[PATCH] arm64: dts: rockchip: Improve LED config for NanoPi R5S

[Diederik de Haas <didi.debian@cknow.org>]

The NanoPi R5S has 4 GPIO LEDs, a RED one for SYStem power and 3 green
LEDs meant to indicate that a cable is connected to either of the
2.5GbE LAN ports or the 1GbE WAN port.

In the NanoPi R5S schematic (2204; page 19) as well as on the PCB and on
the case, SYS is used and not POWER. So replace 'power' with 'sys'.
But keep the 'power_led' label/phandle even though the kernel doesn't
use it, but it may be used outside of it.

The SYStem LED already had "heartbeat" as its default-trigger.
Set the default-trigger to "netdev" for the NICs so they will show when
LAN1/LAN2/WAN is connected and set their default-state to "off".

Also assign labels as close as possible to the labels on the case, while
still being descriptive enough in their own right.

Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
---
 .../boot/dts/rockchip/rk3568-nanopi-r5s.dts    | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts
index 4cb8df1129c0..3b31f0dd8f3b 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts
@@ -20,33 +20,43 @@ aliases {
 	gpio-leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&lan1_led_pin>, <&lan2_led_pin>, <&power_led_pin>, <&wan_led_pin>;
+		pinctrl-0 = <&lan1_led_pin>, <&lan2_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
 
 		led-lan1 {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_LAN;
 			function-enumerator = <1>;
 			gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>;
+			label = "LAN-1";
+			linux,default-trigger = "netdev";
 		};
 
 		led-lan2 {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_LAN;
 			function-enumerator = <2>;
 			gpios = <&gpio3 RK_PD7 GPIO_ACTIVE_HIGH>;
+			label = "LAN-2";
+			linux,default-trigger = "netdev";
 		};
 
-		power_led: led-power {
+		power_led: led-sys {
 			color = <LED_COLOR_ID_RED>;
 			function = LED_FUNCTION_POWER;
-			linux,default-trigger = "heartbeat";
 			gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+			label = "SYS";
+			linux,default-trigger = "heartbeat";
 		};
 
 		led-wan {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_WAN;
 			gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+			label = "WAN";
+			linux,default-trigger = "netdev";
 		};
 	};
 };
@@ -126,7 +136,7 @@ lan2_led_pin: lan2-led-pin {
 			rockchip,pins = <3 RK_PD7 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		power_led_pin: power-led-pin {
+		sys_led_pin: sys-led-pin {
 			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-- 
2.49.0