling
> v4: no changes
> v5: move placeholder to the end of the resource array, use define for index
> v6:
>   - remove obsolete comment
>   - refer to I2C controller as "I2C1"
> 
>  drivers/mfd/tqmx86.c | 17 ++++++++++++++++-
>  1 file changed, 16 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mfd/tqmx86.c b/drivers/mfd/tqmx86.c
> index 1fd2212bf492c..7dd971b762578 100644
> --- a/drivers/mfd/tqmx86.c
> +++ b/drivers/mfd/tqmx86.c
> @@ -50,6 +50,7 @@
>  #define TQMX86_REG_IO_EXT_INT_9			2
>  #define TQMX86_REG_IO_EXT_INT_12		3
>  #define TQMX86_REG_IO_EXT_INT_MASK		0x3
> +#define TQMX86_REG_IO_EXT_INT_I2C1_SHIFT	0
>  #define TQMX86_REG_IO_EXT_INT_GPIO_SHIFT	4
>  #define TQMX86_REG_SAUC		0x17
>  
> @@ -60,11 +61,18 @@ static uint gpio_irq;
>  module_param(gpio_irq, uint, 0);
>  MODULE_PARM_DESC(gpio_irq, "GPIO IRQ number (valid parameters: 7, 9, 12)");
>  
> +static uint i2c1_irq;
> +module_param(i2c1_irq, uint, 0);
> +MODULE_PARM_DESC(i2c1_irq, "I2C1 IRQ number (valid parameters: 7, 9, 12)");
> +
>  /* Index of IRQ placeholder in resource list */
>  #define TQMX86_IRQ_GPIO 1
> +#define TQMX86_IRQ_I2C1 1
>  
> -static const struct resource tqmx_i2c_soft_resources[] = {
> +static struct resource tqmx_i2c_soft_resources[] = {
>  	DEFINE_RES_IO(TQMX86_IOBASE_I2C, TQMX86_IOSIZE_I2C),

Same here.

> +	/* Placeholder for IRQ resource - filled in by the probe function */
> +	[TQMX86_IRQ_I2C1] = {},
>  };
>  
>  static const struct resource tqmx_watchdog_resources[] = {
> @@ -262,6 +270,13 @@ static int tqmx86_probe(struct platform_device *pdev)
>  	ocores_platform_data.clock_khz = tqmx86_board_id_to_clk_rate(dev, board_id);
>  
>  	if (i2c_det == TQMX86_REG_I2C_DETECT_SOFT) {
> +		if (i2c1_irq) {
> +			err = tqmx86_setup_irq(dev, "I2C1", i2c1_irq, io_base,
> +					       TQMX86_REG_IO_EXT_INT_I2C1_SHIFT);
> +			if (!err)
> +				tqmx_i2c_soft_resources[TQMX86_IRQ_I2C1] = DEFINE_RES_IRQ(i2c1_irq);
> +		}
> +
>  		err = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
>  					   tqmx86_i2c_soft_dev,
>  					   ARRAY_SIZE(tqmx86_i2c_soft_dev),
> -- 
> TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
> Amtsgericht München, HRB 105018
> Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
> https://www.tq-group.com/
> 

-- 
Lee Jones [李琼斯]