public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Xu Yang <xu.yang_2@nxp.com>, Peter Chen <peter.chen@kernel.com>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Sasha Levin <sashal@kernel.org>,
	peter.chen@kernel.org, linux-usb@vger.kernel.org
Subject: [PATCH AUTOSEL 5.15 1/5] usb: chipidea: udc: create bounce buffer for problem sglist entries if possible
Date: Wed,  4 Dec 2024 17:19:17 -0500	[thread overview]
Message-ID: <20241204221925.2248843-1-sashal@kernel.org> (raw)

From: Xu Yang <xu.yang_2@nxp.com>

[ Upstream commit edfcc455c85ccc5855f0c329ca5a2d85cc9fc6c6 ]

The chipidea controller doesn't fully support sglist, such as it can not
transfer data spanned more dTDs to form a bus packet, so it can only work
on very limited cases.

The limitations as below:
1. the end address of the first sg buffer must be 4KB aligned.
2. the start and end address of the middle sg buffer must be 4KB aligned.
3. the start address of the first sg buffer must be 4KB aligned.

However, not all the use cases violate these limitations. To make the
controller compatible with most of the cases, this will try to bounce the
problem sglist entries which can be found by sglist_get_invalid_entry().
Then a bounced line buffer (the size will roundup to page size) will be
allocated to replace the remaining problem sg entries. The data will be
copied between problem sg entries and bounce buffer according to the
transfer direction. The bounce buffer will be freed when the request
completed.

Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240923081203.2851768-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/chipidea/udc.c | 148 +++++++++++++++++++++++++++++++++++++
 drivers/usb/chipidea/udc.h |   2 +
 2 files changed, 150 insertions(+)

diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index 8b6745b7588c7..d3be658768a9a 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -10,6 +10,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/dmapool.h>
+#include <linux/dma-direct.h>
 #include <linux/err.h>
 #include <linux/irqreturn.h>
 #include <linux/kernel.h>
@@ -538,6 +539,126 @@ static int prepare_td_for_sg(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 	return ret;
 }
 
+/*
+ * Verify if the scatterlist is valid by iterating each sg entry.
+ * Return invalid sg entry index which is less than num_sgs.
+ */
+static int sglist_get_invalid_entry(struct device *dma_dev, u8 dir,
+			struct usb_request *req)
+{
+	int i;
+	struct scatterlist *s = req->sg;
+
+	if (req->num_sgs == 1)
+		return 1;
+
+	dir = dir ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+
+	for (i = 0; i < req->num_sgs; i++, s = sg_next(s)) {
+		/* Only small sg (generally last sg) may be bounced. If
+		 * that happens. we can't ensure the addr is page-aligned
+		 * after dma map.
+		 */
+		if (dma_kmalloc_needs_bounce(dma_dev, s->length, dir))
+			break;
+
+		/* Make sure each sg start address (except first sg) is
+		 * page-aligned and end address (except last sg) is also
+		 * page-aligned.
+		 */
+		if (i == 0) {
+			if (!IS_ALIGNED(s->offset + s->length,
+						CI_HDRC_PAGE_SIZE))
+				break;
+		} else {
+			if (s->offset)
+				break;
+			if (!sg_is_last(s) && !IS_ALIGNED(s->length,
+						CI_HDRC_PAGE_SIZE))
+				break;
+		}
+	}
+
+	return i;
+}
+
+static int sglist_do_bounce(struct ci_hw_req *hwreq, int index,
+			bool copy, unsigned int *bounced)
+{
+	void *buf;
+	int i, ret, nents, num_sgs;
+	unsigned int rest, rounded;
+	struct scatterlist *sg, *src, *dst;
+
+	nents = index + 1;
+	ret = sg_alloc_table(&hwreq->sgt, nents, GFP_KERNEL);
+	if (ret)
+		return ret;
+
+	sg = src = hwreq->req.sg;
+	num_sgs = hwreq->req.num_sgs;
+	rest = hwreq->req.length;
+	dst = hwreq->sgt.sgl;
+
+	for (i = 0; i < index; i++) {
+		memcpy(dst, src, sizeof(*src));
+		rest -= src->length;
+		src = sg_next(src);
+		dst = sg_next(dst);
+	}
+
+	/* create one bounce buffer */
+	rounded = round_up(rest, CI_HDRC_PAGE_SIZE);
+	buf = kmalloc(rounded, GFP_KERNEL);
+	if (!buf) {
+		sg_free_table(&hwreq->sgt);
+		return -ENOMEM;
+	}
+
+	sg_set_buf(dst, buf, rounded);
+
+	hwreq->req.sg = hwreq->sgt.sgl;
+	hwreq->req.num_sgs = nents;
+	hwreq->sgt.sgl = sg;
+	hwreq->sgt.nents = num_sgs;
+
+	if (copy)
+		sg_copy_to_buffer(src, num_sgs - index, buf, rest);
+
+	*bounced = rest;
+
+	return 0;
+}
+
+static void sglist_do_debounce(struct ci_hw_req *hwreq, bool copy)
+{
+	void *buf;
+	int i, nents, num_sgs;
+	struct scatterlist *sg, *src, *dst;
+
+	sg = hwreq->req.sg;
+	num_sgs = hwreq->req.num_sgs;
+	src = sg_last(sg, num_sgs);
+	buf = sg_virt(src);
+
+	if (copy) {
+		dst = hwreq->sgt.sgl;
+		for (i = 0; i < num_sgs - 1; i++)
+			dst = sg_next(dst);
+
+		nents = hwreq->sgt.nents - num_sgs + 1;
+		sg_copy_from_buffer(dst, nents, buf, sg_dma_len(src));
+	}
+
+	hwreq->req.sg = hwreq->sgt.sgl;
+	hwreq->req.num_sgs = hwreq->sgt.nents;
+	hwreq->sgt.sgl = sg;
+	hwreq->sgt.nents = num_sgs;
+
+	kfree(buf);
+	sg_free_table(&hwreq->sgt);
+}
+
 /**
  * _hardware_enqueue: configures a request at hardware level
  * @hwep:   endpoint
@@ -550,6 +671,8 @@ static int _hardware_enqueue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 	struct ci_hdrc *ci = hwep->ci;
 	int ret = 0;
 	struct td_node *firstnode, *lastnode;
+	unsigned int bounced_size;
+	struct scatterlist *sg;
 
 	/* don't queue twice */
 	if (hwreq->req.status == -EALREADY)
@@ -557,11 +680,29 @@ static int _hardware_enqueue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 
 	hwreq->req.status = -EALREADY;
 
+	if (hwreq->req.num_sgs && hwreq->req.length &&
+		ci->has_short_pkt_limit) {
+		ret = sglist_get_invalid_entry(ci->dev->parent, hwep->dir,
+					&hwreq->req);
+		if (ret < hwreq->req.num_sgs) {
+			ret = sglist_do_bounce(hwreq, ret, hwep->dir == TX,
+					&bounced_size);
+			if (ret)
+				return ret;
+		}
+	}
+
 	ret = usb_gadget_map_request_by_dev(ci->dev->parent,
 					    &hwreq->req, hwep->dir);
 	if (ret)
 		return ret;
 
+	if (hwreq->sgt.sgl) {
+		/* We've mapped a bigger buffer, now recover the actual size */
+		sg = sg_last(hwreq->req.sg, hwreq->req.num_sgs);
+		sg_dma_len(sg) = min(sg_dma_len(sg), bounced_size);
+	}
+
 	if (hwreq->req.num_mapped_sgs)
 		ret = prepare_td_for_sg(hwep, hwreq);
 	else
@@ -724,6 +865,10 @@ static int _hardware_dequeue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 	usb_gadget_unmap_request_by_dev(hwep->ci->dev->parent,
 					&hwreq->req, hwep->dir);
 
+	/* sglist bounced */
+	if (hwreq->sgt.sgl)
+		sglist_do_debounce(hwreq, hwep->dir == RX);
+
 	hwreq->req.actual += actual;
 
 	if (hwreq->req.status)
@@ -1565,6 +1710,9 @@ static int ep_dequeue(struct usb_ep *ep, struct usb_request *req)
 
 	usb_gadget_unmap_request(&hwep->ci->gadget, req, hwep->dir);
 
+	if (hwreq->sgt.sgl)
+		sglist_do_debounce(hwreq, false);
+
 	req->status = -ECONNRESET;
 
 	if (hwreq->req.complete != NULL) {
diff --git a/drivers/usb/chipidea/udc.h b/drivers/usb/chipidea/udc.h
index 5193df1e18c75..c8a47389a46bb 100644
--- a/drivers/usb/chipidea/udc.h
+++ b/drivers/usb/chipidea/udc.h
@@ -69,11 +69,13 @@ struct td_node {
  * @req: request structure for gadget drivers
  * @queue: link to QH list
  * @tds: link to TD list
+ * @sgt: hold original sglist when bounce sglist
  */
 struct ci_hw_req {
 	struct usb_request	req;
 	struct list_head	queue;
 	struct list_head	tds;
+	struct sg_table		sgt;
 };
 
 #ifdef CONFIG_USB_CHIPIDEA_UDC
-- 
2.43.0


             reply	other threads:[~2024-12-04 23:30 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-12-04 22:19 Sasha Levin [this message]
2024-12-04 22:19 ` [PATCH AUTOSEL 5.15 2/5] usb: chipidea: udc: handle USB Error Interrupt if IOC not set Sasha Levin
2024-12-04 22:19 ` [PATCH AUTOSEL 5.15 3/5] phy: tegra: xusb: Set fwnode for xusb port devices Sasha Levin
2024-12-06  0:04   ` Saravana Kannan
2024-12-04 22:19 ` [PATCH AUTOSEL 5.15 4/5] MIPS: Loongson64: DTS: Really fix PCIe port nodes for ls7a Sasha Levin
2024-12-04 22:19 ` [PATCH AUTOSEL 5.15 5/5] powerpc/prom_init: Fixup missing powermac #size-cells Sasha Levin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20241204221925.2248843-1-sashal@kernel.org \
    --to=sashal@kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=peter.chen@kernel.com \
    --cc=peter.chen@kernel.org \
    --cc=stable@vger.kernel.org \
    --cc=xu.yang_2@nxp.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox