[PATCH v5 0/4] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[PATCH v5 0/4] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[Jens Glathe via B4 Relay]

Device tree for the Lenovo Thinkbook 16 G7 QOY

The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].

Supported features:

- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera

Not supported yet:

- HDMI port.
- EC and some fn hotkeys.

Limited support yet:

- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.

- The GPU is not yet supported. Graphics is only software rendered. However, the 
node is defined and active since the available of the X1-45 support is soon-ish
and the Laptop boots with it enabled, too.

Notes:

- Putting the camera behind usb_2_dwc3 results in the camera switched of after 30 
seconds. With the stand-alone node as previously defined it stays usable and 
suspends, as intended. Sincethe sole reason for the USB camera to be in the 
devicetree is the required extra supply (which is guessed, as mentioned), and
its handling by power management, I would propose to keep it this way.

- The gpi_dma nodes appear to be implicitly enabled when a serial device is used.
I added them, no change in behaviour, though. Since this would be the only X1 
device adding them afaik, I left them out.

- The cma-memory is removed, it is not on all x1 devices as I assumed. 
Haven't found a case where it is required.

- i2c2 defines the keyboard and 4 different touchpad interfaces. With the bundling
of the pinctrl it seems to work better. I've had issues with only clock and touchpad
pinctrl on the i2c2 node, and not keyboard.

This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1 device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).

I have brought up the Thinkbook over the last 4 months since the x1p42100-crd
patches were available. The laptop is very usable now, and quite solid as a dev/
test platform. GPU support would be nice, though :)

Big thanks to Aleksandrs Vinarskis for helping (and sort of persisting) on the
fingerprint, camera and HDMI issues.

[1]: https://psref.lenovo.com/syspool/Sys/PDF/ThinkBook/ThinkBook_16_G7_QOY/ThinkBook_16_G7_QOY_Spec.pdf

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
Changes in v5:
- removed patch for the CMN N160JCE-ELL panel, got reviewed
- re-ordered code in onboard_usb_dev as requested by Dmitry Baryshkov
- amended device tree with review notes from Dmitry Baryshkov where possible
  and resuting in a working laptop - added notes section
- Link to v4: https://lore.kernel.org/r/20250524-tb16-dt-v4-0-2c1e6018d3f0@oldschoolsolutions.biz

Changes in v4:
- squashed Makefile and dts commits to one
- picked up r-b from Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
- Link to v3: https://lore.kernel.org/r/20250524-tb16-dt-v3-0-17e26d935e73@oldschoolsolutions.biz

Changes in v3:
- removed changes in x1e80100.dtsi and x1p42100.dtsi - resolved with [2]
- fixed schema errors with correct compatible string for the model
- added power management for the camera via onboard_usb_dev.c
- amended node ordering
- changed the panel driver used to edp-panel, added panel in the driver
- amended x1e80100.dtsi for exposing PM8010: This one is not present in the design, 
  added /delete-node/ for it.
- removed commented-out lines for sdhc, specified which don't work.
- corrected ZAP shader firmware name
- Link to v2: https://lore.kernel.org/r/20250516-tb16-dt-v2-0-7c4996d58ed6@oldschoolsolutions.biz

Changes in v2:
- removed nodes that gave DTC compile errors (pm8010_thermal, edp0_hpd_active)
- amended qcom.yaml
- shortened the commit titles to fit 75 chars
- Link to v1: https://lore.kernel.org/r/20250515-tb16-dt-v1-0-dc5846a25c48@oldschoolsolutions.biz

[2]: 20250520-topic-x1p4_tsens-v2-1-9687b789a4fb@oss.qualcomm.com

---
Jens Glathe (4):
      dt-bindings: arm: qcom: Add Lenovo TB16 support
      usb: misc: onboard_usb_dev: Add Bison Electronics Inc. Integrated Camera
      firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16
      arm64: dts: qcom: Add Lenovo ThinkBook 16 G7 QOY device tree

 Documentation/devicetree/bindings/arm/qcom.yaml    |    1 +
 arch/arm64/boot/dts/qcom/Makefile                  |    2 +
 arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi       |    2 +-
 .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1648 ++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |    1 +
 drivers/usb/misc/onboard_usb_dev.c                 |    2 +
 drivers/usb/misc/onboard_usb_dev.h                 |    8 +
 7 files changed, 1663 insertions(+), 1 deletion(-)
---
base-commit: 475c850a7fdd0915b856173186d5922899d65686
change-id: 20250511-tb16-dt-e84c433d87b1

Best regards,
-- 
Jens Glathe <jens.glathe@oldschoolsolutions.biz>

[PATCH v5 1/4] dt-bindings: arm: qcom: Add Lenovo TB16 support

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Document the x1p-42-100/x1-26-100 variants of the Thinkbook 16 G7 QOY.

[1]: https://psref.lenovo.com/syspool/Sys/PDF/ThinkBook/ThinkBook_16_G7_QOY/ThinkBook_16_G7_QOY_Spec.pdf

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 56f78f0f3803fedcb6422efd6adec3bbc81c2e03..5654aaf825955f8000355600c0ae35b74676273e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1153,6 +1153,7 @@ properties:
       - items:
           - enum:
               - asus,zenbook-a14-ux3407qa
+              - lenovo,thinkbook-16
               - qcom,x1p42100-crd
           - const: qcom,x1p42100
 

-- 
2.48.1

[PATCH v5 2/4] usb: misc: onboard_usb_dev: Add Bison Electronics Inc. Integrated Camera

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

The Camera is built into the Thinkbook 16 G7 QOY and directly attached on the
usb_2 controller (dwc3 USB2 only). It has a separate power supply that needs
to be controlled for PM.

Add the support for this device for the power supply.

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/usb/misc/onboard_usb_dev.c | 2 ++
 drivers/usb/misc/onboard_usb_dev.h | 8 ++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/usb/misc/onboard_usb_dev.c b/drivers/usb/misc/onboard_usb_dev.c
index 5b481876af1b2c10ce625fcf0fb8bfbe8905aa8c..41360a7591e56b2b1fe973ff1c42e68707fff54d 100644
--- a/drivers/usb/misc/onboard_usb_dev.c
+++ b/drivers/usb/misc/onboard_usb_dev.c
@@ -564,6 +564,7 @@ static struct platform_driver onboard_dev_driver = {
 
 /************************** USB driver **************************/
 
+#define VENDOR_ID_BISON		0x5986
 #define VENDOR_ID_CYPRESS	0x04b4
 #define VENDOR_ID_GENESYS	0x05e3
 #define VENDOR_ID_MICROCHIP	0x0424
@@ -647,6 +648,7 @@ static void onboard_dev_usbdev_disconnect(struct usb_device *udev)
 }
 
 static const struct usb_device_id onboard_dev_id_table[] = {
+	{ USB_DEVICE(VENDOR_ID_BISON, 0x1198) }, /* Bison Electronics Inc. Integrated Camera */
 	{ USB_DEVICE(VENDOR_ID_CYPRESS, 0x6500) }, /* CYUSB330x 3.0 HUB */
 	{ USB_DEVICE(VENDOR_ID_CYPRESS, 0x6502) }, /* CYUSB330x 2.0 HUB */
 	{ USB_DEVICE(VENDOR_ID_CYPRESS, 0x6503) }, /* CYUSB33{0,1}x 2.0 HUB, Vendor Mode */
diff --git a/drivers/usb/misc/onboard_usb_dev.h b/drivers/usb/misc/onboard_usb_dev.h
index e017b8e22f936be66da73789abb4f620e6af4d6a..b95ac757868e7cd3f23eb4b80eb595a2c18e9613 100644
--- a/drivers/usb/misc/onboard_usb_dev.h
+++ b/drivers/usb/misc/onboard_usb_dev.h
@@ -73,6 +73,13 @@ static const struct onboard_dev_pdata ti_tusb8041_data = {
 	.is_hub = true,
 };
 
+static const struct onboard_dev_pdata bison_intcamera_data = {
+	.reset_us = 1000,
+	.num_supplies = 1,
+	.supply_names = { "vdd" },
+	.is_hub = false,
+};
+
 static const struct onboard_dev_pdata cypress_hx3_data = {
 	.reset_us = 10000,
 	.num_supplies = 2,
@@ -127,6 +134,7 @@ static const struct of_device_id onboard_dev_match[] = {
 	{ .compatible = "usb451,8142", .data = &ti_tusb8041_data, },
 	{ .compatible = "usb451,8440", .data = &ti_tusb8041_data, },
 	{ .compatible = "usb451,8442", .data = &ti_tusb8041_data, },
+	{ .compatible = "usb5986,1198", .data = &bison_intcamera_data, },
 	{ .compatible = "usb4b4,6504", .data = &cypress_hx3_data, },
 	{ .compatible = "usb4b4,6506", .data = &cypress_hx3_data, },
 	{ .compatible = "usb4b4,6570", .data = &cypress_hx2vl_data, },

-- 
2.48.1

[PATCH v5 3/4] firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Allow particular machine accessing eg. efivars.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/firmware/qcom/qcom_scm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index f63b716be5b027550ae3a987e784f0814ea6d678..171cc2a6502463e3445919ef77a129563ea233a4 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1993,6 +1993,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "hp,omnibook-x14" },
 	{ .compatible = "huawei,gaokun3" },
 	{ .compatible = "lenovo,flex-5g" },
+	{ .compatible = "lenovo,thinkbook-16" },
 	{ .compatible = "lenovo,thinkpad-t14s" },
 	{ .compatible = "lenovo,thinkpad-x13s", },
 	{ .compatible = "lenovo,yoga-slim7x" },

-- 
2.48.1

[PATCH v5 4/4] arm64: dts: qcom: Add Lenovo ThinkBook 16 G7 QOY device tree

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Device tree for the Lenovo Thinkbook 16 G7 QOY

The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].

Supported features:

- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera

Not supported yet:

- HDMI port.
- EC and some fn hotkeys.

Limited support yet:

- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.

- The GPU is not yet supported. Graphics is only software rendered.

This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1e device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Co-developed by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |    2 +
 arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi       |    2 +-
 .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1648 ++++++++++++++++++++
 3 files changed, 1651 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 669b888b27a1daa93ac15f47e8b9a302bb0922c2..c383d887b0359c85aa3638e95e317a66ef1399c2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -327,3 +327,5 @@ x1e80100-qcp-el2-dtbs	:= x1e80100-qcp.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-qcp.dtb x1e80100-qcp-el2.dtb
 x1p42100-crd-el2-dtbs	:= x1p42100-crd.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-crd.dtb x1p42100-crd-el2.dtb
+x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
index c02fd4d15c9649c222caaafa5ed2c777a10fb4f5..551b392eca4ef3b6041e03ad1385fef11cec1690 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
@@ -170,7 +170,7 @@ trip1 {
 			};
 		};
 
-		pm8010-thermal {
+		pm8010_thermal: pm8010-thermal {
 			polling-delay-passive = <100>;
 
 			thermal-sensors = <&pm8010_temp_alarm>;
diff --git a/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
new file mode 100644
index 0000000000000000000000000000000000000000..6e7263754a932b8fe22d73744691c6608b27a712
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
@@ -0,0 +1,1648 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2024, Linaro Limited
+ * Copyright (c) 2025, Jens Glathe
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1p42100.dtsi"
+#include "x1e80100-pmics.dtsi"
+
+/delete-node/ &pmc8380_6;
+/delete-node/ &pmc8380_6_thermal;
+/delete-node/ &pm8010;
+/delete-node/ &pm8010_thermal;
+
+/ {
+	model = "Lenovo ThinkBook 16 Gen 7 QOY";
+	compatible = "lenovo,thinkbook-16", "qcom,x1p42100";
+	chassis-type = "laptop";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wcd_default>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pm8550_pwm 3 500000>;
+
+		power-supply = <&vreg_edp_bl>;
+	};
+
+	/*
+	 * This is an odd one. The camera is physically behind the eusb9 repeater (confirmed) but
+	 * if it is placed below the usb_2_dwc3 node, it will be switched of after ~30 seconds.
+	 * The whole reason it is described in the dt (as an USB device) is its requirement for
+	 * that additional regulator, and to get power management to switch it off when suspended.
+	 * Defining it stand-alone does work.
+	 */
+	camera {
+		compatible = "usb5986,1198";
+
+		vdd-supply = <&vreg_cam_5p0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>;
+
+		/* Display-adjacent port */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "host";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss0_sbu_mux>;
+					};
+				};
+			};
+		};
+
+		/* User-adjacent port */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "host";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss1_sbu_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E80100-LENOVO-ThinkBook-16";
+		audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS3",
+				"VA DMIC1", "MIC BIAS3",
+				"VA DMIC2", "MIC BIAS1",
+				"VA DMIC3", "MIC BIAS1",
+				"VA DMIC0", "VA MIC BIAS3",
+				"VA DMIC1", "VA MIC BIAS3",
+				"VA DMIC2", "VA MIC BIAS1",
+				"VA DMIC3", "VA MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	usb-1-ss0-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss0_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss0_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss0_sbu>;
+			};
+		};
+	};
+
+	usb-1-ss1-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 178 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss1_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss1_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss1_sbu>;
+			};
+		};
+	};
+
+	vreg_cam_5p0: regulator-cam-5p0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_CAM_5P0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VBL9";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&misc_3p3_reg_en>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_en>;
+		pinctrl-1 = <&wcn_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p0: ldo5 {
+			regulator-name = "vreg_l5b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l16b_2p9: ldo16 {
+			regulator-name = "vreg_l16b_2p9";
+			regulator-min-microvolt = <2912000>;
+			regulator-max-microvolt = <2912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_1p0: ldo1 {
+			regulator-name = "vreg_l1f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_1p0: ldo2 {
+			regulator-name = "vreg_l2f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_1p0: ldo3 {
+			regulator-name = "vreg_l3f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+	zap-shader {
+		firmware-name = "qcom/x1e80100/LENOVO/21NH/qcdxkmsucpurwa.mbn";
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	pinctrl-0 = <&qup_i2c2_data_clk>, <&tpad_default>, <&kybd_default>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* ELAN06FA */
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* CIRQ1080 or SYNA2BA6 */
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* FTCS0038 */
+	touchpad@38 {
+		compatible = "hid-over-i2c";
+		reg = <0x38>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* GXTP5100 */
+	touchpad@5d {
+		compatible = "hid-over-i2c";
+		reg = <0x5d>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb5_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+	};
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb9_repeater: redriver@4b {
+		compatible = "nxp,ptn3222";
+		reg = <0x4b>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb9_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* ILIT2911 or GTCH1563 */
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l15b_1p8>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+
+			backlight = <&backlight>;
+
+			enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp3_out: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_pwm {
+	status = "okay";
+};
+
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-disable;
+		output-enable;
+		drive-push-pull;
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&pmc8380_3_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		input-disable;
+		output-enable;
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio10";
+		function = "normal";
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/LENOVO/21NH/qcadsp8380.mbn",
+			"qcom/x1e80100/LENOVO/21NH/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/LENOVO/21NH/qccdsp8380.mbn",
+			"qcom/x1e80100/LENOVO/21NH/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l6b_1p8>;
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Speaker */
+	left_spkr: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Speaker */
+	right_spkr: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <34 2>, /* Unused */
+		<72 2>, /* Secure EC I2C connection (?) */
+		<238 1>; /* UFS Reset */
+
+	cam_reg_en: cam-reg-en-state {
+		pins = "gpio44";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb9_reset_n: eusb9-reset-n-state {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_card_det_n: sdc2-card-det-state {
+		pins = "gpio71";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts0_default: ts0-default-state {
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n-pins {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+
+	usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
+		mode-pins {
+			pins = "gpio166";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+			output-high;
+		};
+
+		oe-n-pins {
+			pins = "gpio168";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio167";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+	};
+
+	usb_1_ss1_sbu_default: usb-1-ss1-sbu-state {
+		mode-pins {
+			pins = "gpio177";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+			output-high;
+		};
+
+		oe-n-pins {
+			pins = "gpio179";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio178";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_bt_en: wcn-bt-en-state {
+		pins = "gpio116";
+		function = "gpio";
+		drive-strength = <16>;
+		output-low;
+		bias-pull-down;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	wcn_wlan_en: wcn-wlan-en-state {
+		pins = "gpio117";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p8>;
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_1_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss1_ss_in>;
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	phys = <&usb_1_ss2_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&eusb5_repeater>;
+
+	status = "okay";
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb9_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};

-- 
2.48.1