[PATCH] ata: sata_gemini: Remove remaining reset glue

[linux@treblig.org]

From: "Dr. David Alan Gilbert" <linux@treblig.org>

Now that gemini_sata_reset_bridge() is gone, we can remove
the sata0/1_reset members and the code that creates them.

Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
---

Note: Applies after my
  ata: sata_gemini: Remove unused gemini_sata_reset_bridge()

 drivers/ata/sata_gemini.c | 20 --------------------
 1 file changed, 20 deletions(-)

diff --git a/drivers/ata/sata_gemini.c b/drivers/ata/sata_gemini.c
index 821ca31effe7..530ee26b3012 100644
--- a/drivers/ata/sata_gemini.c
+++ b/drivers/ata/sata_gemini.c
@@ -11,7 +11,6 @@
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
 #include <linux/delay.h>
-#include <linux/reset.h>
 #include <linux/of.h>
 #include <linux/clk.h>
 #include <linux/io.h>
@@ -27,8 +26,6 @@
  * @muxmode: the current muxing mode
  * @ide_pins: if the device is using the plain IDE interface pins
  * @sata_bridge: if the device enables the SATA bridge
- * @sata0_reset: SATA0 reset handler
- * @sata1_reset: SATA1 reset handler
  * @sata0_pclk: SATA0 PCLK handler
  * @sata1_pclk: SATA1 PCLK handler
  */
@@ -38,8 +35,6 @@ struct sata_gemini {
 	enum gemini_muxmode muxmode;
 	bool ide_pins;
 	bool sata_bridge;
-	struct reset_control *sata0_reset;
-	struct reset_control *sata1_reset;
 	struct clk *sata0_pclk;
 	struct clk *sata1_pclk;
 };
@@ -253,21 +248,6 @@ static int gemini_sata_bridge_init(struct sata_gemini *sg)
 		return ret;
 	}
 
-	sg->sata0_reset = devm_reset_control_get_exclusive(dev, "sata0");
-	if (IS_ERR(sg->sata0_reset)) {
-		dev_err(dev, "no SATA0 reset controller\n");
-		clk_disable_unprepare(sg->sata1_pclk);
-		clk_disable_unprepare(sg->sata0_pclk);
-		return PTR_ERR(sg->sata0_reset);
-	}
-	sg->sata1_reset = devm_reset_control_get_exclusive(dev, "sata1");
-	if (IS_ERR(sg->sata1_reset)) {
-		dev_err(dev, "no SATA1 reset controller\n");
-		clk_disable_unprepare(sg->sata1_pclk);
-		clk_disable_unprepare(sg->sata0_pclk);
-		return PTR_ERR(sg->sata1_reset);
-	}
-
 	sata_id = readl(sg->base + GEMINI_SATA_ID);
 	sata_phy_id = readl(sg->base + GEMINI_SATA_PHY_ID);
 	sg->sata_bridge = true;
-- 
2.47.1