* [PATCH v5 0/4] X1E Asus Zenbook A14 support
@ 2025-06-07 20:00 Aleksandrs Vinarskis
2025-06-07 20:00 ` [PATCH v5 4/4] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14 Aleksandrs Vinarskis
2025-06-09 15:01 ` [PATCH v5 0/4] X1E Asus Zenbook A14 support Rob Herring (Arm)
0 siblings, 2 replies; 4+ messages in thread
From: Aleksandrs Vinarskis @ 2025-06-07 20:00 UTC (permalink / raw)
To: Bjorn Andersson, Nikita Travkin, Konrad Dybcio,
Aleksandrs Vinarskis, linux-arm-msm, devicetree, linux-kernel
Cc: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
dmitry.baryshkov, maud_spierings
As requested, 1/4 was merged to linux-next by USB maintainers.
Resending 4/4 rebased on top of latest linux-next. 2/4, 3/4 already
landed.
With this in mind, and taking into account that this patch was
already reviewed some time ago, any possibility to still add 4/4 to
6.16?
---
Introduce support for the mentioned laptop.
Particular device exists in two model numbers:
* UX3407QA: X1P-42-100 or X1-26-100 (as tested)
* UX3407RA: X1E-78-100
Mostly similar to other X1-based laptops. Notable differences are:
* Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
and Qualcomm FastConnect 7800 on UX3407RA
* USB Type-C retimers are Parade PS8833, appear to behave identical
to Parade PS8830
* gpio90 is TZ protected
When comparing device firmware between UX3407QA, UX3407RA, it seems
that only ADSP firmware is different, CDSP and GPU firmware appears to
be the same. (At least assuming the GPU firmware name in both cases is
`qcdxkmsuc8380.mbn`). Since at least some blobs are different betweeen
X1E and X1/X1P, define new firmware directory for `qcom/x1p42100`. This
also makes it easier for distros to automatically extract firmware from
Windows and place all blobs for the model under the same path. If/When
firmware blobs make it to linux-firmware, same blobs can be easily
symlinked between `qcom/x1e80100` and `qcom/x1p42100`.
NVMe SSD depends on [1]. USB Type-A over USB MP controller depends on
[2], or equivalent proposed solution.
Qualcomm FastConnect 6900 on UX3407QA did not work out of the box, and
additionally required both newer firmware and patches to `board-2.bin`.
I added a short how-to [3], as it is not exactly trivial.
ACPI dumps can be found on aarch64-laptops' github [4]. HWids on
dtbloader's github [5].
[1] https://lore.kernel.org/linux-arm-msm/20250319094544.3980357-1-quic_wenbyao@quicinc.com/
[2] https://lore.kernel.org/all/20250318-xps13-fingerprint-v1-1-fbb02d5a34a7@oss.qualcomm.com/
[3] https://github.com/alexVinarskis/linux-x1e80100-zenbook-a14?tab=readme-ov-file#wcn688x-wifi
[4] https://github.com/aarch64-laptops/build/pull/134/files
[5] https://github.com/TravMurav/dtbloader/pull/4/files
[6] https://lore.kernel.org/all/20250429-x1e80100-dts-drop-useless-dp-compatible-override-v1-0-058847814d70@linaro.org/
[7] https://lore.kernel.org/all/20250524-tb16-dt-v4-5-2c1e6018d3f0@oldschoolsolutions.biz/
Changes to v5:
* _Only sending 4/4 as other patches are already applied_
* Rebase 4/4 on `next-20250606`
* Moved gpu enable from dtsi to respective dts as per discussion in [7]
Link to v5: https://lore.kernel.org/all/20250523131605.6624-1-alex.vinarskis@gmail.com/
Changes to v4:
* _Only sending 4/4 as other patches are already applied_
* Rebase 4/4 on `for-next` of qcom tree, adjust makefile to generate el2 dtbs
* Picked Konrad's R-by for 4/4
* Droped 'qcom,x1e80100-dp' as per [6]
Link to v4: https://lore.kernel.org/all/20250426130203.37659-1-alex.vinarskis@gmail.com/
Changes to v3:
* Drop redundant comments
* Drop incomplete wcn7850 as it is causing dt errors
* Picked a-by
Link to v3: https://lore.kernel.org/all/20250416232345.5240-1-alex.vinarskis@gmail.com/
Changes to v2:
* Fix/re-add PS8833 as fallback
* Add EC's i2c address
* Add pwrseq for wcn6855, placeholder for wcn7850 until its tested
* Rename x1-zenbook.dtsi to x1-asus-zenbook.dtsi
Link to v2: https://lore.kernel.org/all/20250402084646.10098-1-alex.vinarskis@gmail.com/
Changes to v1:
* Drop PS8833 variant, fallback to PS8830 as they behave the same
* Drop wrong pcie6a_phy compatible revert
* Drop redundant comments, fix order of properties in the device-tree
* Fix device name bindings, express in model names instead of the soc
* Fix GPU firmware name for UX3407QA
* Fix model string, enclose variant in parenthesis
* Added missing new lines before 'status = "okay";'
* Updated cover letter to reflect some of the above changes
* Left SPI10 disabled as it is unknown how/what for to use it as of now
Link to v1: https://lore.kernel.org/all/20250331215720.19692-1-alex.vinarskis@gmail.com/
Aleksandrs Vinarskis (1):
arm64: dts: qcom: Add support for X1-based Asus Zenbook A14
arch/arm64/boot/dts/qcom/Makefile | 4 +
.../boot/dts/qcom/x1-asus-zenbook-a14.dtsi | 1302 +++++++++++++++++
.../dts/qcom/x1e80100-asus-zenbook-a14.dts | 37 +
.../dts/qcom/x1p42100-asus-zenbook-a14.dts | 141 ++
4 files changed, 1484 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/x1-asus-zenbook-a14.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
create mode 100644 arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
--
2.45.2
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v5 4/4] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14
2025-06-07 20:00 [PATCH v5 0/4] X1E Asus Zenbook A14 support Aleksandrs Vinarskis
@ 2025-06-07 20:00 ` Aleksandrs Vinarskis
2025-06-10 11:58 ` Konrad Dybcio
2025-06-09 15:01 ` [PATCH v5 0/4] X1E Asus Zenbook A14 support Rob Herring (Arm)
1 sibling, 1 reply; 4+ messages in thread
From: Aleksandrs Vinarskis @ 2025-06-07 20:00 UTC (permalink / raw)
To: Bjorn Andersson, Nikita Travkin, Konrad Dybcio,
Aleksandrs Vinarskis, linux-arm-msm, devicetree, linux-kernel
Cc: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
dmitry.baryshkov, maud_spierings
Initial support for Asus Zenbook A14. Particular moddel exists
in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).
Mostly similar to other X1-based laptops. Notable differences are:
* Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
and Qualcomm FastConnect 7800 on UX3407RA
* USB Type-C retimers are Parade PS8833, appear to behave identical
to Parade PS8830
* gpio90 is TZ protected
Working:
* Keyboard
* Touchpad
* NVME
* Lid switch
* Camera LED
* eDP (FHD OLED, SDC420D) with brightness control
* Bluetooth, WiFi (WCN6855)
* USB Type-A port
* USB Type-C ports in USB2/USB3/DP (both orientations)
* aDSP/cDPS firmware loading, battery info
* Sleep/suspend, nothing visibly broken on resume
Out of scope of this series:
* Audio (Speakers/microphones/headphone jack)
* Camera (OmniVision OV02C10)
* HDMI (Parade PS185HDM)
* EC
Add dtsi and create two configurations for UX3407QA, UX3407RA.
Tested on UX3407QA with X1-26-100.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 4 +
.../boot/dts/qcom/x1-asus-zenbook-a14.dtsi | 1302 +++++++++++++++++
.../dts/qcom/x1e80100-asus-zenbook-a14.dts | 37 +
.../dts/qcom/x1p42100-asus-zenbook-a14.dts | 141 ++
4 files changed, 1484 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/x1-asus-zenbook-a14.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
create mode 100644 arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 669b888b27a1..06aca925e528 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -309,6 +309,8 @@ x1e78100-lenovo-thinkpad-t14s-oled-el2-dtbs := x1e78100-lenovo-thinkpad-t14s-ole
dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s-oled.dtb x1e78100-lenovo-thinkpad-t14s-oled-el2.dtb
x1e80100-asus-vivobook-s15-el2-dtbs := x1e80100-asus-vivobook-s15.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb x1e80100-asus-vivobook-s15-el2.dtb
+x1e80100-asus-zenbook-a14-el2-dtbs := x1e80100-asus-zenbook-a14.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-zenbook-a14.dtb x1e80100-asus-zenbook-a14-el2.dtb
x1e80100-crd-el2-dtbs := x1e80100-crd.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb x1e80100-crd-el2.dtb
x1e80100-dell-xps13-9345-el2-dtbs := x1e80100-dell-xps13-9345.dtb x1-el2.dtbo
@@ -325,5 +327,7 @@ x1e80100-microsoft-romulus15-el2-dtbs := x1e80100-microsoft-romulus15.dtb x1-el2
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtb x1e80100-microsoft-romulus15-el2.dtb
x1e80100-qcp-el2-dtbs := x1e80100-qcp.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-qcp.dtb x1e80100-qcp-el2.dtb
+x1p42100-asus-zenbook-a14-el2-dtbs := x1p42100-asus-zenbook-a14.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += x1p42100-asus-zenbook-a14.dtb x1p42100-asus-zenbook-a14-el2.dtb
x1p42100-crd-el2-dtbs := x1p42100-crd.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1p42100-crd.dtb x1p42100-crd-el2.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1-asus-zenbook-a14.dtsi b/arch/arm64/boot/dts/qcom/x1-asus-zenbook-a14.dtsi
new file mode 100644
index 000000000000..c8d6d66d05c8
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1-asus-zenbook-a14.dtsi
@@ -0,0 +1,1302 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1e80100-pmics.dtsi"
+
+/ {
+ model = "ASUS Zenbook A14";
+ chassis-type = "laptop";
+
+ aliases {
+ serial0 = &uart21;
+ serial1 = &uart14;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&hall_int_n_default>;
+ pinctrl-names = "default";
+
+ switch-lid {
+ label = "lid";
+ gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-0 = <&cam_indicator_en>;
+ pinctrl-names = "default";
+
+ led-camera-indicator {
+ label = "white:camera-indicator";
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ /* Reuse as a panic indicator until we get a "camera on" trigger */
+ panic-indicator;
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,x1e80100-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+ <&tlmm 123 GPIO_ACTIVE_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Left-side display-adjacent port */
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss0_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss0_ss_in: endpoint {
+ remote-endpoint = <&retimer_ss0_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss0_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss0_con_sbu_out>;
+ };
+ };
+ };
+ };
+
+ /* Left-side user-adjacent port */
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss1_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss1_ss_in: endpoint {
+ remote-endpoint = <&retimer_ss1_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss1_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss1_con_sbu_out>;
+ };
+ };
+ };
+ };
+ };
+
+ reserved-memory {
+ linux,cma {
+ compatible = "shared-dma-pool";
+ size = <0x0 0x8000000>;
+ reusable;
+ linux,cma-default;
+ };
+ };
+
+ vreg_edp_3p3: regulator-edp-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_EDP_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&edp_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_misc_3p3: regulator-misc-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_MISC_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&misc_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_nvme: regulator-nvme {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_NVME_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_1P15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb0_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb0_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_1P15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb1_pwr_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb1_pwr_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb1_pwr_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_1p9: regulator-wcn-1p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_1P9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob1-supply = <&vreg_vph_pwr>;
+ vdd-bob2-supply = <&vreg_vph_pwr>;
+ vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob2>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l12-supply = <&vreg_s5j_1p2>;
+ vdd-l15-supply = <&vreg_s4c_1p8>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4b_1p8: ldo4 {
+ regulator-name = "vreg_l4b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_3p0: ldo8 {
+ regulator-name = "vreg_l8b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10b_1p8: ldo10 {
+ regulator-name = "vreg_l10b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p2: ldo12 {
+ regulator-name = "vreg_l12b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p0: ldo14 {
+ regulator-name = "vreg_l14b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-l1-supply = <&vreg_s5j_1p2>;
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s4-supply = <&vreg_vph_pwr>;
+
+ vreg_s4c_1p8: smps4 {
+ regulator-name = "vreg_s4c_1p8";
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p2: ldo1 {
+ regulator-name = "vreg_l1c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c_0p8: ldo2 {
+ regulator-name = "vreg_l2c_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_0p9: ldo3 {
+ regulator-name = "vreg_l3c_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-supply = <&vreg_s1f_0p7>;
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s4c_1p8>;
+ vdd-s1-supply = <&vreg_vph_pwr>;
+
+ vreg_l1d_0p8: ldo1 {
+ regulator-name = "vreg_l1d_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2d_0p9: ldo2 {
+ regulator-name = "vreg_l2d_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3d_1p8: ldo3 {
+ regulator-name = "vreg_l3d_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s5j_1p2>;
+
+ vreg_l2e_0p8: ldo2 {
+ regulator-name = "vreg_l2e_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-l1-supply = <&vreg_s5j_1p2>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s5j_1p2>;
+ vdd-s1-supply = <&vreg_vph_pwr>;
+
+ vreg_s1f_0p7: smps1 {
+ regulator-name = "vreg_s1f_0p7";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "i";
+
+ vdd-l1-supply = <&vreg_s4c_1p8>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s1-supply = <&vreg_vph_pwr>;
+ vdd-s2-supply = <&vreg_vph_pwr>;
+
+ vreg_s1i_0p9: smps1 {
+ regulator-name = "vreg_s1i_0p9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2i_1p0: smps2 {
+ regulator-name = "vreg_s2i_1p0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1i_1p8: ldo1 {
+ regulator-name = "vreg_l1i_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2i_1p2: ldo2 {
+ regulator-name = "vreg_l2i_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3i_0p8: ldo3 {
+ regulator-name = "vreg_l3i_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "j";
+
+ vdd-l1-supply = <&vreg_s1f_0p7>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s5-supply = <&vreg_vph_pwr>;
+
+ vreg_s5j_1p2: smps5 {
+ regulator-name = "vreg_s5j_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1j_0p9: ldo1 {
+ regulator-name = "vreg_l1j_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2j_1p2: ldo2 {
+ regulator-name = "vreg_l2j_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1256000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3j_0p8: ldo3 {
+ regulator-name = "vreg_l3j_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ /* ELAN, 04F3:3315 */
+ touchpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-0 = <&tpad_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ /* Left-side display-adjacent port */
+ typec-mux@8 {
+ compatible = "parade,ps8833", "parade,ps8830";
+ reg = <0x08>;
+
+ clocks = <&rpmhcc RPMH_RF_CLK3>;
+
+ vdd-supply = <&vreg_rtmr0_1p15>;
+ vdd33-supply = <&vreg_rtmr0_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+ vddar-supply = <&vreg_rtmr0_1p15>;
+ vddat-supply = <&vreg_rtmr0_1p15>;
+ vddio-supply = <&vreg_rtmr0_1p8>;
+
+ reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&rtmr0_default>;
+ pinctrl-names = "default";
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss0_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss0_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss0_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+ };
+ };
+ };
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ /* ASUSTeK, 0B05:4543 */
+ hdtl@17 {
+ compatible = "hid-over-i2c";
+ reg = <0x17>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 95 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-0 = <&hdtl_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ eusb6_repeater: redriver@4f {
+ compatible = "nxp,ptn3222";
+ reg = <0x4f>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb6_reset_n>;
+ pinctrl-names = "default";
+ };
+
+ /* EC @0x5b */
+};
+
+&i2c7 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ /* Left-side user-adjacent port */
+ typec-mux@8 {
+ compatible = "parade,ps8833", "parade,ps8830";
+ reg = <0x08>;
+
+ clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+ vdd-supply = <&vreg_rtmr1_1p15>;
+ vdd33-supply = <&vreg_rtmr1_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+ vddar-supply = <&vreg_rtmr1_1p15>;
+ vddat-supply = <&vreg_rtmr1_1p15>;
+ vddio-supply = <&vreg_rtmr1_1p8>;
+
+ reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&rtmr1_default>;
+ pinctrl-names = "default";
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss1_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss1_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss1_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+ };
+ };
+ };
+ };
+};
+
+&i2c8 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ /* ASUSTeK, 0B05:0220 */
+ keyboard@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-0 = <&kybd_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+ status = "okay";
+};
+
+&mdss_dp1_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+ /delete-property/ #sound-dai-cells;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+ enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+ power-supply = <&vreg_edp_3p3>;
+
+ pinctrl-0 = <&edp_bl_en>;
+ pinctrl-names = "default";
+
+ port {
+ edp_panel_in: endpoint {
+ remote-endpoint = <&mdss_dp3_out>;
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ reg = <1>;
+
+ mdss_dp3_out: endpoint {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&edp_panel_in>;
+ };
+ };
+ };
+};
+
+&mdss_dp3_phy {
+ vdda-phy-supply = <&vreg_l3j_0p8>;
+ vdda-pll-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&pcie4 {
+ perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l3i_0p8>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&pcie6a {
+ perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+ vddpe-3v3-supply = <&vreg_nvme>;
+
+ pinctrl-0 = <&pcie6a_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie6a_phy {
+ vdda-phy-supply = <&vreg_l1d_0p8>;
+ vdda-pll-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&pm8550_gpios {
+ rtmr0_default: rtmr0-reset-n-active-state {
+ pins = "gpio10";
+ function = "normal";
+ power-source = <1>;
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+
+ usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+ pins = "gpio11";
+ function = "normal";
+ power-source = <1>;
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+};
+
+&pm8550ve_8_gpios {
+ misc_3p3_reg_en: misc-3p3-reg-en-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-disable;
+ input-disable;
+ output-enable;
+ drive-push-pull;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+};
+
+&pm8550ve_9_gpios {
+ usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ power-source = <1>;
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+};
+
+&pmc8380_3_gpios {
+ edp_bl_en: edp-bl-en-state {
+ pins = "gpio4";
+ function = "normal";
+ power-source = <1>;
+ input-disable;
+ output-enable;
+ };
+};
+
+&pmc8380_5_gpios {
+ usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ power-source = <1>;
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+};
+
+&qupv3_0 {
+ status = "okay";
+};
+
+&qupv3_1 {
+ status = "okay";
+};
+
+&qupv3_2 {
+ status = "okay";
+};
+
+&smb2360_0 {
+ status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+ status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&spi10 {
+ status = "disabled";
+
+ /* Unknown device */
+};
+
+&tlmm {
+ gpio-reserved-ranges = <44 4>, /* SPI11, TZ Protected */
+ <90 1>; /* Unknown, TZ Protected */
+
+ cam_indicator_en: cam-indicator-en-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ edp_reg_en: edp-reg-en-state {
+ pins = "gpio70";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ eusb6_reset_n: eusb6-reset-n-state {
+ pins = "gpio184";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ hall_int_n_default: hall-int-n-state {
+ pins = "gpio92";
+ function = "gpio";
+ bias-disable;
+ };
+
+ hdtl_default: hdtl-default-state {
+ pins = "gpio95";
+ function = "gpio";
+ };
+
+ kybd_default: kybd-default-state {
+ pins = "gpio67";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio147";
+ function = "pcie4_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio146";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie6a_default: pcie6a-default-state {
+ clkreq-n-pins {
+ pins = "gpio153";
+ function = "pcie6a_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio152";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio154";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ rtmr1_default: rtmr1-reset-n-active-state {
+ pins = "gpio176";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tpad_default: tpad-default-state {
+ pins = "gpio3";
+ function = "gpio";
+ bias-disable;
+ };
+
+ usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state {
+ pins = "gpio188";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state {
+ pins = "gpio175";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state {
+ pins = "gpio186";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcn_bt_en: wcn-bt-en-state {
+ pins = "gpio116";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio214";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcn_wlan_en: wcn-wlan-en-state {
+ pins = "gpio117";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+};
+
+&uart21 {
+ compatible = "qcom,geni-debug-uart";
+
+ status = "okay";
+};
+
+&usb_1_ss0_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ phys = <&smb2360_0_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+ vdda-phy-supply = <&vreg_l2j_1p2>;
+ vdda-pll-supply = <&vreg_l1j_0p9>;
+
+ status = "okay";
+};
+
+&usb_1_ss0 {
+ status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+ remote-endpoint = <&retimer_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ phys = <&smb2360_1_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+ vdda-phy-supply = <&vreg_l2j_1p2>;
+ vdda-pll-supply = <&vreg_l2d_0p9>;
+
+ status = "okay";
+};
+
+&usb_1_ss1 {
+ status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+ remote-endpoint = <&retimer_ss1_ss_in>;
+};
+
+&usb_mp {
+ status = "okay";
+};
+
+&usb_mp_hsphy0 {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_hsphy1 {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ phys = <&eusb6_repeater>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3c_0p9>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3c_0p9>;
+
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts b/arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
new file mode 100644
index 000000000000..3c83b7e2d823
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "x1e80100.dtsi"
+#include "x1-asus-zenbook-a14.dtsi"
+
+/ {
+ model = "ASUS Zenbook A14 (UX3407RA)";
+ compatible = "asus,zenbook-a14-ux3407ra", "qcom,x1e80100";
+};
+
+&gpu {
+ status = "okay";
+
+ zap_shader {
+ firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qcdxkmsuc8380.mbn";
+ };
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qcadsp8380.mbn",
+ "qcom/x1e80100/ASUSTeK/zenbook-a14/adsp_dtbs.elf";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qccdsp8380.mbn",
+ "qcom/x1e80100/ASUSTeK/zenbook-a14/cdsp_dtbs.elf";
+
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts b/arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
new file mode 100644
index 000000000000..222decddf3e3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "x1p42100.dtsi"
+#include "x1-asus-zenbook-a14.dtsi"
+
+/delete-node/ &pmc8380_6;
+/delete-node/ &pmc8380_6_thermal;
+
+/ {
+ model = "ASUS Zenbook A14 (UX3407QA)";
+ compatible = "asus,zenbook-a14-ux3407qa", "qcom,x1p42100";
+
+ wcn6855-pmu {
+ compatible = "qcom,wcn6855-pmu";
+
+ vddaon-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_wcn_1p9>;
+ vddpcie1p3-supply = <&vreg_wcn_1p9>;
+ vddpcie1p9-supply = <&vreg_wcn_1p9>;
+ vddpmu-supply = <&vreg_wcn_0p95>;
+ vddpmucx-supply = <&vreg_wcn_0p95>;
+ vddpmumx-supply = <&vreg_wcn_0p95>;
+ vddrfa0p95-supply = <&vreg_wcn_0p95>;
+ vddrfa1p3-supply = <&vreg_wcn_1p9>;
+ vddrfa1p9-supply = <&vreg_wcn_1p9>;
+
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_bt_en>, <&wcn_wlan_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn_0p8: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn_0p8";
+ };
+
+ vreg_pmu_aon_0p8: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p8";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p8: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p8";
+ };
+
+ vreg_pmu_btcmx_0p8: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p8";
+ };
+
+ vreg_pmu_pcie_1p8: ldo5 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo6 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_rfa_0p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo8 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo9 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+ };
+ };
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ firmware-name = "qcom/x1p42100/ASUSTeK/zenbook-a14/qcdxkmsucpurwa.mbn";
+ };
+};
+
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1103";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+
+ qcom,calibration-variant = "UX3407Q";
+ };
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/x1p42100/ASUSTeK/zenbook-a14/qcadsp8380.mbn",
+ "qcom/x1p42100/ASUSTeK/zenbook-a14/adsp_dtbs.elf";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/x1p42100/ASUSTeK/zenbook-a14/qccdsp8380.mbn",
+ "qcom/x1p42100/ASUSTeK/zenbook-a14/cdsp_dtbs.elf";
+
+ status = "okay";
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn6855-bt";
+
+ vddaon-supply = <&vreg_pmu_aon_0p8>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+
+ max-speed = <3000000>;
+ };
+};
--
2.45.2
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v5 0/4] X1E Asus Zenbook A14 support
2025-06-07 20:00 [PATCH v5 0/4] X1E Asus Zenbook A14 support Aleksandrs Vinarskis
2025-06-07 20:00 ` [PATCH v5 4/4] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14 Aleksandrs Vinarskis
@ 2025-06-09 15:01 ` Rob Herring (Arm)
1 sibling, 0 replies; 4+ messages in thread
From: Rob Herring (Arm) @ 2025-06-09 15:01 UTC (permalink / raw)
To: Aleksandrs Vinarskis
Cc: linux-arm-msm, dmitry.baryshkov, Krzysztof Kozlowski,
Conor Dooley, Konrad Dybcio, Bjorn Andersson, linux-kernel,
Konrad Dybcio, maud_spierings, Nikita Travkin, devicetree
On Sat, 07 Jun 2025 22:00:44 +0200, Aleksandrs Vinarskis wrote:
> As requested, 1/4 was merged to linux-next by USB maintainers.
> Resending 4/4 rebased on top of latest linux-next. 2/4, 3/4 already
> landed.
>
>
> With this in mind, and taking into account that this patch was
> already reviewed some time ago, any possibility to still add 4/4 to
> 6.16?
>
> ---
>
> Introduce support for the mentioned laptop.
>
> Particular device exists in two model numbers:
> * UX3407QA: X1P-42-100 or X1-26-100 (as tested)
> * UX3407RA: X1E-78-100
>
> Mostly similar to other X1-based laptops. Notable differences are:
> * Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
> and Qualcomm FastConnect 7800 on UX3407RA
> * USB Type-C retimers are Parade PS8833, appear to behave identical
> to Parade PS8830
> * gpio90 is TZ protected
>
> When comparing device firmware between UX3407QA, UX3407RA, it seems
> that only ADSP firmware is different, CDSP and GPU firmware appears to
> be the same. (At least assuming the GPU firmware name in both cases is
> `qcdxkmsuc8380.mbn`). Since at least some blobs are different betweeen
> X1E and X1/X1P, define new firmware directory for `qcom/x1p42100`. This
> also makes it easier for distros to automatically extract firmware from
> Windows and place all blobs for the model under the same path. If/When
> firmware blobs make it to linux-firmware, same blobs can be easily
> symlinked between `qcom/x1e80100` and `qcom/x1p42100`.
>
> NVMe SSD depends on [1]. USB Type-A over USB MP controller depends on
> [2], or equivalent proposed solution.
>
> Qualcomm FastConnect 6900 on UX3407QA did not work out of the box, and
> additionally required both newer firmware and patches to `board-2.bin`.
> I added a short how-to [3], as it is not exactly trivial.
>
> ACPI dumps can be found on aarch64-laptops' github [4]. HWids on
> dtbloader's github [5].
>
> [1] https://lore.kernel.org/linux-arm-msm/20250319094544.3980357-1-quic_wenbyao@quicinc.com/
> [2] https://lore.kernel.org/all/20250318-xps13-fingerprint-v1-1-fbb02d5a34a7@oss.qualcomm.com/
> [3] https://github.com/alexVinarskis/linux-x1e80100-zenbook-a14?tab=readme-ov-file#wcn688x-wifi
> [4] https://github.com/aarch64-laptops/build/pull/134/files
> [5] https://github.com/TravMurav/dtbloader/pull/4/files
> [6] https://lore.kernel.org/all/20250429-x1e80100-dts-drop-useless-dp-compatible-override-v1-0-058847814d70@linaro.org/
> [7] https://lore.kernel.org/all/20250524-tb16-dt-v4-5-2c1e6018d3f0@oldschoolsolutions.biz/
>
> Changes to v5:
> * _Only sending 4/4 as other patches are already applied_
> * Rebase 4/4 on `next-20250606`
> * Moved gpu enable from dtsi to respective dts as per discussion in [7]
> Link to v5: https://lore.kernel.org/all/20250523131605.6624-1-alex.vinarskis@gmail.com/
>
> Changes to v4:
> * _Only sending 4/4 as other patches are already applied_
> * Rebase 4/4 on `for-next` of qcom tree, adjust makefile to generate el2 dtbs
> * Picked Konrad's R-by for 4/4
> * Droped 'qcom,x1e80100-dp' as per [6]
> Link to v4: https://lore.kernel.org/all/20250426130203.37659-1-alex.vinarskis@gmail.com/
>
> Changes to v3:
> * Drop redundant comments
> * Drop incomplete wcn7850 as it is causing dt errors
> * Picked a-by
> Link to v3: https://lore.kernel.org/all/20250416232345.5240-1-alex.vinarskis@gmail.com/
>
> Changes to v2:
> * Fix/re-add PS8833 as fallback
> * Add EC's i2c address
> * Add pwrseq for wcn6855, placeholder for wcn7850 until its tested
> * Rename x1-zenbook.dtsi to x1-asus-zenbook.dtsi
> Link to v2: https://lore.kernel.org/all/20250402084646.10098-1-alex.vinarskis@gmail.com/
>
> Changes to v1:
> * Drop PS8833 variant, fallback to PS8830 as they behave the same
> * Drop wrong pcie6a_phy compatible revert
> * Drop redundant comments, fix order of properties in the device-tree
> * Fix device name bindings, express in model names instead of the soc
> * Fix GPU firmware name for UX3407QA
> * Fix model string, enclose variant in parenthesis
> * Added missing new lines before 'status = "okay";'
> * Updated cover letter to reflect some of the above changes
> * Left SPI10 disabled as it is unknown how/what for to use it as of now
> Link to v1: https://lore.kernel.org/all/20250331215720.19692-1-alex.vinarskis@gmail.com/
>
> Aleksandrs Vinarskis (1):
> arm64: dts: qcom: Add support for X1-based Asus Zenbook A14
>
> arch/arm64/boot/dts/qcom/Makefile | 4 +
> .../boot/dts/qcom/x1-asus-zenbook-a14.dtsi | 1302 +++++++++++++++++
> .../dts/qcom/x1e80100-asus-zenbook-a14.dts | 37 +
> .../dts/qcom/x1p42100-asus-zenbook-a14.dts | 141 ++
> 4 files changed, 1484 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/x1-asus-zenbook-a14.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
> create mode 100644 arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
>
> --
> 2.45.2
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
This patch series was applied (using b4) to base:
Base: attempting to guess base-commit...
Base: tags/next-20250606 (exact match)
If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)
New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20250607200229.30538-1-alex.vinarskis@gmail.com:
arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dtb: gpu@3d00000 (qcom,adreno-43050c01): 'zap_shader' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/display/msm/gpu.yaml#
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v5 4/4] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14
2025-06-07 20:00 ` [PATCH v5 4/4] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14 Aleksandrs Vinarskis
@ 2025-06-10 11:58 ` Konrad Dybcio
0 siblings, 0 replies; 4+ messages in thread
From: Konrad Dybcio @ 2025-06-10 11:58 UTC (permalink / raw)
To: Aleksandrs Vinarskis, Bjorn Andersson, Nikita Travkin,
Konrad Dybcio, linux-arm-msm, devicetree, linux-kernel
Cc: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
dmitry.baryshkov, maud_spierings
On 6/7/25 10:00 PM, Aleksandrs Vinarskis wrote:
> Initial support for Asus Zenbook A14. Particular moddel exists
> in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).
>
> Mostly similar to other X1-based laptops. Notable differences are:
> * Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
> and Qualcomm FastConnect 7800 on UX3407RA
> * USB Type-C retimers are Parade PS8833, appear to behave identical
> to Parade PS8830
> * gpio90 is TZ protected
>
> Working:
> * Keyboard
> * Touchpad
> * NVME
> * Lid switch
> * Camera LED
> * eDP (FHD OLED, SDC420D) with brightness control
> * Bluetooth, WiFi (WCN6855)
> * USB Type-A port
> * USB Type-C ports in USB2/USB3/DP (both orientations)
> * aDSP/cDPS firmware loading, battery info
> * Sleep/suspend, nothing visibly broken on resume
>
> Out of scope of this series:
> * Audio (Speakers/microphones/headphone jack)
> * Camera (OmniVision OV02C10)
> * HDMI (Parade PS185HDM)
> * EC
>
> Add dtsi and create two configurations for UX3407QA, UX3407RA.
> Tested on UX3407QA with X1-26-100.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
> ---
[...]
> +&gpu {
> + status = "okay";
> +
> + zap_shader {
> + firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qcdxkmsuc8380.mbn";
> + };
> +};
Override &gpu_zap_shader {} instead, this doesn't work as pointed out by Rob's bot
Also in the second dt
Konrad
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2025-06-10 11:58 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-06-07 20:00 [PATCH v5 0/4] X1E Asus Zenbook A14 support Aleksandrs Vinarskis
2025-06-07 20:00 ` [PATCH v5 4/4] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14 Aleksandrs Vinarskis
2025-06-10 11:58 ` Konrad Dybcio
2025-06-09 15:01 ` [PATCH v5 0/4] X1E Asus Zenbook A14 support Rob Herring (Arm)
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).