[net-next PATCH v15 00/12] net: dsa: Add Airoha AN8855 support

[net-next PATCH v15 00/12] net: dsa: Add Airoha AN8855 support

[Christian Marangi]

This series add the initial support for the Airoha AN8855 Switch.

It's a 5 port Gigabit Switch with SGMII/HSGMII upstream port.

This is starting to get in the wild and there are already some router
having this switch chip.

It's conceptually similar to mediatek switch but register and bits
are different. And there is massive list of register for the PCS
configuration.
Saddly for that part we have absolutely NO documentation currently.

There is this special thing where PHY needs to be calibrated with values
from the switch efuse. (the thing have a whole cpu timer and MCU)

Some interesting HW BUG were discovered while implementing MDIO PBUS
access.

From v8 Driver is now evaluated with Kernel selftest scripts for DSA:

Additional info about the test bridge_vlan_aware.sh.

It was discovered that the Airoha Switch (and probably the Mediatek one
that produce the same test results) hardcode checking for 802.1ad when
the port is configured in VLAN-Aware mode (aka Security mode).

In such mode, both 802.1q and 802.1ad TPID are checked, hence the
bridge_vlan_aware.sh test fails as packets with 802.1ad TPID are rejected
(in the case where a wrong VLAN ID is forwarded)

This was confirmed by Airoha and multiple try were done to try to
workaround this problem. No solution were found to this as ACL mechanism
can't work on receiving packets and the Switch doesn't support turning off
this.

The current driver is in use from 4 month on OpenWrt with all kind of
scenario confirming working in VLAN bridge. By tweaking the
bridge_vlan_aware.sh test with setting the TPID to 0x9100, the test
correctly pass as packets gets classified as untagged and the default PVID
applied. It's also confirmed that switch correctly parse the 802.1ad tag
and make the packet pass only when allowed by VLAN table rules.

Output local_termination.sh
TEST: lan2: Unicast IPv4 to primary MAC address                     [ OK ]
TEST: lan2: Unicast IPv4 to macvlan MAC address                     [ OK ]
TEST: lan2: Unicast IPv4 to unknown MAC address                     [ OK ]
TEST: lan2: Unicast IPv4 to unknown MAC address, promisc            [ OK ]
TEST: lan2: Unicast IPv4 to unknown MAC address, allmulti           [ OK ]
TEST: lan2: Multicast IPv4 to joined group                          [ OK ]
TEST: lan2: Multicast IPv4 to unknown group                         [XFAIL]
        reception succeeded, but should have failed
TEST: lan2: Multicast IPv4 to unknown group, promisc                [ OK ]
TEST: lan2: Multicast IPv4 to unknown group, allmulti               [ OK ]
TEST: lan2: Multicast IPv6 to joined group                          [ OK ]
TEST: lan2: Multicast IPv6 to unknown group                         [XFAIL]
        reception succeeded, but should have failed
TEST: lan2: Multicast IPv6 to unknown group, promisc                [ OK ]
TEST: lan2: Multicast IPv6 to unknown group, allmulti               [ OK ]
TEST: lan2: 1588v2 over L2 transport, Sync                          [ OK ]
TEST: lan2: 1588v2 over L2 transport, Follow-Up                     [ OK ]
TEST: lan2: 1588v2 over L2 transport, Peer Delay Request            [ OK ]
TEST: lan2: 1588v2 over IPv4, Sync                                  [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv4, Follow-Up                             [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv4, Peer Delay Request                    [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv6, Sync                                  [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv6, Follow-Up                             [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv6, Peer Delay Request                    [FAIL]
        reception failed
TEST: vlan_filtering=0 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv4 to joined group       [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv4 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=0 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv6 to joined group       [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv6 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=0 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv4 to joined group       [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv4 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=1 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv6 to joined group       [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv6 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=1 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN upper: Unicast IPv4 to primary MAC address               [ OK ]
TEST: VLAN upper: Unicast IPv4 to macvlan MAC address               [ OK ]
TEST: VLAN upper: Unicast IPv4 to unknown MAC address               [ OK ]
TEST: VLAN upper: Unicast IPv4 to unknown MAC address, promisc      [ OK ]
TEST: VLAN upper: Unicast IPv4 to unknown MAC address, allmulti     [ OK ]
TEST: VLAN upper: Multicast IPv4 to joined group                    [ OK ]
TEST: VLAN upper: Multicast IPv4 to unknown group                   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN upper: Multicast IPv4 to unknown group, promisc          [ OK ]
TEST: VLAN upper: Multicast IPv4 to unknown group, allmulti         [ OK ]
TEST: VLAN upper: Multicast IPv6 to joined group                    [ OK ]
TEST: VLAN upper: Multicast IPv6 to unknown group                   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN upper: Multicast IPv6 to unknown group, promisc          [ OK ]
TEST: VLAN upper: Multicast IPv6 to unknown group, allmulti         [ OK ]
TEST: VLAN upper: 1588v2 over L2 transport, Sync                    [ OK ]
TEST: VLAN upper: 1588v2 over L2 transport, Follow-Up               [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over L2 transport, Peer Delay Request      [ OK ]
TEST: VLAN upper: 1588v2 over IPv4, Sync                            [FAIL]
        reception failed
;TEST: VLAN upper: 1588v2 over IPv4, Follow-Up                       [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv4, Peer Delay Request              [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv6, Sync                            [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv6, Follow-Up                       [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv6, Peer Delay Request              [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over L2 transport, Sync   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over L2 transport, Follow-Up   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over L2 transport, Peer Delay Request   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv4, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv4, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv4, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv6, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv6, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv6, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address   [FAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, allmulti   [FAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over L2 transport, Sync   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over L2 transport, Follow-Up   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over L2 transport, Peer Delay Request   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv4, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv4, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv4, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv6, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv6, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv6, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]

Output bridge_vlan_unaware.sh
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: FDB learning                                                  [ OK ]
TEST: Unknown unicast flood                                         [ OK ]
TEST: Unregistered multicast flood                                  [ OK ]

Output bridge_vlan_aware.sh
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: FDB learning                                                  [ OK ]
TEST: Unknown unicast flood                                         [ OK ]
TEST: Unregistered multicast flood                                  [ OK ]
INFO: Add and delete a VLAN on bridge port lan2
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: Externally learned FDB entry - ageing & roaming               [ OK ]
TEST: FDB entry in PVID for VLAN-tagged with other TPID             [FAIL]
        FDB entry was not learned when it should
TEST: Reception of VLAN with other TPID as untagged                 [FAIL]
        Packet was not forwarded when it should
TEST: Reception of VLAN with other TPID as untagged (no PVID)       [FAIL]
        Packet was forwarded when should not

[ For Vladimir, I still have to implement fdb_isolation but posting to
start the ball rolling for the multiple subsystem this patch affect
and for the dubious DT schema ]

Changes v15:
- Rebase on top of net-next
- Drop regmap MDIO patch (in favor of PBUS)
- Implement MDIO PBUS and rework MDIO driver/MFD
- Reimplement EEE support
- Add some check for regmap from MFD
- Move to single regmap and add comments with all findings
Changes v14:
- Move MAITAINERS entry to dedicated commit (make it easier for cross
  subsystem merge)
- Pack variables in trap function
- Add additional patch for reported difference from MTK tag
Changes v13:
- Reimplement tx_lpi OPs
- Rework mdio-regmap to internally encode/decode address
- Fix error in Documentation
- Drop ext-surge property (assume calibration with declared nvmem cell)
- Fix comments from Lee on MFD driver
- Improve print error and drop extra space in DSA driver
Changes v12:
- Update on top of net-next
- Add additional info on conver-letter about slefttests and HW limitation
- Introduce mdio-regmap generalization for multiple address
- Drop dev flags and define PHY calibration in PHY node directly
Changes v11:
- Address reviews from Christophe (spell mistake + dev_err_probe)
- Fix kconfig dependency for MFD driver (depends on MDIO_DEVICE instead of MDIO)
  (indirectly fix link error for mdio APIs)
- Fix copy-paste error for MFD driver of_table
- Fix compilation error for PHY (move NVMEM to .config)
- Drop unneeded NVMEM node from MDIO example schema (from Andrew)
- Adapt MFD example schema to MDIO reg property restrictions
Changes v10:
- Entire rework to MFD + split to MDIO, EFUSE, SWITCH separate drivers
- Drop EEE OPs (while Russell finish RFC for EEE changes)
- Use new pcs_inpand OPs
- Drop AN restart function and move to pcs_config
- Enable assisted_learning and disable CPU learn (preparation for fdb_isolation)
- Move EFUSE read in Internal PHY driver to .config to handle EPROBE_DEFER
  (needed now that NVMEM driver is register externally instead of internally to switch
   node)
Changes v9:
- Error out on using 5G speed as currently not supported
- Add missing MAC_2500FD in phylink mac_capabilities
- Add comment and improve if condition for an8855_phylink_mac_config
Changes v8:
- Add port Fast Age support
- Add support for Port Isolation
- Use correct register for Learning Disable
- Add support for Ageing Time OP
- Set default PVID to 0 by default
- Add mdb OPs
- Add port change MTU
- Fix support for Upper VLAN
Changes v7:
- Fix devm_dsa_register_switch wrong export symbol
Changes v6:
- Drop standard MIB and handle with ethtool OPs (as requested by Jakub)
- Cosmetic: use bool instead of 0 or 1
Changes v5:
- Add devm_dsa_register_switch() patch
- Add Reviewed-by tag for DT patch
Changes v4:
- Set regmap readable_table static (mute compilation warning)
- Add support for port_bridge flags (LEARNING, FLOOD)
- Reset fdb struct in fdb_dump
- Drop support_asym_pause in port_enable
- Add define for get_phy_flags
- Fix bug for port not inititially part of a bridge
  (in an8855_setup the port matrix was always cleared but
   the CPU port was never initially added)
- Disable learning and flood for user port by default
- Set CPU port to flood and learning by default
- Correctly AND force duplex and flow control in an8855_phylink_mac_link_up
- Drop RGMII from pcs_config
- Check ret in "Disable AN if not in autoneg"
- Use devm_mutex_init
- Fix typo for AN8855_PORT_CHECK_MODE
- Better define AN8855_STP_LISTENING = AN8855_STP_BLOCKING
- Fix typo in AN8855_PHY_EN_DOWN_SHIFT
- Use paged helper for PHY
- Skip calibration in config_init if priv not defined
Changes v3:
- Out of RFC
- Switch PHY code to select_page API
- Better describe masks and bits in PHY driver for ADC register
- Drop raw values and use define for mii read/write
- Switch to absolute PHY address
- Replace raw values with mask and bits for pcs_config
- Fix typo for ext-surge property name
- Drop support for relocating Switch base PHY address on the bus
Changes v2:
- Drop mutex guard patch
- Drop guard usage in DSA driver
- Use __mdiobus_write/read
- Check return condition and return errors for mii read/write
- Fix wrong logic for EEE
- Fix link_down (don't force link down with autoneg)
- Fix forcing speed on sgmii autoneg
- Better document link speed for sgmii reg
- Use standard define for sgmii reg
- Imlement nvmem support to expose switch EFUSE
- Rework PHY calibration with the use of NVMEM producer/consumer
- Update DT with new NVMEM property
- Move aneg validation for 2500-basex in pcs_config
- Move r50Ohm table and function to PHY driver

Christian Marangi (12):
  dt-bindings: nvmem: Document support for Airoha AN8855 Switch EFUSE
  dt-bindings: net: Document support for Airoha AN8855 Switch PBUS MDIO
  dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch
  dt-bindings: net: Document support for AN8855 Switch Internal PHY
  dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC
  net: mdio: Add Airoha AN8855 Switch MDIO PBUS
  nvmem: an8855: Add support for Airoha AN8855 Switch EFUSE
  net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver
  mfd: an8855: Add support for Airoha AN8855 Switch MFD
  net: phy: Add Airoha AN8855 Internal Switch Gigabit PHY
  MAINTAINERS: add myself as maintainer for AN8855
  net: dsa: tag_mtk: add comments about Airoha usage of this TAG

 .../bindings/mfd/airoha,an8855.yaml           |  175 ++
 .../bindings/net/airoha,an8855-mdio.yaml      |   57 +
 .../bindings/net/airoha,an8855-phy.yaml       |   83 +
 .../net/dsa/airoha,an8855-switch.yaml         |   86 +
 .../bindings/nvmem/airoha,an8855-efuse.yaml   |  123 +
 MAINTAINERS                                   |   19 +
 drivers/mfd/Kconfig                           |   12 +
 drivers/mfd/Makefile                          |    1 +
 drivers/mfd/airoha-an8855.c                   |  393 +++
 drivers/net/dsa/Kconfig                       |    9 +
 drivers/net/dsa/Makefile                      |    1 +
 drivers/net/dsa/an8855.c                      | 2386 +++++++++++++++++
 drivers/net/dsa/an8855.h                      |  773 ++++++
 drivers/net/mdio/Kconfig                      |   10 +
 drivers/net/mdio/Makefile                     |    1 +
 drivers/net/mdio/mdio-an8855.c                |  262 ++
 drivers/net/phy/Kconfig                       |    5 +
 drivers/net/phy/Makefile                      |    1 +
 drivers/net/phy/air_an8855.c                  |  261 ++
 drivers/nvmem/Kconfig                         |   11 +
 drivers/nvmem/Makefile                        |    2 +
 drivers/nvmem/an8855-efuse.c                  |   68 +
 include/linux/dsa/an8855.h                    |   18 +
 net/dsa/tag_mtk.c                             |    3 +
 24 files changed, 4760 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
 create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 create mode 100644 Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 create mode 100644 drivers/mfd/airoha-an8855.c
 create mode 100644 drivers/net/dsa/an8855.c
 create mode 100644 drivers/net/dsa/an8855.h
 create mode 100644 drivers/net/mdio/mdio-an8855.c
 create mode 100644 drivers/net/phy/air_an8855.c
 create mode 100644 drivers/nvmem/an8855-efuse.c
 create mode 100644 include/linux/dsa/an8855.h

-- 
2.48.1

[net-next PATCH v15 01/12] dt-bindings: nvmem: Document support for Airoha AN8855 Switch EFUSE

[Christian Marangi]

Document support for Airoha AN8855 Switch EFUSE used to calibrate
internal PHYs and store additional configuration info.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/nvmem/airoha,an8855-efuse.yaml   | 123 ++++++++++++++++++
 1 file changed, 123 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml

diff --git a/Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml b/Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
new file mode 100644
index 000000000000..9802d9ea2176
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/airoha,an8855-efuse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Switch EFUSE
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description:
+  Airoha AN8855 EFUSE used to calibrate internal PHYs and store additional
+  configuration info.
+
+$ref: nvmem.yaml#
+
+properties:
+  compatible:
+    const: airoha,an8855-efuse
+
+  '#nvmem-cell-cells':
+    const: 0
+
+required:
+  - compatible
+  - '#nvmem-cell-cells'
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    efuse {
+        compatible = "airoha,an8855-efuse";
+
+        #nvmem-cell-cells = <0>;
+
+        nvmem-layout {
+            compatible = "fixed-layout";
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
+               reg = <0xc 0x4>;
+            };
+
+            shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
+                reg = <0x10 0x4>;
+            };
+
+            shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
+                reg = <0x14 0x4>;
+            };
+
+            shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
+               reg = <0x18 0x4>;
+            };
+
+            shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
+               reg = <0x1c 0x4>;
+            };
+
+            shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
+               reg = <0x20 0x4>;
+            };
+
+            shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
+               reg = <0x24 0x4>;
+            };
+
+            shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
+               reg = <0x28 0x4>;
+            };
+
+            shift_sel_port2_tx_a: shift-sel-port2-tx-a@2c {
+                reg = <0x2c 0x4>;
+            };
+
+            shift_sel_port2_tx_b: shift-sel-port2-tx-b@30 {
+                reg = <0x30 0x4>;
+            };
+
+            shift_sel_port2_tx_c: shift-sel-port2-tx-c@34 {
+                reg = <0x34 0x4>;
+            };
+
+            shift_sel_port2_tx_d: shift-sel-port2-tx-d@38 {
+                reg = <0x38 0x4>;
+            };
+
+            shift_sel_port3_tx_a: shift-sel-port3-tx-a@4c {
+                reg = <0x4c 0x4>;
+            };
+
+            shift_sel_port3_tx_b: shift-sel-port3-tx-b@50 {
+                reg = <0x50 0x4>;
+            };
+
+            shift_sel_port3_tx_c: shift-sel-port3-tx-c@54 {
+               reg = <0x54 0x4>;
+            };
+
+            shift_sel_port3_tx_d: shift-sel-port3-tx-d@58 {
+               reg = <0x58 0x4>;
+            };
+
+            shift_sel_port4_tx_a: shift-sel-port4-tx-a@5c {
+                reg = <0x5c 0x4>;
+            };
+
+            shift_sel_port4_tx_b: shift-sel-port4-tx-b@60 {
+                reg = <0x60 0x4>;
+            };
+
+            shift_sel_port4_tx_c: shift-sel-port4-tx-c@64 {
+                reg = <0x64 0x4>;
+            };
+
+            shift_sel_port4_tx_d: shift-sel-port4-tx-d@68 {
+                reg = <0x68 0x4>;
+            };
+        };
+    };
-- 
2.48.1

[net-next PATCH v15 02/12] dt-bindings: net: Document support for Airoha AN8855 Switch PBUS MDIO

[Christian Marangi]

Document support for Airoha AN8855 PBUS MDIO. Airoha AN8855 Switch
expose a way to access internal PHYs via Switch register.
This is named internally PBUS and does the function of an MDIO bus
for the internal PHYs.

It does support a maximum of 5 PHYs (matching the number of port
the Switch support)

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/net/airoha,an8855-mdio.yaml      | 57 +++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml

diff --git a/Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml b/Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
new file mode 100644
index 000000000000..c873103d2b66
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/airoha,an8855-mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 PBUS MDIO
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description:
+  Airoha AN8855 Switch expose a way to access internal PHYs via
+  Switch register. This is named internally PBUS and does the function
+  of an MDIO bus for the internal PHYs.
+
+  It does support a maximum of 5 PHYs (matching the number of port
+  the Switch support)
+
+$ref: /schemas/net/mdio.yaml#
+
+properties:
+  compatible:
+    const: airoha,an8855-mdio
+
+required:
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        compatible = "airoha,an8855-mdio";
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        internal_phy1: phy@1 {
+            reg = <1>;
+        };
+
+        internal_phy2: phy@2 {
+            reg = <2>;
+        };
+
+        internal_phy3: phy@3 {
+            reg = <3>;
+        };
+
+        internal_phy4: phy@4 {
+            reg = <4>;
+        };
+
+        internal_phy5: phy@5 {
+            reg = <5>;
+        };
+    };
-- 
2.48.1

[net-next PATCH v15 03/12] dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch

[Christian Marangi]

Document support for Airoha AN8855 5-port Gigabit Switch.

It does expose the 5 Internal PHYs on the MDIO bus and each port
can access the Switch register space by configurting the PHY page.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../net/dsa/airoha,an8855-switch.yaml         | 86 +++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml

diff --git a/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
new file mode 100644
index 000000000000..fbb9219fadae
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/airoha,an8855-switch.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Gigabit Switch
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: >
+  Airoha AN8855 is a 5-port Gigabit Switch.
+
+  It does expose the 5 Internal PHYs on the MDIO bus and each port
+  can access the Switch register space by configurting the PHY page.
+
+$ref: dsa.yaml#/$defs/ethernet-ports
+
+properties:
+  compatible:
+    const: airoha,an8855-switch
+
+required:
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    ethernet-switch {
+        compatible = "airoha,an8855-switch";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                label = "lan1";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy1>;
+            };
+
+            port@1 {
+                reg = <1>;
+                label = "lan2";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy2>;
+            };
+
+            port@2 {
+                reg = <2>;
+                label = "lan3";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy3>;
+            };
+
+            port@3 {
+                reg = <3>;
+                label = "lan4";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy4>;
+            };
+
+            port@4 {
+                reg = <4>;
+                label = "wan";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy5>;
+            };
+
+            port@5 {
+                reg = <5>;
+                label = "cpu";
+                ethernet = <&gmac0>;
+                phy-mode = "2500base-x";
+
+                fixed-link {
+                    speed = <2500>;
+                    full-duplex;
+                    pause;
+                };
+            };
+        };
+    };
-- 
2.48.1

[net-next PATCH v15 04/12] dt-bindings: net: Document support for AN8855 Switch Internal PHY

[Christian Marangi]

Document support for AN8855 Switch Internal PHY.

Airoha AN8855 is a 5-port Gigabit Switch that expose the Internal
PHYs on the MDIO bus.

Each PHY might need to be calibrated to correctly work with the
use of the eFUSE provided by the Switch SoC. This can be enabled by
defining in the PHY node the NVMEM cell properties.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/net/airoha,an8855-phy.yaml       | 83 +++++++++++++++++++
 1 file changed, 83 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml

diff --git a/Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml b/Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
new file mode 100644
index 000000000000..d2f86116badf
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/airoha,an8855-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Switch Internal PHY
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: >
+  Airoha AN8855 is a 5-port Gigabit Switch that expose the Internal
+  PHYs on the MDIO bus.
+
+  Each PHY might need to be calibrated to correctly work with the
+  use of the eFUSE provided by the Switch SoC.
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - ethernet-phy-idc0ff.0410
+  required:
+    - compatible
+
+properties:
+  reg:
+    maxItems: 1
+
+  nvmem-cells:
+    items:
+      - description: phandle to SoC eFUSE tx_a
+      - description: phandle to SoC eFUSE tx_b
+      - description: phandle to SoC eFUSE tx_c
+      - description: phandle to SoC eFUSE tx_d
+
+  nvmem-cell-names:
+    items:
+      - const: tx_a
+      - const: tx_b
+      - const: tx_c
+      - const: tx_d
+
+required:
+  - compatible
+  - reg
+
+dependentRequired:
+  nvmem-cells: [ nvmem-cell-names ]
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-phy@1 {
+            compatible = "ethernet-phy-idc0ff.0410",
+                         "ethernet-phy-ieee802.3-c45";
+
+            reg = <1>;
+        };
+
+        ethernet-phy@2 {
+            compatible = "ethernet-phy-idc0ff.0410",
+                         "ethernet-phy-ieee802.3-c45";
+
+            reg = <2>;
+
+            nvmem-cells = <&shift_sel_port0_tx_a>,
+                          <&shift_sel_port0_tx_b>,
+                          <&shift_sel_port0_tx_c>,
+                          <&shift_sel_port0_tx_d>;
+            nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+        };
+    };
-- 
2.48.1

[net-next PATCH v15 05/12] dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC

[Christian Marangi]

Document support for Airoha AN8855 Switch SoC. This SoC expose various
peripherals like an Ethernet Switch, a NVMEM provider and Ethernet PHYs.

It does also support i2c and timers but those are not currently
supported/used.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/mfd/airoha,an8855.yaml           | 175 ++++++++++++++++++
 1 file changed, 175 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml

diff --git a/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
new file mode 100644
index 000000000000..a683db4f41d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/airoha,an8855.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Switch SoC
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: >
+  Airoha AN8855 Switch is a SoC that expose various peripherals like an
+  Ethernet Switch, a NVMEM provider and Ethernet PHYs.
+
+  It does also support i2c and timers but those are not currently
+  supported/used.
+
+properties:
+  compatible:
+    const: airoha,an8855
+
+  reg:
+    maxItems: 1
+
+  reset-gpios: true
+
+  efuse:
+    type: object
+    $ref: /schemas/nvmem/airoha,an8855-efuse.yaml
+    description: EFUSE exposed by the Airoha AN8855 SoC
+
+  ethernet-switch:
+    type: object
+    $ref: /schemas/net/dsa/airoha,an8855-switch.yaml
+    description: Switch exposed by the Airoha AN8855 SoC
+
+  mdio:
+    type: object
+    $ref: /schemas/net/airoha,an8855-mdio.yaml
+    description: MDIO exposed by the Airoha AN8855 SoC
+
+required:
+  - compatible
+  - reg
+  - mdio
+  - ethernet-switch
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        soc@1 {
+            compatible = "airoha,an8855";
+            reg = <1>;
+
+            reset-gpios = <&pio 39 0>;
+
+            efuse {
+                compatible = "airoha,an8855-efuse";
+
+                #nvmem-cell-cells = <0>;
+
+                nvmem-layout {
+                    compatible = "fixed-layout";
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+
+                    shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
+                       reg = <0xc 0x4>;
+                    };
+
+                    shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
+                        reg = <0x10 0x4>;
+                    };
+
+                    shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
+                        reg = <0x14 0x4>;
+                    };
+
+                    shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
+                       reg = <0x18 0x4>;
+                    };
+
+                    shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
+                        reg = <0x1c 0x4>;
+                    };
+
+                    shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
+                        reg = <0x20 0x4>;
+                    };
+
+                    shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
+                       reg = <0x24 0x4>;
+                    };
+
+                    shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
+                        reg = <0x28 0x4>;
+                    };
+                };
+            };
+
+            ethernet-switch {
+                compatible = "airoha,an8855-switch";
+
+                ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        label = "lan1";
+                        phy-mode = "internal";
+                        phy-handle = <&internal_phy1>;
+                    };
+
+                    port@1 {
+                        reg = <1>;
+                        label = "lan2";
+                        phy-mode = "internal";
+                        phy-handle = <&internal_phy2>;
+                    };
+
+                    port@5 {
+                        reg = <5>;
+                        label = "cpu";
+                        ethernet = <&gmac0>;
+                        phy-mode = "2500base-x";
+
+                        fixed-link {
+                            speed = <2500>;
+                            full-duplex;
+                            pause;
+                        };
+                    };
+                };
+            };
+
+            mdio {
+                compatible = "airoha,an8855-mdio";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                internal_phy1: ethernet-phy@1 {
+                  compatible = "ethernet-phy-idc0ff.0410",
+                               "ethernet-phy-ieee802.3-c22";
+                  reg = <1>;
+
+                  nvmem-cells = <&shift_sel_port0_tx_a>,
+                      <&shift_sel_port0_tx_b>,
+                      <&shift_sel_port0_tx_c>,
+                      <&shift_sel_port0_tx_d>;
+                  nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+
+                internal_phy2: ethernet-phy@2 {
+                  compatible = "ethernet-phy-idc0ff.0410",
+                               "ethernet-phy-ieee802.3-c22";
+                  reg = <2>;
+
+                  nvmem-cells = <&shift_sel_port1_tx_a>,
+                      <&shift_sel_port1_tx_b>,
+                      <&shift_sel_port1_tx_c>,
+                      <&shift_sel_port1_tx_d>;
+                  nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+            };
+        };
+    };
-- 
2.48.1

[net-next PATCH v15 06/12] net: mdio: Add Airoha AN8855 Switch MDIO PBUS

[Christian Marangi]

Add Airoha AN8855 MDIO PBUS driver that permits to access the internal
Gigabit PHY from the Switch register.

This have the benefits of exposing direct access to CL45 address and
Vendor MDIO pages via specific Switch registers.

Additional info are present in a long explaination in the MDIO driver
and also finding from Reverse-Engineering the implementation.

This requires the upper Switch MFD to be probed and init to actually
work as it does make use of regmap.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/mdio/Kconfig       |  10 ++
 drivers/net/mdio/Makefile      |   1 +
 drivers/net/mdio/mdio-an8855.c | 262 +++++++++++++++++++++++++++++++++
 include/linux/dsa/an8855.h     |  18 +++
 4 files changed, 291 insertions(+)
 create mode 100644 drivers/net/mdio/mdio-an8855.c
 create mode 100644 include/linux/dsa/an8855.h

diff --git a/drivers/net/mdio/Kconfig b/drivers/net/mdio/Kconfig
index 7db40aaa079d..7f8f0b5caa42 100644
--- a/drivers/net/mdio/Kconfig
+++ b/drivers/net/mdio/Kconfig
@@ -42,6 +42,16 @@ config MDIO_XGENE
 	  This module provides a driver for the MDIO busses found in the
 	  APM X-Gene SoC's.
 
+config MDIO_AN8855
+	tristate "Airoha AN8855 Switch MDIO bus controller"
+	depends on MFD_AIROHA_AN8855
+	depends on OF_MDIO
+	select MDIO_REGMAP
+	help
+	  This module provides a driver for the Airoha AN8855 Switch
+	  that requires a MDIO passtrough as switch address is shared
+	  with the internal PHYs and requires additional page handling.
+
 config MDIO_ASPEED
 	tristate "ASPEED MDIO bus controller"
 	depends on ARCH_ASPEED || COMPILE_TEST
diff --git a/drivers/net/mdio/Makefile b/drivers/net/mdio/Makefile
index c23778e73890..2b9edddf3911 100644
--- a/drivers/net/mdio/Makefile
+++ b/drivers/net/mdio/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_ACPI_MDIO)		+= acpi_mdio.o
 obj-$(CONFIG_FWNODE_MDIO)	+= fwnode_mdio.o
 obj-$(CONFIG_OF_MDIO)		+= of_mdio.o
 
+obj-$(CONFIG_MDIO_AN8855)		+= mdio-an8855.o
 obj-$(CONFIG_MDIO_ASPEED)		+= mdio-aspeed.o
 obj-$(CONFIG_MDIO_BCM_IPROC)		+= mdio-bcm-iproc.o
 obj-$(CONFIG_MDIO_BCM_UNIMAC)		+= mdio-bcm-unimac.o
diff --git a/drivers/net/mdio/mdio-an8855.c b/drivers/net/mdio/mdio-an8855.c
new file mode 100644
index 000000000000..990cf683b470
--- /dev/null
+++ b/drivers/net/mdio/mdio-an8855.c
@@ -0,0 +1,262 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * MDIO PBUS driver for Airoha AN8855 Switch
+ *
+ * Author: Christian Marangi <ansuelsmth@gmail.com>
+ *
+ */
+
+#include <linux/dsa/an8855.h>
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* AN8855 permit to access the internal GPHY via the PBUS
+ * interface.
+ *
+ * Some piece of this comes from Reverse-Enginnering
+ * by applying the value on the Switch and observing
+ * it by reading the raw value on the MDIO BUS.
+ *
+ * The CL22 address are shifted by 4 left
+ * The CL44 address need to be multiplied by 4 (and
+ * no shift)
+ *
+ * The GPHY have additional configuration (like auto
+ * downshift) at PAGE 1 in the EXT register.
+ * It was discovered that it's possible to access
+ * PAGE x address by increasing them by 2 on setting
+ * the value in the related mask.
+ * The PHY have these custom/vendor register
+ * always starting at 0x10.
+ * From MDIO bus, for address 0x0 to 0xf, PHY
+ * always report PAGE 0 values.
+ * From PBUS, on setting the PAGE value, 0x0 to 0xf
+ * always report 0.
+ *
+ * (it can also be notice that PBUS does NOT change the
+ *  page on accessing these custom/vendor register)
+ *
+ * Comparison examples:
+ *	(PORT 0 PAGE 1)		  |	(PORT 0 PAGE 2)
+ *  PBUS ADDR	  VALUE	    MDIO  |  PBUS ADDR	  VALUE	    MDIO
+ * 0xa0803000: 0x00000000  0x1840 | 0xa0804000: 0x00000000  0x1840
+ * 0xa0803010: 0x00000000  0x7949 | 0xa0804010: 0x00000000  0x7949
+ * 0xa0803020: 0x00000000  0xc0ff | 0xa0804020: 0x00000000  0xc0ff
+ * 0xa0803030: 0x00000000  0x0410 | 0xa0804030: 0x00000000  0x0410
+ * 0xa0803040: 0x00000000  0x0de1 | 0xa0804040: 0x00000000  0x0de1
+ * 0xa0803050: 0x00000000  0x0000 | 0xa0804050: 0x00000000  0x0000
+ * 0xa0803060: 0x00000000  0x0004 | 0xa0804060: 0x00000000  0x0004
+ * 0xa0803070: 0x00000000  0x2001 | 0xa0804070: 0x00000000  0x2001
+ * 0xa0803080: 0x00000000  0x0000 | 0xa0804080: 0x00000000  0x0000
+ * 0xa0803090: 0x00000000  0x0200 | 0xa0804090: 0x00000000  0x0200
+ * 0xa08030a0: 0x00000000  0x4000 | 0xa08040a0: 0x00000000  0x4000
+ * 0xa08030b0: 0x00000000  0x0000 | 0xa08040b0: 0x00000000  0x0000
+ * 0xa08030c0: 0x00000000  0x0000 | 0xa08040c0: 0x00000000  0x0000
+ * 0xa08030d0: 0x00000000  0x0000 | 0xa08040d0: 0x00000000  0x0000
+ * 0xa08030e0: 0x00000000  0x0000 | 0xa08040e0: 0x00000000  0x0000
+ * 0xa08030f0: 0x00000000  0x2000 | 0xa08040f0: 0x00000000  0x2000
+ * 0xa0803100: 0x00000000  0x0000 | 0xa0804100: 0x00000000  0x0000
+ * 0xa0803110: 0x00000000  0x0000 | 0xa0804110: 0x0000030f  0x030f
+ * 0xa0803120: 0x00000000  0x0000 | 0xa0804120: 0x00000000  0x0000
+ * 0xa0803130: 0x00000030  0x0030 | 0xa0804130: 0x00000000  0x0000
+ * 0xa0803140: 0x00003a14  0x3a14 | 0xa0804140: 0x00000000  0x0000
+ * 0xa0803150: 0x00000101  0x0101 | 0xa0804150: 0x00000000  0x0000
+ * 0xa0803160: 0x00000001  0x0001 | 0xa0804160: 0x00000000  0x0000
+ * 0xa0803170: 0x00000800  0x0800 | 0xa0804170: 0x000001ff  0x01ff
+ * 0xa0803180: 0x00000000  0x0000 | 0xa0804180: 0x0000ff1f  0xff1f
+ * 0xa0803190: 0x0000001f  0x001f | 0xa0804190: 0x000083ff  0x83ff
+ * 0xa08031a0: 0x00000000  0x0000 | 0xa08041a0: 0x00000000  0x0000
+ * 0xa08031b0: 0x00000000  0x0000 | 0xa08041b0: 0x00000000  0x0000
+ * 0xa08031c0: 0x00003001  0x3001 | 0xa08041c0: 0x00000000  0x0000
+ * 0xa08031d0: 0x00000000  0x0000 | 0xa08041d0: 0x00000000  0x0000
+ * 0xa08031e0: 0x00000000  0x0000 | 0xa08041e0: 0x00000000  0x0000
+ * 0xa08031f0: 0x00000000  0x0001 | 0xa08041f0: 0x00000000  0x0002
+ *
+ * Using the PBUS permits to have consistent access
+ * to Switch and PHY without having to relay on checking
+ * pages.
+ *
+ * It does also permit to cut on CL45 access and PAGE1
+ * access as the PBUS expose direct register for them.
+ *
+ * The base address is 0xa0800000 and can be seen as
+ * bitmap to derive each specific address.
+ *
+ * Example:
+ *   PORT 1 ADDR 0x2 --> 0xa1800020
+ *			    ^    ^
+ *			    |    ADDR
+ *			    PORT
+ *   PORT 2 DEVAD 1 ADDR 0x2 --> 0xa2840008
+ *				    ^ ^   ^
+ *				    | |   ADDR (*4)
+ *				    | DEVAD
+ *				    PORT
+ *   PORT 3 PAGE 1 ADDR 0x14 --> 0xa3803140
+ *				    ^  ^^^
+ *				    |  |ADDR
+ *				    |  PAGE (+2)
+ *				    PORT
+ *
+ * It's worth mention that trying to read more than the
+ * expected PHY address cause the PBUS to ""crash"" and
+ * the Switch to lock out (requiring a reset).
+ * Validation of the port value is put to prevent this
+ * problem.
+ */
+
+struct an8855_mdio_priv {
+	struct regmap *regmap;
+	u32 base_addr;
+	u8 next_page;
+};
+
+static int an8855_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+	struct an8855_mdio_priv *priv = bus->priv;
+	u32 pbus_addr = AN8855_GPHY_ACCESS;
+	u32 port = addr - priv->base_addr;
+	u32 val;
+	int ret;
+
+	/* Signal invalid address for mdio tools */
+	if (port >= AN8855_NUM_PHY_PORT)
+		return 0xffff;
+
+	pbus_addr |= FIELD_PREP(AN8855_GPHY_PORT, port);
+	pbus_addr |= FIELD_PREP(AN8855_CL22_ADDR, regnum);
+	if (priv->next_page)
+		pbus_addr |= FIELD_PREP(AN8855_PAGE_SELECT,
+					priv->next_page + 2);
+
+	ret = regmap_read(priv->regmap, pbus_addr, &val);
+	if (ret)
+		return ret;
+
+	return val & 0xffff;
+}
+
+static int an8855_mdio_write(struct mii_bus *bus, int addr, int regnum,
+			     u16 value)
+{
+	struct an8855_mdio_priv *priv = bus->priv;
+	u32 pbus_addr = AN8855_GPHY_ACCESS;
+	u32 port = addr - priv->base_addr;
+
+	if (port >= AN8855_NUM_PHY_PORT)
+		return -EINVAL;
+
+	/* When PHY ask to change page, skip writing it and
+	 * save it for the next read/write.
+	 */
+	if (regnum == AN8855_PHY_SELECT_PAGE) {
+		priv->next_page = value;
+		return 0;
+	}
+
+	pbus_addr |= FIELD_PREP(AN8855_GPHY_PORT, port);
+	pbus_addr |= FIELD_PREP(AN8855_CL22_ADDR, regnum);
+	if (priv->next_page)
+		pbus_addr |= FIELD_PREP(AN8855_PAGE_SELECT,
+					priv->next_page + 2);
+
+	return regmap_write(priv->regmap, pbus_addr, value);
+}
+
+static int an8855_mdio_cl45_read(struct mii_bus *bus, int addr, int devnum,
+				 int regnum)
+{
+	struct an8855_mdio_priv *priv = bus->priv;
+	u32 pbus_addr = AN8855_GPHY_ACCESS;
+	u32 port = addr - priv->base_addr;
+	u32 val;
+	int ret;
+
+	/* Signal invalid address for mdio tools */
+	if (port >= AN8855_NUM_PHY_PORT)
+		return 0xffff;
+
+	pbus_addr |= FIELD_PREP(AN8855_GPHY_PORT, port);
+	pbus_addr |= FIELD_PREP(AN8855_DEVAD_ADDR, devnum);
+	pbus_addr |= FIELD_PREP(AN8855_CL45_ADDR, regnum * 4);
+
+	ret = regmap_read(priv->regmap, pbus_addr, &val);
+	if (ret)
+		return ret;
+
+	return val & 0xffff;
+}
+
+static int an8855_mdio_cl45_write(struct mii_bus *bus, int addr, int devnum,
+				  int regnum, u16 value)
+{
+	struct an8855_mdio_priv *priv = bus->priv;
+	u32 pbus_addr = AN8855_GPHY_ACCESS;
+	u32 port = addr - priv->base_addr;
+
+	if (port >= AN8855_NUM_PHY_PORT)
+		return -EINVAL;
+
+	pbus_addr |= FIELD_PREP(AN8855_GPHY_PORT, port);
+	pbus_addr |= FIELD_PREP(AN8855_DEVAD_ADDR, devnum);
+	pbus_addr |= FIELD_PREP(AN8855_CL45_ADDR, regnum * 4);
+
+	return regmap_write(priv->regmap, pbus_addr, value);
+}
+
+static int an8855_mdio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct an8855_mdio_priv *priv;
+	struct mii_bus *bus;
+	int ret;
+
+	bus = devm_mdiobus_alloc_size(dev, sizeof(*priv));
+	if (!bus)
+		return -ENOMEM;
+
+	priv = bus->priv;
+	priv->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!priv->regmap)
+		return -ENOENT;
+
+	ret = of_property_read_u32(dev->parent->of_node, "reg",
+				   &priv->base_addr);
+	if (ret)
+		return -EINVAL;
+
+	bus->name = "an8855_mdio_bus";
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-gphy-pbus", dev_name(dev));
+	bus->parent = dev;
+	bus->read = an8855_mdio_read;
+	bus->write = an8855_mdio_write;
+	bus->read_c45 = an8855_mdio_cl45_read;
+	bus->write_c45 = an8855_mdio_cl45_write;
+
+	ret = devm_of_mdiobus_register(dev, bus, dev->of_node);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to register MDIO bus\n");
+
+	return 0;
+}
+
+static const struct of_device_id an8855_mdio_of_match[] = {
+	{ .compatible = "airoha,an8855-mdio", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_mdio_of_match);
+
+static struct platform_driver an8855_mdio_driver = {
+	.probe	= an8855_mdio_probe,
+	.driver = {
+		.name = "an8855-mdio",
+		.of_match_table = an8855_mdio_of_match,
+	},
+};
+module_platform_driver(an8855_mdio_driver);
+
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for AN8855 MDIO passthrough");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/dsa/an8855.h b/include/linux/dsa/an8855.h
new file mode 100644
index 000000000000..32ec29b3abb0
--- /dev/null
+++ b/include/linux/dsa/an8855.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _NET_AN8855_H
+#define _NET_AN8855_H
+
+#define AN8855_GPHY_ACCESS		0xa0800000
+#define	  AN8855_GPHY_PORT		GENMASK(26, 24)
+#define	  AN8855_DEVAD_ADDR		GENMASK(23, 18)
+#define	  AN8855_PAGE_SELECT		GENMASK(14, 12)
+#define	  AN8855_ADDR			GENMASK(11, 0)
+#define	    AN8855_CL45_ADDR		AN8855_ADDR
+#define	    AN8855_CL22_ADDR		GENMASK(8, 4)
+
+#define AN8855_PHY_SELECT_PAGE		0x1f
+
+#define AN8855_NUM_PHY_PORT		5
+
+#endif /* _NET_AN8855_H */
-- 
2.48.1

[net-next PATCH v15 07/12] nvmem: an8855: Add support for Airoha AN8855 Switch EFUSE

[Christian Marangi]

Add support for Airoha AN8855 Switch EFUSE. These EFUSE might be used
for calibration data for the internal switch PHYs.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/nvmem/Kconfig        | 11 ++++++
 drivers/nvmem/Makefile       |  2 ++
 drivers/nvmem/an8855-efuse.c | 68 ++++++++++++++++++++++++++++++++++++
 3 files changed, 81 insertions(+)
 create mode 100644 drivers/nvmem/an8855-efuse.c

diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
index d370b2ad11e7..8fb1a0efd431 100644
--- a/drivers/nvmem/Kconfig
+++ b/drivers/nvmem/Kconfig
@@ -28,6 +28,17 @@ source "drivers/nvmem/layouts/Kconfig"
 
 # Devices
 
+config NVMEM_AN8855_EFUSE
+	tristate "Airoha AN8855 eFuse support"
+	depends on MFD_AIROHA_AN8855 || COMPILE_TEST
+	help
+	  Say y here to enable support for reading eFuses on Airoha AN8855
+	  Switch. These are e.g. used to store factory programmed
+	  calibration data required for the PHY.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called nvmem-an8855-efuse.
+
 config NVMEM_APPLE_EFUSES
 	tristate "Apple eFuse support"
 	depends on ARCH_APPLE || COMPILE_TEST
diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
index 2021d59688db..5c9e6e450181 100644
--- a/drivers/nvmem/Makefile
+++ b/drivers/nvmem/Makefile
@@ -10,6 +10,8 @@ nvmem_layouts-y			:= layouts.o
 obj-y				+= layouts/
 
 # Devices
+obj-$(CONFIG_NVMEM_AN8855_EFUSE)	+= nvmem-an8855-efuse.o
+nvmem-an8855-efuse-y 			:= an8855-efuse.o
 obj-$(CONFIG_NVMEM_APPLE_EFUSES)	+= nvmem-apple-efuses.o
 nvmem-apple-efuses-y 			:= apple-efuses.o
 obj-$(CONFIG_NVMEM_APPLE_SPMI)		+= apple_nvmem_spmi.o
diff --git a/drivers/nvmem/an8855-efuse.c b/drivers/nvmem/an8855-efuse.c
new file mode 100644
index 000000000000..d1afde6f623f
--- /dev/null
+++ b/drivers/nvmem/an8855-efuse.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Airoha AN8855 Switch EFUSE Driver
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define AN8855_EFUSE_CELL		50
+
+#define AN8855_EFUSE_DATA0		0x1000a500
+#define   AN8855_EFUSE_R50O		GENMASK(30, 24)
+
+static int an8855_efuse_read(void *context, unsigned int offset,
+			     void *val, size_t bytes)
+{
+	struct regmap *regmap = context;
+
+	return regmap_bulk_read(regmap, AN8855_EFUSE_DATA0 + offset,
+				val, bytes / sizeof(u32));
+}
+
+static int an8855_efuse_probe(struct platform_device *pdev)
+{
+	struct nvmem_config an8855_nvmem_config = {
+		.name = "an8855-efuse",
+		.size = AN8855_EFUSE_CELL * sizeof(u32),
+		.stride = sizeof(u32),
+		.word_size = sizeof(u32),
+		.reg_read = an8855_efuse_read,
+	};
+	struct device *dev = &pdev->dev;
+	struct nvmem_device *nvmem;
+	struct regmap *regmap;
+
+	/* Assign NVMEM priv to MFD regmap */
+	regmap = dev_get_regmap(dev->parent, NULL);
+	if (!regmap)
+		return -ENOENT;
+
+	an8855_nvmem_config.priv = regmap;
+	an8855_nvmem_config.dev = dev;
+	nvmem = devm_nvmem_register(dev, &an8855_nvmem_config);
+
+	return PTR_ERR_OR_ZERO(nvmem);
+}
+
+static const struct of_device_id an8855_efuse_of_match[] = {
+	{ .compatible = "airoha,an8855-efuse", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_efuse_of_match);
+
+static struct platform_driver an8855_efuse_driver = {
+	.probe = an8855_efuse_probe,
+	.driver = {
+		.name = "an8855-efuse",
+		.of_match_table = an8855_efuse_of_match,
+	},
+};
+module_platform_driver(an8855_efuse_driver);
+
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for AN8855 Switch EFUSE");
+MODULE_LICENSE("GPL");
-- 
2.48.1

[net-next PATCH v15 08/12] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver

[Christian Marangi]

Add Airoha AN8855 5-Port Gigabit DSA switch. Switch can support
10M, 100M, 1Gb, 2.5G and 5G Ethernet Speed but 5G is currently error out
as it's not currently supported as requires additional configuration for
the PCS.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/dsa/Kconfig  |    9 +
 drivers/net/dsa/Makefile |    1 +
 drivers/net/dsa/an8855.c | 2386 ++++++++++++++++++++++++++++++++++++++
 drivers/net/dsa/an8855.h |  773 ++++++++++++
 4 files changed, 3169 insertions(+)
 create mode 100644 drivers/net/dsa/an8855.c
 create mode 100644 drivers/net/dsa/an8855.h

diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index bb9812b3b0e8..5b02f0d74af3 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -24,6 +24,15 @@ config NET_DSA_LOOP
 	  This enables support for a fake mock-up switch chip which
 	  exercises the DSA APIs.
 
+config NET_DSA_AN8855
+	tristate "Airoha AN8855 Ethernet switch support"
+	depends on MFD_AIROHA_AN8855 || COMPILE_TEST
+	depends on NET_DSA
+	select NET_DSA_TAG_MTK
+	help
+	  This enables support for the Ethernet switch inside the
+	  Airoha AN8855 chip.
+
 source "drivers/net/dsa/hirschmann/Kconfig"
 
 config NET_DSA_LANTIQ_GSWIP
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index cb9a97340e58..a74afb41a491 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_NET_DSA_LOOP)	+= dsa_loop.o
 ifdef CONFIG_NET_DSA_LOOP
 obj-$(CONFIG_FIXED_PHY)		+= dsa_loop_bdinfo.o
 endif
+obj-$(CONFIG_NET_DSA_AN8855)	+= an8855.o
 obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
 obj-$(CONFIG_NET_DSA_MT7530)	+= mt7530.o
 obj-$(CONFIG_NET_DSA_MT7530_MDIO) += mt7530-mdio.o
diff --git a/drivers/net/dsa/an8855.c b/drivers/net/dsa/an8855.c
new file mode 100644
index 000000000000..3cc757f45917
--- /dev/null
+++ b/drivers/net/dsa/an8855.c
@@ -0,0 +1,2386 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Airoha AN8855 DSA Switch driver
+ * Copyright (C) 2023 Min Yao <min.yao@airoha.com>
+ * Copyright (C) 2024 Christian Marangi <ansuelsmth@gmail.com>
+ */
+#include <linux/bitfield.h>
+#include <linux/ethtool.h>
+#include <linux/etherdevice.h>
+#include <linux/if_bridge.h>
+#include <linux/iopoll.h>
+#include <linux/netdevice.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phylink.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <net/dsa.h>
+
+#include "an8855.h"
+
+static const struct an8855_mib_desc an8855_mib[] = {
+	MIB_DESC(1, AN8855_PORT_MIB_TX_DROP, "TxDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_TX_CRC_ERR, "TxCrcErr"),
+	MIB_DESC(1, AN8855_PORT_MIB_TX_COLLISION, "TxCollision"),
+	MIB_DESC(1, AN8855_PORT_MIB_TX_OVERSIZE_DROP, "TxOversizeDrop"),
+	MIB_DESC(2, AN8855_PORT_MIB_TX_BAD_PKT_BYTES, "TxBadPktBytes"),
+	MIB_DESC(1, AN8855_PORT_MIB_RX_DROP, "RxDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_RX_FILTERING, "RxFiltering"),
+	MIB_DESC(1, AN8855_PORT_MIB_RX_CRC_ERR, "RxCrcErr"),
+	MIB_DESC(1, AN8855_PORT_MIB_RX_CTRL_DROP, "RxCtrlDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_RX_INGRESS_DROP, "RxIngressDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_RX_ARL_DROP, "RxArlDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_FLOW_CONTROL_DROP, "FlowControlDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_WRED_DROP, "WredDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_MIRROR_DROP, "MirrorDrop"),
+	MIB_DESC(2, AN8855_PORT_MIB_RX_BAD_PKT_BYTES, "RxBadPktBytes"),
+	MIB_DESC(1, AN8855_PORT_MIB_RXS_FLOW_SAMPLING_PKT_DROP, "RxsFlowSamplingPktDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_RXS_FLOW_TOTAL_PKT_DROP, "RxsFlowTotalPktDrop"),
+	MIB_DESC(1, AN8855_PORT_MIB_PORT_CONTROL_DROP, "PortControlDrop"),
+};
+
+static int
+an8855_mib_init(struct an8855_priv *priv)
+{
+	int ret;
+
+	ret = regmap_write(priv->regmap, AN8855_MIB_CCR,
+			   AN8855_CCR_MIB_ENABLE);
+	if (ret)
+		return ret;
+
+	return regmap_write(priv->regmap, AN8855_MIB_CCR,
+			    AN8855_CCR_MIB_ACTIVATE);
+}
+
+static void an8855_fdb_write(struct an8855_priv *priv, u16 vid,
+			     u8 port_mask, const u8 *mac,
+			     bool add) __must_hold(&priv->reg_mutex)
+{
+	u32 mac_reg[2] = { };
+	u32 reg;
+	int ret;
+
+	mac_reg[0] |= FIELD_PREP(AN8855_ATA1_MAC0, mac[0]);
+	mac_reg[0] |= FIELD_PREP(AN8855_ATA1_MAC1, mac[1]);
+	mac_reg[0] |= FIELD_PREP(AN8855_ATA1_MAC2, mac[2]);
+	mac_reg[0] |= FIELD_PREP(AN8855_ATA1_MAC3, mac[3]);
+	mac_reg[1] |= FIELD_PREP(AN8855_ATA2_MAC4, mac[4]);
+	mac_reg[1] |= FIELD_PREP(AN8855_ATA2_MAC5, mac[5]);
+
+	ret = regmap_bulk_write(priv->regmap, AN8855_ATA1, mac_reg,
+				ARRAY_SIZE(mac_reg));
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to write FDB entry: %d\n", ret);
+		return;
+	}
+
+	reg = AN8855_ATWD_IVL;
+	if (add)
+		reg |= AN8855_ATWD_VLD;
+	reg |= FIELD_PREP(AN8855_ATWD_VID, vid);
+	reg |= FIELD_PREP(AN8855_ATWD_FID, AN8855_FID_BRIDGED);
+	ret = regmap_write(priv->regmap, AN8855_ATWD, reg);
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to write ATWD entry: %d\n", ret);
+		return;
+	}
+	ret = regmap_write(priv->regmap, AN8855_ATWD2,
+			   FIELD_PREP(AN8855_ATWD2_PORT, port_mask));
+	if (ret)
+		dev_err(priv->ds->dev, "failed to write ATWD2 entry: %d\n", ret);
+}
+
+static void an8855_fdb_read(struct an8855_priv *priv, struct an8855_fdb *fdb)
+{
+	u32 reg[4];
+	int ret;
+
+	ret = regmap_bulk_read(priv->regmap, AN8855_ATRD0, reg,
+			       ARRAY_SIZE(reg));
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to read FDB entry: %d\n", ret);
+		return;
+	}
+
+	fdb->live = FIELD_GET(AN8855_ATRD0_LIVE, reg[0]);
+	fdb->type = FIELD_GET(AN8855_ATRD0_TYPE, reg[0]);
+	fdb->ivl = FIELD_GET(AN8855_ATRD0_IVL, reg[0]);
+	fdb->vid = FIELD_GET(AN8855_ATRD0_VID, reg[0]);
+	fdb->fid = FIELD_GET(AN8855_ATRD0_FID, reg[0]);
+	fdb->aging = FIELD_GET(AN8855_ATRD1_AGING, reg[1]);
+	fdb->port_mask = FIELD_GET(AN8855_ATRD3_PORTMASK, reg[3]);
+	fdb->mac[0] = FIELD_GET(AN8855_ATRD2_MAC0, reg[2]);
+	fdb->mac[1] = FIELD_GET(AN8855_ATRD2_MAC1, reg[2]);
+	fdb->mac[2] = FIELD_GET(AN8855_ATRD2_MAC2, reg[2]);
+	fdb->mac[3] = FIELD_GET(AN8855_ATRD2_MAC3, reg[2]);
+	fdb->mac[4] = FIELD_GET(AN8855_ATRD1_MAC4, reg[1]);
+	fdb->mac[5] = FIELD_GET(AN8855_ATRD1_MAC5, reg[1]);
+	fdb->noarp = !!FIELD_GET(AN8855_ATRD0_ARP, reg[0]);
+}
+
+static int an8855_fdb_cmd(struct an8855_priv *priv, u32 cmd,
+			  u32 *rsp) __must_hold(&priv->reg_mutex)
+{
+	u32 val;
+	int ret;
+
+	/* Set the command operating upon the MAC address entries */
+	val = AN8855_ATC_BUSY | cmd;
+	ret = regmap_write(priv->regmap, AN8855_ATC, val);
+	if (ret)
+		return ret;
+
+	ret = regmap_read_poll_timeout(priv->regmap, AN8855_ATC, val,
+				       !(val & AN8855_ATC_BUSY), 20, 200000);
+	if (ret)
+		return ret;
+
+	if (rsp)
+		*rsp = val;
+
+	return 0;
+}
+
+static void
+an8855_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
+{
+	struct dsa_port *dp = dsa_to_port(ds, port);
+	struct an8855_priv *priv = ds->priv;
+	bool learning = false;
+	u32 stp_state;
+	int ret;
+
+	switch (state) {
+	case BR_STATE_DISABLED:
+		stp_state = AN8855_STP_DISABLED;
+		break;
+	case BR_STATE_BLOCKING:
+		stp_state = AN8855_STP_BLOCKING;
+		break;
+	case BR_STATE_LISTENING:
+		stp_state = AN8855_STP_LISTENING;
+		break;
+	case BR_STATE_LEARNING:
+		stp_state = AN8855_STP_LEARNING;
+		learning = dp->learning;
+		break;
+	case BR_STATE_FORWARDING:
+		learning = dp->learning;
+		fallthrough;
+	default:
+		stp_state = AN8855_STP_FORWARDING;
+		break;
+	}
+
+	ret = regmap_update_bits(priv->regmap, AN8855_SSP_P(port),
+				 AN8855_FID_PST_MASK(AN8855_FID_BRIDGED),
+				 AN8855_FID_PST_VAL(AN8855_FID_BRIDGED, stp_state));
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to update SSP reg: %d\n", ret);
+		return;
+	}
+
+	ret = regmap_update_bits(priv->regmap, AN8855_PSC_P(port), AN8855_SA_DIS,
+				 learning ? 0 : AN8855_SA_DIS);
+	if (ret)
+		dev_err(priv->ds->dev, "failed to update learn reg: %d\n", ret);
+}
+
+static void an8855_port_fast_age(struct dsa_switch *ds, int port)
+{
+	struct an8855_priv *priv = ds->priv;
+	int ret;
+
+	/* Set to clean Dynamic entry */
+	ret = regmap_write(priv->regmap, AN8855_ATA2, AN8855_ATA2_TYPE);
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to update ATA2 reg: %d\n", ret);
+		return;
+	}
+
+	/* Set Port */
+	ret = regmap_write(priv->regmap, AN8855_ATWD2,
+			   FIELD_PREP(AN8855_ATWD2_PORT, BIT(port)));
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to update ATWD2 reg: %d\n", ret);
+		return;
+	}
+
+	/* Flush Dynamic entry at port */
+	ret = an8855_fdb_cmd(priv, AN8855_ATC_MAT(AND8855_FDB_MAT_MAC_TYPE_PORT) |
+			     AN8855_FDB_FLUSH, NULL);
+	if (ret)
+		dev_err(priv->ds->dev, "failed to send FDB cmd: %d\n", ret);
+}
+
+static int an8855_update_port_member(struct dsa_switch *ds, int port,
+				     const struct net_device *bridge_dev,
+				     bool join)
+{
+	struct an8855_priv *priv = ds->priv;
+	bool isolated, other_isolated;
+	struct dsa_port *dp;
+	u32 port_mask = 0;
+	int ret;
+
+	isolated = !!(priv->port_isolated_map & BIT(port));
+
+	dsa_switch_for_each_user_port(dp, ds) {
+		if (dp->index == port)
+			continue;
+
+		if (!dsa_port_offloads_bridge_dev(dp, bridge_dev))
+			continue;
+
+		other_isolated = !!(priv->port_isolated_map & BIT(dp->index));
+		port_mask |= BIT(dp->index);
+		/* Add/remove this port to the portvlan mask of the other
+		 * ports in the bridge
+		 */
+		if (join && !(isolated && other_isolated))
+			ret = regmap_set_bits(priv->regmap,
+					      AN8855_PORTMATRIX_P(dp->index),
+					      FIELD_PREP(AN8855_USER_PORTMATRIX,
+							 BIT(port)));
+		else
+			ret = regmap_clear_bits(priv->regmap,
+						AN8855_PORTMATRIX_P(dp->index),
+						FIELD_PREP(AN8855_USER_PORTMATRIX,
+							   BIT(port)));
+		if (ret)
+			return ret;
+	}
+
+	/* Add/remove all other ports to this port's portvlan mask */
+	return regmap_update_bits(priv->regmap, AN8855_PORTMATRIX_P(port),
+				  AN8855_USER_PORTMATRIX,
+				  join ? port_mask : ~port_mask);
+}
+
+static int an8855_port_pre_bridge_flags(struct dsa_switch *ds, int port,
+					struct switchdev_brport_flags flags,
+					struct netlink_ext_ack *extack)
+{
+	if (flags.mask & ~(BR_LEARNING | BR_FLOOD | BR_MCAST_FLOOD |
+			   BR_BCAST_FLOOD | BR_ISOLATED))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int an8855_port_bridge_flags(struct dsa_switch *ds, int port,
+				    struct switchdev_brport_flags flags,
+				    struct netlink_ext_ack *extack)
+{
+	struct an8855_priv *priv = ds->priv;
+	int ret;
+
+	if (flags.mask & BR_LEARNING) {
+		ret = regmap_update_bits(priv->regmap, AN8855_PSC_P(port), AN8855_SA_DIS,
+					 flags.val & BR_LEARNING ? 0 : AN8855_SA_DIS);
+		if (ret)
+			return ret;
+	}
+
+	if (flags.mask & BR_FLOOD) {
+		ret = regmap_update_bits(priv->regmap, AN8855_UNUF, BIT(port),
+					 flags.val & BR_FLOOD ? BIT(port) : 0);
+		if (ret)
+			return ret;
+	}
+
+	if (flags.mask & BR_MCAST_FLOOD) {
+		ret = regmap_update_bits(priv->regmap, AN8855_UNMF, BIT(port),
+					 flags.val & BR_MCAST_FLOOD ? BIT(port) : 0);
+		if (ret)
+			return ret;
+
+		ret = regmap_update_bits(priv->regmap, AN8855_UNIPMF, BIT(port),
+					 flags.val & BR_MCAST_FLOOD ? BIT(port) : 0);
+		if (ret)
+			return ret;
+	}
+
+	if (flags.mask & BR_BCAST_FLOOD) {
+		ret = regmap_update_bits(priv->regmap, AN8855_BCF, BIT(port),
+					 flags.val & BR_BCAST_FLOOD ? BIT(port) : 0);
+		if (ret)
+			return ret;
+	}
+
+	if (flags.mask & BR_ISOLATED) {
+		struct dsa_port *dp = dsa_to_port(ds, port);
+		struct net_device *bridge_dev = dsa_port_bridge_dev_get(dp);
+
+		if (flags.val & BR_ISOLATED)
+			priv->port_isolated_map |= BIT(port);
+		else
+			priv->port_isolated_map &= ~BIT(port);
+
+		ret = an8855_update_port_member(ds, port, bridge_dev, true);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int an8855_set_ageing_time(struct dsa_switch *ds, unsigned int msecs)
+{
+	struct an8855_priv *priv = ds->priv;
+	u32 age_count, age_unit, val;
+
+	/* Convert msec in AN8855_L2_AGING_MS_CONSTANT counter */
+	val = msecs / AN8855_L2_AGING_MS_CONSTANT;
+	/* Derive the count unit */
+	age_unit = val / FIELD_MAX(AN8855_AGE_UNIT);
+	/* Get the count in unit, age_unit is always incremented by 1 internally */
+	age_count = val / (age_unit + 1);
+
+	return regmap_update_bits(priv->regmap, AN8855_AAC,
+				  AN8855_AGE_CNT | AN8855_AGE_UNIT,
+				  FIELD_PREP(AN8855_AGE_CNT, age_count) |
+				  FIELD_PREP(AN8855_AGE_UNIT, age_unit));
+}
+
+static int an8855_port_bridge_join(struct dsa_switch *ds, int port,
+				   struct dsa_bridge bridge,
+				   bool *tx_fwd_offload,
+				   struct netlink_ext_ack *extack)
+{
+	struct an8855_priv *priv = ds->priv;
+	int ret;
+
+	ret = an8855_update_port_member(ds, port, bridge.dev, true);
+	if (ret)
+		return ret;
+
+	/* Set to fallback mode for independent VLAN learning if in a bridge */
+	return regmap_update_bits(priv->regmap, AN8855_PCR_P(port),
+				  AN8855_PORT_VLAN,
+				  FIELD_PREP(AN8855_PORT_VLAN,
+					     AN8855_PORT_FALLBACK_MODE));
+}
+
+static void an8855_port_bridge_leave(struct dsa_switch *ds, int port,
+				     struct dsa_bridge bridge)
+{
+	struct an8855_priv *priv = ds->priv;
+	int ret;
+
+	ret = an8855_update_port_member(ds, port, bridge.dev, false);
+	if (ret) {
+		dev_err(priv->ds->dev, "failed to update port member: %d\n", ret);
+		return;
+	}
+
+	/* When a port is removed from the bridge, the port would be set up
+	 * back to the default as is at initial boot which is a VLAN-unaware
+	 * port.
+	 */
+	ret = regmap_update_bits(priv->regmap, AN8855_PCR_P(port),
+				 AN8855_PORT_VLAN,
+				 FIELD_PREP(AN8855_PORT_VLAN,
+					    AN8855_PORT_MATRIX_MODE));
+	if (ret)
+		dev_err(priv->ds->dev, "failed to update PCR reg: %d\n", ret);
+}
+
+static int an8855_port_fdb_add(struct dsa_switch *ds, int port,
+			       const unsigned char *addr, u16 vid,
+			       struct dsa_db db)
+{
+	struct an8855_priv *priv = ds->priv;
+	u8 port_mask = BIT(port);
+	int ret;
+
+	/* With VLAN-Unaware entry, set vid to default vid */
+	if (!vid)
+		vid = AN8855_PORT_VID_DEFAULT;
+
+	mutex_lock(&priv->reg_mutex);
+	an8855_fdb_write(priv, vid, port_mask, addr, true);
+	ret = an8855_fdb_cmd(priv, AN8855_FDB_WRITE, NULL);
+	mutex_unlock(&priv->reg_mutex);
+
+	return ret;
+}
+
+static int an8855_port_fdb_del(struct dsa_switch *ds, int port,
+			       const unsigned char *addr, u16 vid,
+			       struct dsa_db db)
+{
+	struct an8855_priv *priv = ds->priv;
+	u8 port_mask = BIT(port);
+	int ret;
+
+	/* With VLAN-Unaware entry, set vid to default vid */
+	if (!vid)
+		vid = AN8855_PORT_VID_DEFAULT;
+
+	mutex_lock(&priv->reg_mutex);
+	an8855_fdb_write(priv, vid, port_mask, addr, false);
+	ret = an8855_fdb_cmd(priv, AN8855_FDB_WRITE, NULL);
+	mutex_unlock(&priv->reg_mutex);
+
+	return ret;
+}
+
+static int an8855_port_fdb_dump(struct dsa_switch *ds, int port,
+				dsa_fdb_dump_cb_t *cb, void *data)
+{
+	struct an8855_priv *priv = ds->priv;
+	int banks, count = 0;
+	u32 rsp;
+	int ret;
+	int i;
+
+	mutex_lock(&priv->reg_mutex);
+
+	/* Load search port */
+	ret = regmap_write(priv->regmap, AN8855_ATWD2,
+			   FIELD_PREP(AN8855_ATWD2_PORT, BIT(port)));
+	if (ret)
+		goto exit;
+	ret = an8855_fdb_cmd(priv, AN8855_ATC_MAT(AND8855_FDB_MAT_MAC_PORT) |
+			     AN8855_FDB_START, &rsp);
+	if (ret < 0)
+		goto exit;
+
+	do {
+		/* From response get the number of banks to read, exit if 0 */
+		banks = FIELD_GET(AN8855_ATC_HIT, rsp);
+		if (!banks)
+			break;
+
+		/* Each banks have 4 entry */
+		for (i = 0; i < 4; i++) {
+			struct an8855_fdb _fdb = {  };
+
+			count++;
+
+			/* Check if bank is present */
+			if (!(banks & BIT(i)))
+				continue;
+
+			/* Select bank entry index */
+			ret = regmap_write(priv->regmap, AN8855_ATRDS,
+					   FIELD_PREP(AN8855_ATRD_SEL, i));
+			if (ret)
+				break;
+			/* wait 1ms for the bank entry to be filled */
+			usleep_range(1000, 1500);
+			an8855_fdb_read(priv, &_fdb);
+
+			if (!_fdb.live)
+				continue;
+			ret = cb(_fdb.mac, _fdb.vid, _fdb.noarp, data);
+			if (ret < 0)
+				break;
+		}
+
+		/* Stop if reached max FDB number */
+		if (count >= AN8855_NUM_FDB_RECORDS)
+			break;
+
+		/* Read next bank */
+		ret = an8855_fdb_cmd(priv, AN8855_ATC_MAT(AND8855_FDB_MAT_MAC_PORT) |
+				     AN8855_FDB_NEXT, &rsp);
+		if (ret < 0)
+			break;
+	} while (true);
+
+exit:
+	mutex_unlock(&priv->reg_mutex);
+	return ret;
+}
+
+static int an8855_vlan_cmd(struct an8855_priv *priv, enum an8855_vlan_cmd cmd,
+			   u16 vid) __must_hold(&priv->reg_mutex)
+{
+	u32 val;
+	int ret;
+
+	val = AN8855_VTCR_BUSY | FIELD_PREP(AN8855_VTCR_FUNC, cmd) |
+	      FIELD_PREP(AN8855_VTCR_VID, vid);
+	ret = regmap_write(priv->regmap, AN8855_VTCR, val);
+	if (ret)
+		return ret;
+
+	return regmap_read_poll_timeout(priv->regmap, AN8855_VTCR, val,
+					!(val & AN8855_VTCR_BUSY), 20, 200000);
+}
+
+static int an8855_vlan_add(struct an8855_priv *priv, u8 port, u16 vid,
+			   bool untagged) __must_hold(&priv->reg_mutex)
+{
+	u32 port_mask;
+	u32 val;
+	int ret;
+
+	/* Fetch entry */
+	ret = an8855_vlan_cmd(priv, AN8855_VTCR_RD_VID, vid);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(priv->regmap, AN8855_VARD0, &val);
+	if (ret)
+		return ret;
+	port_mask = FIELD_GET(AN8855_VA0_PORT, val) | BIT(port);
+
+	/* Validate the entry with independent learning, create egress tag per
+	 * VLAN and joining the port as one of the port members.
+	 */
+	val = (val & AN8855_VA0_ETAG) | AN8855_VA0_IVL_MAC |
+	      AN8855_VA0_VTAG_EN | AN8855_VA0_VLAN_VALID |
+	      FIELD_PREP(AN8855_VA0_PORT, port_mask) |
+	      FIELD_PREP(AN8855_VA0_FID, AN8855_FID_BRIDGED);
+	ret = regmap_write(priv->regmap, AN8855_VAWD0, val);
+	if (ret)
+		return ret;
+	ret = regmap_write(priv->regmap, AN8855_VAWD1, 0);
+	if (ret)
+		return ret;
+
+	/* CPU port is always taken as a tagged port for serving more than one
+	 * VLANs across and also being applied with egress type stack mode for
+	 * that VLAN tags would be appended after hardware special tag used as
+	 * DSA tag.
+	 */
+	if (port == AN8855_CPU_PORT)
+		val = AN8855_VLAN_EGRESS_STACK;
+	/* Decide whether adding tag or not for those outgoing packets from the
+	 * port inside the VLAN.
+	 */
+	else
+		val = untagged ? AN8855_VLAN_EGRESS_UNTAG : AN8855_VLAN_EGRESS_TAG;
+	ret = regmap_update_bits(priv->regmap, AN8855_VAWD0,
+				 AN8855_VA0_ETAG_PORT_MASK(port),
+				 AN8855_VA0_ETAG_PORT_VAL(port, val));
+	if (ret)
+		return ret;
+
+	/* Flush result to hardware */
+	return an8855_vlan_cmd(priv, AN8855_VTCR_WR_VID, vid);
+}
+
+static int an8855_vlan_del(struct an8855_priv *priv, u8 port,
+			   u16 vid) __must_hold(&priv->reg_mutex)
+{
+	u32 port_mask;
+	u32 val;
+	int ret;
+
+	/* Fetch entry */
+	ret = an8855_vlan_cmd(priv, AN8855_VTCR_RD_VID, vid);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(priv->regmap, AN8855_VARD0, &val);
+	if (ret)
+		return ret;
+	port_mask = FIELD_GET(AN8855_VA0_PORT, val) & ~BIT(port);
+
+	if (!(val & AN8855_VA0_VLAN_VALID)) {
+		dev_err(priv->ds->dev, "Cannot be deleted due to invalid entry: %d\n", ret);
+		return -EINVAL;
+	}
+
+	if (port_mask) {
+		val = (val & AN8855_VA0_ETAG) | AN8855_VA0_IVL_MAC |
+		       AN8855_VA0_VTAG_EN | AN8855_VA0_VLAN_VALID |
+		       FIELD_PREP(AN8855_VA0_PORT, port_mask);
+		ret = regmap_write(priv->regmap, AN8855_VAWD0, val);
+		if (ret)
+			return ret;
+	} else {
+		ret = regmap_write(priv->regmap, AN8855_VAWD0, 0);
+		if (ret)
+			return ret;
+	}
+	ret = regmap_write(priv->regmap, AN8855_VAWD1, 0);
+	if (ret)
+		return ret;
+
+	/* Flush result to hardware */
+	return an8855_vlan_cmd(priv, AN8855_VTCR_WR_VID, vid);
+}
+
+static int an8855_port_set_vlan_mode(struct an8855_priv *priv, int port,
+				     enum an8855_port_mode port_mode,
+				     enum an8855_vlan_port_eg_tag eg_tag,
+				     enum an8855_vlan_port_attr vlan_attr,
+				     enum an8855_vlan_port_acc_frm acc_frm)
+{
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_PCR_P(port),
+				 AN8855_PORT_VLAN,
+				 FIELD_PREP(AN8855_PORT_VLAN, port_mode));
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(priv->regmap, AN8855_PVC_P(port),
+				  AN8855_PVC_EG_TAG | AN8855_VLAN_ATTR | AN8855_ACC_FRM,
+				  FIELD_PREP(AN8855_PVC_EG_TAG, eg_tag) |
+				  FIELD_PREP(AN8855_VLAN_ATTR, vlan_attr) |
+				  FIELD_PREP(AN8855_ACC_FRM, acc_frm));
+}
+
+static int an8855_port_set_pvid(struct an8855_priv *priv, int port,
+				u16 pvid)
+{
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_PPBV1_P(port),
+				 AN8855_PPBV_G0_PORT_VID,
+				 FIELD_PREP(AN8855_PPBV_G0_PORT_VID, pvid));
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(priv->regmap, AN8855_PVID_P(port),
+				  AN8855_G0_PORT_VID,
+				  FIELD_PREP(AN8855_G0_PORT_VID, pvid));
+}
+
+static int an8855_port_enable_vlan_filtering(struct dsa_switch *ds, int port)
+{
+	struct an8855_priv *priv = ds->priv;
+	u32 acc_frm, val;
+	int ret;
+
+	/* CPU port is set to fallback mode to let untagged
+	 * frames pass through.
+	 */
+	ret = an8855_port_set_vlan_mode(priv, AN8855_CPU_PORT,
+					AN8855_PORT_FALLBACK_MODE,
+					AN8855_VLAN_EG_CONSISTENT,
+					AN8855_VLAN_USER,
+					AN8855_VLAN_ACC_ALL);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(priv->regmap, AN8855_PVID_P(port), &val);
+	if (ret)
+		return ret;
+
+	/* Only accept tagged frames if PVID is not set */
+	if (FIELD_GET(AN8855_G0_PORT_VID, val) != AN8855_PORT_VID_DEFAULT)
+		acc_frm = AN8855_VLAN_ACC_TAGGED;
+	else
+		acc_frm = AN8855_VLAN_ACC_ALL;
+
+	/* Trapped into security mode allows packet forwarding through VLAN
+	 * table lookup.
+	 * Set the port as a user port which is to be able to recognize VID
+	 * from incoming packets before fetching entry within the VLAN table.
+	 */
+	return an8855_port_set_vlan_mode(priv, port,
+					 AN8855_PORT_SECURITY_MODE,
+					 AN8855_VLAN_EG_DISABLED,
+					 AN8855_VLAN_USER,
+					 acc_frm);
+}
+
+static int an8855_port_disable_vlan_filtering(struct dsa_switch *ds, int port)
+{
+	struct an8855_priv *priv = ds->priv;
+	bool disable_cpu_vlan = true;
+	struct dsa_port *dp;
+	u32 port_mode;
+	int ret;
+
+	/* This is called after .port_bridge_leave when leaving a VLAN-aware
+	 * bridge. Don't set standalone ports to fallback mode.
+	 */
+	if (dsa_port_bridge_dev_get(dsa_to_port(ds, port)))
+		port_mode = AN8855_PORT_FALLBACK_MODE;
+	else
+		port_mode = AN8855_PORT_MATRIX_MODE;
+
+	/* When a port is removed from the bridge, the port would be set up
+	 * back to the default as is at initial boot which is a VLAN-unaware
+	 * port.
+	 */
+	ret = an8855_port_set_vlan_mode(priv, port, port_mode,
+					AN8855_VLAN_EG_CONSISTENT,
+					AN8855_VLAN_TRANSPARENT,
+					AN8855_VLAN_ACC_ALL);
+	if (ret)
+		return ret;
+
+	/* Restore default PVID */
+	ret = an8855_port_set_pvid(priv, port, AN8855_PORT_VID_DEFAULT);
+	if (ret)
+		return ret;
+
+	dsa_switch_for_each_user_port(dp, ds) {
+		if (dsa_port_is_vlan_filtering(dp)) {
+			disable_cpu_vlan = false;
+			break;
+		}
+	}
+
+	if (disable_cpu_vlan) {
+		ret = an8855_port_set_vlan_mode(priv, AN8855_CPU_PORT,
+						AN8855_PORT_MATRIX_MODE,
+						AN8855_VLAN_EG_CONSISTENT,
+						AN8855_VLAN_USER,
+						AN8855_VLAN_ACC_ALL);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int an8855_port_vlan_filtering(struct dsa_switch *ds, int port,
+				      bool vlan_filtering,
+				      struct netlink_ext_ack *extack)
+{
+	/* The port is being kept as VLAN-unaware port when bridge is
+	 * set up with vlan_filtering not being set, Otherwise, the
+	 * port and the corresponding CPU port is required the setup
+	 * for becoming a VLAN-aware port.
+	 */
+	if (vlan_filtering)
+		return an8855_port_enable_vlan_filtering(ds, port);
+
+	return an8855_port_disable_vlan_filtering(ds, port);
+}
+
+static int an8855_port_vlan_add(struct dsa_switch *ds, int port,
+				const struct switchdev_obj_port_vlan *vlan,
+				struct netlink_ext_ack *extack)
+{
+	bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+	bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
+	struct an8855_priv *priv = ds->priv;
+	u32 val;
+	int ret;
+
+	mutex_lock(&priv->reg_mutex);
+	ret = an8855_vlan_add(priv, port, vlan->vid, untagged);
+	mutex_unlock(&priv->reg_mutex);
+	if (ret)
+		return ret;
+
+	if (pvid) {
+		/* Accept all frames if PVID is set */
+		regmap_update_bits(priv->regmap, AN8855_PVC_P(port), AN8855_ACC_FRM,
+				   FIELD_PREP(AN8855_ACC_FRM, AN8855_VLAN_ACC_ALL));
+
+		/* Only configure PVID if VLAN filtering is enabled */
+		if (dsa_port_is_vlan_filtering(dsa_to_port(ds, port))) {
+			ret = an8855_port_set_pvid(priv, port, vlan->vid);
+			if (ret)
+				return ret;
+		}
+	} else if (vlan->vid) {
+		ret = regmap_read(priv->regmap, AN8855_PVID_P(port), &val);
+		if (ret)
+			return ret;
+
+		if (FIELD_GET(AN8855_G0_PORT_VID, val) != vlan->vid)
+			return 0;
+
+		/* This VLAN is overwritten without PVID, so unset it */
+		if (dsa_port_is_vlan_filtering(dsa_to_port(ds, port))) {
+			ret = regmap_update_bits(priv->regmap, AN8855_PVC_P(port),
+						 AN8855_ACC_FRM,
+						 FIELD_PREP(AN8855_ACC_FRM,
+							    AN8855_VLAN_ACC_TAGGED));
+			if (ret)
+				return ret;
+		}
+
+		ret = an8855_port_set_pvid(priv, port, AN8855_PORT_VID_DEFAULT);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int an8855_port_vlan_del(struct dsa_switch *ds, int port,
+				const struct switchdev_obj_port_vlan *vlan)
+{
+	struct an8855_priv *priv = ds->priv;
+	u32 val;
+	int ret;
+
+	mutex_lock(&priv->reg_mutex);
+	ret = an8855_vlan_del(priv, port, vlan->vid);
+	mutex_unlock(&priv->reg_mutex);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(priv->regmap, AN8855_PVID_P(port), &val);
+	if (ret)
+		return ret;
+
+	/* PVID is being restored to the default whenever the PVID port
+	 * is being removed from the VLAN.
+	 */
+	if (FIELD_GET(AN8855_G0_PORT_VID, val) == vlan->vid) {
+		/* Only accept tagged frames if the port is VLAN-aware */
+		if (dsa_port_is_vlan_filtering(dsa_to_port(ds, port))) {
+			ret = regmap_update_bits(priv->regmap, AN8855_PVC_P(port),
+						 AN8855_ACC_FRM,
+						 FIELD_PREP(AN8855_ACC_FRM,
+							    AN8855_VLAN_ACC_TAGGED));
+			if (ret)
+				return ret;
+		}
+
+		ret = an8855_port_set_pvid(priv, port, AN8855_PORT_VID_DEFAULT);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int an8855_port_mdb_add(struct dsa_switch *ds, int port,
+			       const struct switchdev_obj_port_mdb *mdb,
+			       struct dsa_db db)
+{
+	struct an8855_priv *priv = ds->priv;
+	const u8 *addr = mdb->addr;
+	u16 vid = mdb->vid;
+	u8 port_mask = 0;
+	u32 val;
+	int ret;
+
+	/* With VLAN-Unaware entry, set vid to default vid */
+	if (!vid)
+		vid = AN8855_PORT_VID_DEFAULT;
+
+	mutex_lock(&priv->reg_mutex);
+
+	an8855_fdb_write(priv, vid, 0, addr, false);
+	if (!an8855_fdb_cmd(priv, AN8855_FDB_READ, NULL)) {
+		ret = regmap_read(priv->regmap, AN8855_ATRD3, &val);
+		if (ret)
+			goto exit;
+
+		port_mask = FIELD_GET(AN8855_ATRD3_PORTMASK, val);
+	}
+
+	port_mask |= BIT(port);
+	an8855_fdb_write(priv, vid, port_mask, addr, true);
+	ret = an8855_fdb_cmd(priv, AN8855_FDB_WRITE, NULL);
+
+exit:
+	mutex_unlock(&priv->reg_mutex);
+
+	return ret;
+}
+
+static int an8855_port_mdb_del(struct dsa_switch *ds, int port,
+			       const struct switchdev_obj_port_mdb *mdb,
+			       struct dsa_db db)
+{
+	struct an8855_priv *priv = ds->priv;
+	const u8 *addr = mdb->addr;
+	u16 vid = mdb->vid;
+	u8 port_mask = 0;
+	u32 val;
+	int ret;
+
+	/* With VLAN-Unaware entry, set vid to default vid */
+	if (!vid)
+		vid = AN8855_PORT_VID_DEFAULT;
+
+	mutex_lock(&priv->reg_mutex);
+
+	an8855_fdb_write(priv, vid, 0, addr, 0);
+	if (!an8855_fdb_cmd(priv, AN8855_FDB_READ, NULL)) {
+		ret = regmap_read(priv->regmap, AN8855_ATRD3, &val);
+		if (ret)
+			goto exit;
+
+		port_mask = FIELD_GET(AN8855_ATRD3_PORTMASK, val);
+	}
+
+	port_mask &= ~BIT(port);
+	an8855_fdb_write(priv, vid, port_mask, addr, port_mask ? true : false);
+	ret = an8855_fdb_cmd(priv, AN8855_FDB_WRITE, NULL);
+
+exit:
+	mutex_unlock(&priv->reg_mutex);
+
+	return ret;
+}
+
+static int an8855_port_change_mtu(struct dsa_switch *ds, int port,
+				  int new_mtu)
+{
+	struct an8855_priv *priv = ds->priv;
+	int length;
+	u32 val;
+
+	/* When a new MTU is set, DSA always set the CPU port's MTU to the
+	 * largest MTU of the slave ports. Because the switch only has a global
+	 * RX length register, only allowing CPU port here is enough.
+	 */
+	if (!dsa_is_cpu_port(ds, port))
+		return 0;
+
+	/* RX length also includes Ethernet header, MTK tag, and FCS length */
+	length = new_mtu + ETH_HLEN + MTK_TAG_LEN + ETH_FCS_LEN;
+	if (length <= 1522)
+		val = AN8855_MAX_RX_PKT_1518_1522;
+	else if (length <= 1536)
+		val = AN8855_MAX_RX_PKT_1536;
+	else if (length <= 1552)
+		val = AN8855_MAX_RX_PKT_1552;
+	else if (length <= 3072)
+		val = AN8855_MAX_RX_JUMBO_3K;
+	else if (length <= 4096)
+		val = AN8855_MAX_RX_JUMBO_4K;
+	else if (length <= 5120)
+		val = AN8855_MAX_RX_JUMBO_5K;
+	else if (length <= 6144)
+		val = AN8855_MAX_RX_JUMBO_6K;
+	else if (length <= 7168)
+		val = AN8855_MAX_RX_JUMBO_7K;
+	else if (length <= 8192)
+		val = AN8855_MAX_RX_JUMBO_8K;
+	else if (length <= 9216)
+		val = AN8855_MAX_RX_JUMBO_9K;
+	else if (length <= 12288)
+		val = AN8855_MAX_RX_JUMBO_12K;
+	else if (length <= 15360)
+		val = AN8855_MAX_RX_JUMBO_15K;
+	else
+		val = AN8855_MAX_RX_JUMBO_16K;
+
+	/* Enable JUMBO packet */
+	if (length > 1552)
+		val |= AN8855_MAX_RX_PKT_JUMBO;
+
+	return regmap_update_bits(priv->regmap, AN8855_GMACCR,
+				  AN8855_MAX_RX_JUMBO | AN8855_MAX_RX_PKT_LEN,
+				  val);
+}
+
+static int an8855_port_max_mtu(struct dsa_switch *ds, int port)
+{
+	return AN8855_MAX_MTU;
+}
+
+static void an8855_get_strings(struct dsa_switch *ds, int port,
+			       u32 stringset, uint8_t *data)
+{
+	int i;
+
+	if (stringset != ETH_SS_STATS)
+		return;
+
+	for (i = 0; i < ARRAY_SIZE(an8855_mib); i++)
+		ethtool_puts(&data, an8855_mib[i].name);
+}
+
+static void an8855_read_port_stats(struct an8855_priv *priv, int port,
+				   u32 offset, u8 size, uint64_t *data)
+{
+	u32 val, reg = AN8855_PORT_MIB_COUNTER(port) + offset;
+
+	regmap_read(priv->regmap, reg, &val);
+	*data = val;
+
+	if (size == 2) {
+		regmap_read(priv->regmap, reg + 4, &val);
+		*data |= (u64)val << 32;
+	}
+}
+
+static void an8855_get_ethtool_stats(struct dsa_switch *ds, int port,
+				     uint64_t *data)
+{
+	struct an8855_priv *priv = ds->priv;
+	const struct an8855_mib_desc *mib;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(an8855_mib); i++) {
+		mib = &an8855_mib[i];
+
+		an8855_read_port_stats(priv, port, mib->offset, mib->size,
+				       data + i);
+	}
+}
+
+static int an8855_get_sset_count(struct dsa_switch *ds, int port,
+				 int sset)
+{
+	if (sset != ETH_SS_STATS)
+		return 0;
+
+	return ARRAY_SIZE(an8855_mib);
+}
+
+static void an8855_get_eth_mac_stats(struct dsa_switch *ds, int port,
+				     struct ethtool_eth_mac_stats *mac_stats)
+{
+	struct an8855_priv *priv = ds->priv;
+
+	/* MIB counter doesn't provide a FramesTransmittedOK but instead
+	 * provide stats for Unicast, Broadcast and Multicast frames separately.
+	 * To simulate a global frame counter, read Unicast and addition Multicast
+	 * and Broadcast later
+	 */
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_UNICAST, 1,
+			       &mac_stats->FramesTransmittedOK);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_SINGLE_COLLISION, 1,
+			       &mac_stats->SingleCollisionFrames);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_MULTIPLE_COLLISION, 1,
+			       &mac_stats->MultipleCollisionFrames);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_UNICAST, 1,
+			       &mac_stats->FramesReceivedOK);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_BYTES, 2,
+			       &mac_stats->OctetsTransmittedOK);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_ALIGN_ERR, 1,
+			       &mac_stats->AlignmentErrors);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_DEFERRED, 1,
+			       &mac_stats->FramesWithDeferredXmissions);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_LATE_COLLISION, 1,
+			       &mac_stats->LateCollisions);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_EXCESSIVE_COLLISION, 1,
+			       &mac_stats->FramesAbortedDueToXSColls);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_BYTES, 2,
+			       &mac_stats->OctetsReceivedOK);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_MULTICAST, 1,
+			       &mac_stats->MulticastFramesXmittedOK);
+	mac_stats->FramesTransmittedOK += mac_stats->MulticastFramesXmittedOK;
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_BROADCAST, 1,
+			       &mac_stats->BroadcastFramesXmittedOK);
+	mac_stats->FramesTransmittedOK += mac_stats->BroadcastFramesXmittedOK;
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_MULTICAST, 1,
+			       &mac_stats->MulticastFramesReceivedOK);
+	mac_stats->FramesReceivedOK += mac_stats->MulticastFramesReceivedOK;
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_BROADCAST, 1,
+			       &mac_stats->BroadcastFramesReceivedOK);
+	mac_stats->FramesReceivedOK += mac_stats->BroadcastFramesReceivedOK;
+}
+
+static const struct ethtool_rmon_hist_range an8855_rmon_ranges[] = {
+	{ 0, 64 },
+	{ 65, 127 },
+	{ 128, 255 },
+	{ 256, 511 },
+	{ 512, 1023 },
+	{ 1024, 1518 },
+	{ 1519, AN8855_MAX_MTU },
+	{}
+};
+
+static void an8855_get_rmon_stats(struct dsa_switch *ds, int port,
+				  struct ethtool_rmon_stats *rmon_stats,
+				  const struct ethtool_rmon_hist_range **ranges)
+{
+	struct an8855_priv *priv = ds->priv;
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_UNDER_SIZE_ERR, 1,
+			       &rmon_stats->undersize_pkts);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_OVER_SZ_ERR, 1,
+			       &rmon_stats->oversize_pkts);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_FRAG_ERR, 1,
+			       &rmon_stats->fragments);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_JABBER_ERR, 1,
+			       &rmon_stats->jabbers);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_64, 1,
+			       &rmon_stats->hist[0]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_65_TO_127, 1,
+			       &rmon_stats->hist[1]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_128_TO_255, 1,
+			       &rmon_stats->hist[2]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_256_TO_511, 1,
+			       &rmon_stats->hist[3]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_512_TO_1023, 1,
+			       &rmon_stats->hist[4]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_1024_TO_1518, 1,
+			       &rmon_stats->hist[5]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PKT_SZ_1519_TO_MAX, 1,
+			       &rmon_stats->hist[6]);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_64, 1,
+			       &rmon_stats->hist_tx[0]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_65_TO_127, 1,
+			       &rmon_stats->hist_tx[1]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_128_TO_255, 1,
+			       &rmon_stats->hist_tx[2]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_256_TO_511, 1,
+			       &rmon_stats->hist_tx[3]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_512_TO_1023, 1,
+			       &rmon_stats->hist_tx[4]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_1024_TO_1518, 1,
+			       &rmon_stats->hist_tx[5]);
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PKT_SZ_1519_TO_MAX, 1,
+			       &rmon_stats->hist_tx[6]);
+
+	*ranges = an8855_rmon_ranges;
+}
+
+static void an8855_get_eth_ctrl_stats(struct dsa_switch *ds, int port,
+				      struct ethtool_eth_ctrl_stats *ctrl_stats)
+{
+	struct an8855_priv *priv = ds->priv;
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_TX_PAUSE, 1,
+			       &ctrl_stats->MACControlFramesTransmitted);
+
+	an8855_read_port_stats(priv, port, AN8855_PORT_MIB_RX_PAUSE, 1,
+			       &ctrl_stats->MACControlFramesReceived);
+}
+
+static int an8855_port_mirror_add(struct dsa_switch *ds, int port,
+				  struct dsa_mall_mirror_tc_entry *mirror,
+				  bool ingress,
+				  struct netlink_ext_ack *extack)
+{
+	struct an8855_priv *priv = ds->priv;
+	int monitor_port;
+	u32 val;
+	int ret;
+
+	/* Check for existent entry */
+	if ((ingress ? priv->mirror_rx : priv->mirror_tx) & BIT(port)) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Mirroring already set for port");
+		return -EEXIST;
+	}
+
+	ret = regmap_read(priv->regmap, AN8855_MIR, &val);
+	if (ret)
+		return ret;
+
+	/* AN8855 supports 4 monitor port, but only use first group */
+	monitor_port = FIELD_GET(AN8855_MIRROR_PORT, val);
+	if (val & AN8855_MIRROR_EN && monitor_port != mirror->to_local_port) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Mirror port already set for a different port");
+		return -EEXIST;
+	}
+
+	val = AN8855_MIRROR_EN;
+	val |= FIELD_PREP(AN8855_MIRROR_PORT, mirror->to_local_port);
+	ret = regmap_update_bits(priv->regmap, AN8855_MIR,
+				 AN8855_MIRROR_EN | AN8855_MIRROR_PORT,
+				 val);
+	if (ret)
+		return ret;
+
+	ret = regmap_set_bits(priv->regmap, AN8855_PCR_P(port),
+			      ingress ? AN8855_PORT_RX_MIR : AN8855_PORT_TX_MIR);
+	if (ret)
+		return ret;
+
+	if (ingress)
+		priv->mirror_rx |= BIT(port);
+	else
+		priv->mirror_tx |= BIT(port);
+
+	return 0;
+}
+
+static void an8855_port_mirror_del(struct dsa_switch *ds, int port,
+				   struct dsa_mall_mirror_tc_entry *mirror)
+{
+	struct an8855_priv *priv = ds->priv;
+
+	if (mirror->ingress)
+		priv->mirror_rx &= ~BIT(port);
+	else
+		priv->mirror_tx &= ~BIT(port);
+
+	regmap_clear_bits(priv->regmap, AN8855_PCR_P(port),
+			  mirror->ingress ? AN8855_PORT_RX_MIR :
+					    AN8855_PORT_TX_MIR);
+
+	if (!priv->mirror_rx && !priv->mirror_tx)
+		regmap_clear_bits(priv->regmap, AN8855_MIR, AN8855_MIRROR_EN);
+}
+
+static int an8855_port_enable(struct dsa_switch *ds, int port,
+			      struct phy_device *phy)
+{
+	struct an8855_priv *priv = ds->priv;
+
+	return regmap_set_bits(priv->regmap, AN8855_PMCR_P(port),
+			       AN8855_PMCR_TX_EN | AN8855_PMCR_RX_EN);
+}
+
+static void an8855_port_disable(struct dsa_switch *ds, int port)
+{
+	struct an8855_priv *priv = ds->priv;
+	int ret;
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_PMCR_P(port),
+				AN8855_PMCR_TX_EN | AN8855_PMCR_RX_EN);
+	if (ret)
+		dev_err(priv->ds->dev, "failed to disable port: %d\n", ret);
+}
+
+static int an8855_set_mac_eee(struct dsa_switch *ds, int port,
+			      struct ethtool_keee *e)
+{
+	if (e->tx_lpi_timer > 0xFFF)
+		return -EINVAL;
+
+	return 0;
+}
+
+static enum dsa_tag_protocol an8855_get_tag_protocol(struct dsa_switch *ds,
+						     int port,
+						     enum dsa_tag_protocol mp)
+{
+	return DSA_TAG_PROTO_MTK;
+}
+
+/* Similar to MT7530 also trap link local frame and special frame to CPU */
+static int an8855_trap_special_frames(struct an8855_priv *priv)
+{
+	u32 mask, val;
+	int ret;
+
+	/* Trap BPDUs to the CPU port(s) and egress them
+	 * VLAN-untagged.
+	 */
+	mask = AN8855_BPDU_BPDU_FR | AN8855_BPDU_EG_TAG | AN8855_BPDU_PORT_FW;
+	val = AN8855_BPDU_BPDU_FR |
+	      FIELD_PREP(AN8855_BPDU_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
+	      FIELD_PREP(AN8855_BPDU_PORT_FW, AN8855_BPDU_CPU_ONLY);
+	ret = regmap_update_bits(priv->regmap, AN8855_BPC, mask, val);
+	if (ret)
+		return ret;
+
+	/* Trap 802.1X PAE frames to the CPU port(s) and egress them
+	 * VLAN-untagged.
+	 */
+	mask = AN8855_PAE_BPDU_FR | AN8855_PAE_EG_TAG | AN8855_PAE_PORT_FW;
+	val = AN8855_PAE_BPDU_FR |
+	      FIELD_PREP(AN8855_PAE_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
+	      FIELD_PREP(AN8855_PAE_PORT_FW, AN8855_BPDU_CPU_ONLY);
+	ret = regmap_update_bits(priv->regmap, AN8855_PAC, mask, val);
+	if (ret)
+		return ret;
+
+	/* Trap frames with :01 and :02 MAC DAs to the CPU port(s) and egress
+	 * them VLAN-untagged.
+	 */
+	mask = AN8855_R01_BPDU_FR | AN8855_R01_EG_TAG | AN8855_R01_PORT_FW |
+	       AN8855_R02_BPDU_FR | AN8855_R02_EG_TAG | AN8855_R02_PORT_FW;
+	val = AN8855_R01_BPDU_FR |
+	      FIELD_PREP(AN8855_R01_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
+	      FIELD_PREP(AN8855_R01_PORT_FW, AN8855_BPDU_CPU_ONLY) |
+	      AN8855_R02_BPDU_FR |
+	      FIELD_PREP(AN8855_R02_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
+	      FIELD_PREP(AN8855_R02_PORT_FW, AN8855_BPDU_CPU_ONLY);
+	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1, mask, val);
+	if (ret)
+		return ret;
+
+	/* Trap frames with :03 and :0E MAC DAs to the CPU port(s) and egress
+	 * them VLAN-untagged.
+	 */
+	mask = AN8855_R03_BPDU_FR | AN8855_R03_EG_TAG | AN8855_R03_PORT_FW |
+	       AN8855_R0E_BPDU_FR | AN8855_R0E_EG_TAG | AN8855_R0E_PORT_FW;
+	val = AN8855_R03_BPDU_FR |
+	      FIELD_PREP(AN8855_R03_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
+	      FIELD_PREP(AN8855_R03_PORT_FW, AN8855_BPDU_CPU_ONLY) |
+	      AN8855_R0E_BPDU_FR |
+	      FIELD_PREP(AN8855_R0E_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
+	      FIELD_PREP(AN8855_R0E_PORT_FW, AN8855_BPDU_CPU_ONLY);
+	return regmap_update_bits(priv->regmap, AN8855_RGAC2, mask, val);
+}
+
+static int an8855_setup_pvid_vlan(struct an8855_priv *priv)
+{
+	u32 val;
+	int ret;
+
+	/* Validate the entry with independent learning, keep the original
+	 * ingress tag attribute.
+	 */
+	val = AN8855_VA0_IVL_MAC | AN8855_VA0_EG_CON |
+	      FIELD_PREP(AN8855_VA0_FID, AN8855_FID_BRIDGED) |
+	      AN8855_VA0_PORT | AN8855_VA0_VLAN_VALID;
+	ret = regmap_write(priv->regmap, AN8855_VAWD0, val);
+	if (ret)
+		return ret;
+
+	return an8855_vlan_cmd(priv, AN8855_VTCR_WR_VID,
+			       AN8855_PORT_VID_DEFAULT);
+}
+
+static int an8855_setup(struct dsa_switch *ds)
+{
+	struct an8855_priv *priv = ds->priv;
+	struct dsa_port *dp;
+	int ret;
+
+	/* Enable and reset MIB counters */
+	ret = an8855_mib_init(priv);
+	if (ret)
+		return ret;
+
+	dsa_switch_for_each_user_port(dp, ds) {
+		/* Disable MAC by default on all user ports */
+		an8855_port_disable(ds, dp->index);
+
+		/* Individual user ports get connected to CPU port only */
+		ret = regmap_write(priv->regmap, AN8855_PORTMATRIX_P(dp->index),
+				   FIELD_PREP(AN8855_PORTMATRIX, BIT(AN8855_CPU_PORT)));
+		if (ret)
+			return ret;
+
+		/* Disable Broadcast Forward on user ports */
+		ret = regmap_clear_bits(priv->regmap, AN8855_BCF, BIT(dp->index));
+		if (ret)
+			return ret;
+
+		/* Disable Unknown Unicast Forward on user ports */
+		ret = regmap_clear_bits(priv->regmap, AN8855_UNUF, BIT(dp->index));
+		if (ret)
+			return ret;
+
+		/* Disable Unknown Multicast Forward on user ports */
+		ret = regmap_clear_bits(priv->regmap, AN8855_UNMF, BIT(dp->index));
+		if (ret)
+			return ret;
+
+		ret = regmap_clear_bits(priv->regmap, AN8855_UNIPMF, BIT(dp->index));
+		if (ret)
+			return ret;
+
+		/* Set default PVID to on all user ports */
+		ret = an8855_port_set_pvid(priv, dp->index, AN8855_PORT_VID_DEFAULT);
+		if (ret)
+			return ret;
+	}
+
+	/* Enable Airoha header mode on the cpu port */
+	ret = regmap_write(priv->regmap, AN8855_PVC_P(AN8855_CPU_PORT),
+			   AN8855_PORT_SPEC_REPLACE_MODE | AN8855_PORT_SPEC_TAG);
+	if (ret)
+		return ret;
+
+	/* Unknown multicast frame forwarding to the cpu port */
+	ret = regmap_write(priv->regmap, AN8855_UNMF, BIT(AN8855_CPU_PORT));
+	if (ret)
+		return ret;
+
+	/* Set CPU port number */
+	ret = regmap_update_bits(priv->regmap, AN8855_MFC,
+				 AN8855_CPU_EN | AN8855_CPU_PORT_IDX,
+				 AN8855_CPU_EN |
+				 FIELD_PREP(AN8855_CPU_PORT_IDX, AN8855_CPU_PORT));
+	if (ret)
+		return ret;
+
+	/* CPU port gets connected to all user ports of
+	 * the switch.
+	 */
+	ret = regmap_write(priv->regmap, AN8855_PORTMATRIX_P(AN8855_CPU_PORT),
+			   FIELD_PREP(AN8855_PORTMATRIX, dsa_user_ports(ds)));
+	if (ret)
+		return ret;
+
+	/* CPU port is set to fallback mode to let untagged
+	 * frames pass through.
+	 */
+	ret = regmap_update_bits(priv->regmap, AN8855_PCR_P(AN8855_CPU_PORT),
+				 AN8855_PORT_VLAN,
+				 FIELD_PREP(AN8855_PORT_VLAN, AN8855_PORT_FALLBACK_MODE));
+	if (ret)
+		return ret;
+
+	/* Enable Broadcast Forward on CPU port */
+	ret = regmap_set_bits(priv->regmap, AN8855_BCF, BIT(AN8855_CPU_PORT));
+	if (ret)
+		return ret;
+
+	/* Enable Unknown Unicast Forward on CPU port */
+	ret = regmap_set_bits(priv->regmap, AN8855_UNUF, BIT(AN8855_CPU_PORT));
+	if (ret)
+		return ret;
+
+	/* Enable Unknown Multicast Forward on CPU port */
+	ret = regmap_set_bits(priv->regmap, AN8855_UNMF, BIT(AN8855_CPU_PORT));
+	if (ret)
+		return ret;
+
+	ret = regmap_set_bits(priv->regmap, AN8855_UNIPMF, BIT(AN8855_CPU_PORT));
+	if (ret)
+		return ret;
+
+	/* Setup Trap special frame to CPU rules */
+	ret = an8855_trap_special_frames(priv);
+	if (ret)
+		return ret;
+
+	dsa_switch_for_each_port(dp, ds) {
+		/* Disable Learning on all ports.
+		 * Learning on CPU is disabled for fdb isolation and handled by
+		 * assisted_learning_on_cpu_port.
+		 */
+		ret = regmap_set_bits(priv->regmap, AN8855_PSC_P(dp->index),
+				      AN8855_SA_DIS);
+		if (ret)
+			return ret;
+
+		/* Enable consistent egress tag (for VLAN unware VLAN-passthrough) */
+		ret = regmap_update_bits(priv->regmap, AN8855_PVC_P(dp->index),
+					 AN8855_PVC_EG_TAG,
+					 FIELD_PREP(AN8855_PVC_EG_TAG, AN8855_VLAN_EG_CONSISTENT));
+		if (ret)
+			return ret;
+	}
+
+	/* Setup VLAN for Default PVID */
+	ret = an8855_setup_pvid_vlan(priv);
+	if (ret)
+		return ret;
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_CKGCR,
+				AN8855_CKG_LNKDN_GLB_STOP | AN8855_CKG_LNKDN_PORT_STOP);
+	if (ret)
+		return ret;
+
+	/* Flush the FDB table */
+	ret = an8855_fdb_cmd(priv, AN8855_FDB_FLUSH, NULL);
+	if (ret < 0)
+		return ret;
+
+	/* Set min a max ageing value supported */
+	ds->ageing_time_min = AN8855_L2_AGING_MS_CONSTANT;
+	ds->ageing_time_max = FIELD_MAX(AN8855_AGE_CNT) *
+			      FIELD_MAX(AN8855_AGE_UNIT) *
+			      AN8855_L2_AGING_MS_CONSTANT;
+
+	/* User reported problem with WiFi roaming and
+	 * ethernet port. Enabling assisted learning fix
+	 * the issue.
+	 */
+	ds->assisted_learning_on_cpu_port = true;
+
+	return 0;
+}
+
+static struct phylink_pcs *an8855_phylink_mac_select_pcs(struct phylink_config *config,
+							 phy_interface_t interface)
+{
+	struct dsa_port *dp = dsa_phylink_to_port(config);
+	struct an8855_priv *priv = dp->ds->priv;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_2500BASEX:
+		return &priv->pcs;
+	default:
+		return NULL;
+	}
+}
+
+static void an8855_phylink_mac_config(struct phylink_config *config,
+				      unsigned int mode,
+				      const struct phylink_link_state *state)
+{
+	struct dsa_port *dp = dsa_phylink_to_port(config);
+	struct dsa_switch *ds = dp->ds;
+	struct an8855_priv *priv;
+	int port = dp->index;
+
+	priv = ds->priv;
+
+	/* Nothing to configure for internal ports */
+	if (port != 5)
+		return;
+
+	regmap_update_bits(priv->regmap, AN8855_PMCR_P(port),
+			   AN8855_PMCR_IFG_XMIT | AN8855_PMCR_MAC_MODE |
+			   AN8855_PMCR_BACKOFF_EN | AN8855_PMCR_BACKPR_EN,
+			   FIELD_PREP(AN8855_PMCR_IFG_XMIT, 0x1) |
+			   AN8855_PMCR_MAC_MODE | AN8855_PMCR_BACKOFF_EN |
+			   AN8855_PMCR_BACKPR_EN);
+}
+
+static void an8855_phylink_get_caps(struct dsa_switch *ds, int port,
+				    struct phylink_config *config)
+{
+	struct an8855_priv *priv = ds->priv;
+	u32 reg;
+	int ret;
+
+	switch (port) {
+	case 0:
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		__set_bit(PHY_INTERFACE_MODE_GMII,
+			  config->supported_interfaces);
+		__set_bit(PHY_INTERFACE_MODE_INTERNAL,
+			  config->supported_interfaces);
+		break;
+	case 5:
+		phy_interface_set_rgmii(config->supported_interfaces);
+		__set_bit(PHY_INTERFACE_MODE_SGMII,
+			  config->supported_interfaces);
+		__set_bit(PHY_INTERFACE_MODE_2500BASEX,
+			  config->supported_interfaces);
+		break;
+	}
+
+	config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+				   MAC_10 | MAC_100 | MAC_1000FD | MAC_2500FD;
+
+	ret = regmap_read(priv->regmap, AN8855_CKGCR, &reg);
+	if (ret)
+		dev_err(ds->dev, "failed to read EEE LPI timer\n");
+
+	config->lpi_capabilities = MAC_100FD | MAC_1000FD;
+	/* Global LPI TXIDLE Threshold, default 60ms (unit 2us) */
+	config->lpi_timer_default = FIELD_GET(AN8855_LPI_TXIDLE_THD_MASK, reg) *
+				    AN8855_TX_LPI_UNIT;
+}
+
+static void an8855_phylink_mac_link_down(struct phylink_config *config,
+					 unsigned int mode,
+					 phy_interface_t interface)
+{
+	struct dsa_port *dp = dsa_phylink_to_port(config);
+	struct an8855_priv *priv = dp->ds->priv;
+
+	/* With autoneg just disable TX/RX else also force link down */
+	if (phylink_autoneg_inband(mode)) {
+		regmap_clear_bits(priv->regmap, AN8855_PMCR_P(dp->index),
+				  AN8855_PMCR_TX_EN | AN8855_PMCR_RX_EN);
+	} else {
+		regmap_update_bits(priv->regmap, AN8855_PMCR_P(dp->index),
+				   AN8855_PMCR_TX_EN | AN8855_PMCR_RX_EN |
+				   AN8855_PMCR_FORCE_MODE | AN8855_PMCR_FORCE_LNK,
+				   AN8855_PMCR_FORCE_MODE);
+	}
+}
+
+static void an8855_phylink_mac_link_up(struct phylink_config *config,
+				       struct phy_device *phydev, unsigned int mode,
+				       phy_interface_t interface, int speed,
+				       int duplex, bool tx_pause, bool rx_pause)
+{
+	struct dsa_port *dp = dsa_phylink_to_port(config);
+	struct an8855_priv *priv = dp->ds->priv;
+	int port = dp->index;
+	u32 reg;
+
+	reg = regmap_read(priv->regmap, AN8855_PMCR_P(port), &reg);
+	if (phylink_autoneg_inband(mode)) {
+		reg &= ~AN8855_PMCR_FORCE_MODE;
+	} else {
+		reg |= AN8855_PMCR_FORCE_MODE | AN8855_PMCR_FORCE_LNK;
+
+		reg &= ~AN8855_PMCR_FORCE_SPEED;
+		switch (speed) {
+		case SPEED_10:
+			reg |= AN8855_PMCR_FORCE_SPEED_10;
+			break;
+		case SPEED_100:
+			reg |= AN8855_PMCR_FORCE_SPEED_100;
+			break;
+		case SPEED_1000:
+			reg |= AN8855_PMCR_FORCE_SPEED_1000;
+			break;
+		case SPEED_2500:
+			reg |= AN8855_PMCR_FORCE_SPEED_2500;
+			break;
+		case SPEED_5000:
+			dev_err(priv->ds->dev, "Missing support for 5G speed. Aborting...\n");
+			return;
+		}
+
+		reg &= ~AN8855_PMCR_FORCE_FDX;
+		if (duplex == DUPLEX_FULL)
+			reg |= AN8855_PMCR_FORCE_FDX;
+
+		reg &= ~AN8855_PMCR_RX_FC_EN;
+		if (rx_pause || dsa_port_is_cpu(dp))
+			reg |= AN8855_PMCR_RX_FC_EN;
+
+		reg &= ~AN8855_PMCR_TX_FC_EN;
+		if (rx_pause || dsa_port_is_cpu(dp))
+			reg |= AN8855_PMCR_TX_FC_EN;
+	}
+
+	reg |= AN8855_PMCR_TX_EN | AN8855_PMCR_RX_EN;
+
+	regmap_write(priv->regmap, AN8855_PMCR_P(port), reg);
+}
+
+static void an8855_phylink_mac_disable_tx_lpi(struct phylink_config *config)
+{
+	struct dsa_port *dp = dsa_phylink_to_port(config);
+	struct an8855_priv *priv = dp->ds->priv;
+	int port = dp->index;
+	int ret;
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_PMCR_P(port),
+				AN8855_PMCR_FORCE_EEE1G |
+				AN8855_PMCR_FORCE_EEE100);
+	if (ret)
+		dev_err(dp->ds->dev, "failed to disable EEE for port %d\n",
+			port);
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_PMEEECR_P(port),
+				AN8855_LPI_MODE_EN);
+	if (ret)
+		dev_err(dp->ds->dev, "failed to disable LPI for port %d\n",
+			port);
+}
+
+static int an8855_phylink_mac_enable_tx_lpi(struct phylink_config *config,
+					    u32 timer, bool tx_clock_stop)
+{
+	struct dsa_port *dp, *other_dp;
+	struct an8855_priv *priv;
+	struct dsa_switch *ds;
+	int port;
+	u32 val;
+	int ret;
+
+	dp = dsa_phylink_to_port(config);
+	port = dp->index;
+	ds = dp->ds;
+	priv = ds->priv;
+
+	/* TX LPI timer is global, find the highest timer
+	 * across all port.
+	 * If requested timer is 0, set to enter LPI immediately
+	 * for the single port.
+	 */
+	if (timer) {
+		dsa_switch_for_each_user_port(other_dp, ds) {
+			struct phy_device *phydev;
+			struct net_device *dev;
+
+			if (other_dp == dp)
+				continue;
+
+			dev = other_dp->user;
+			phydev = dev->phydev;
+
+			if (timer > phydev->eee_cfg.tx_lpi_timer)
+				timer = phydev->eee_cfg.tx_lpi_timer;
+		}
+
+		timer /= AN8855_TX_LPI_UNIT;
+		if (FIELD_FIT(AN8855_LPI_TXIDLE_THD_MASK, timer))
+			val = FIELD_PREP(AN8855_LPI_TXIDLE_THD_MASK, timer);
+		else
+			val = AN8855_LPI_TXIDLE_THD_MASK;
+
+		ret = regmap_update_bits(priv->regmap, AN8855_CKGCR,
+					 AN8855_LPI_TXIDLE_THD_MASK, val);
+		if (ret) {
+			dev_err(dp->ds->dev, "failed to set global LPI timer\n");
+			return ret;
+		}
+	} else {
+		ret = regmap_set_bits(priv->regmap, AN8855_PMEEECR_P(port),
+				      AN8855_LPI_MODE_EN);
+		if (ret) {
+			dev_err(dp->ds->dev, "failed to enable LPI for port %d\n",
+				port);
+			return ret;
+		}
+	}
+
+	ret = regmap_set_bits(priv->regmap, AN8855_PMCR_P(port),
+			      AN8855_PMCR_FORCE_EEE1G |
+			      AN8855_PMCR_FORCE_EEE100);
+	if (ret)
+		dev_err(dp->ds->dev, "failed to enable EEE for port %d\n",
+			port);
+
+	return ret;
+}
+
+static unsigned int an8855_pcs_inband_caps(struct phylink_pcs *pcs,
+					   phy_interface_t interface)
+{
+	/* SGMII can be configured to use inband with AN result */
+	if (interface == PHY_INTERFACE_MODE_SGMII)
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+
+	/* inband is not supported in 2500-baseX and must be disabled */
+	return LINK_INBAND_DISABLE;
+}
+
+static void an8855_pcs_get_state(struct phylink_pcs *pcs, unsigned int neg_mode,
+				 struct phylink_link_state *state)
+{
+	struct an8855_priv *priv = container_of(pcs, struct an8855_priv, pcs);
+	u32 val;
+	int ret;
+
+	ret = regmap_read(priv->regmap, AN8855_PMSR_P(AN8855_CPU_PORT), &val);
+	if (ret < 0) {
+		state->link = false;
+		return;
+	}
+
+	state->link = !!(val & AN8855_PMSR_LNK);
+	state->an_complete = state->link;
+	state->duplex = (val & AN8855_PMSR_DPX) ? DUPLEX_FULL :
+						  DUPLEX_HALF;
+
+	switch (val & AN8855_PMSR_SPEED) {
+	case AN8855_PMSR_SPEED_10:
+		state->speed = SPEED_10;
+		break;
+	case AN8855_PMSR_SPEED_100:
+		state->speed = SPEED_100;
+		break;
+	case AN8855_PMSR_SPEED_1000:
+		state->speed = SPEED_1000;
+		break;
+	case AN8855_PMSR_SPEED_2500:
+		state->speed = SPEED_2500;
+		break;
+	case AN8855_PMSR_SPEED_5000:
+		dev_err(priv->ds->dev, "Switch doesn't support 5G speed. Setting Unknown.\n");
+		fallthrough;
+	default:
+		state->speed = SPEED_UNKNOWN;
+		break;
+	}
+
+	if (val & AN8855_PMSR_RX_FC)
+		state->pause |= MLO_PAUSE_RX;
+	if (val & AN8855_PMSR_TX_FC)
+		state->pause |= MLO_PAUSE_TX;
+}
+
+static int an8855_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
+			     phy_interface_t interface,
+			     const unsigned long *advertising,
+			     bool permit_pause_to_mac)
+{
+	struct an8855_priv *priv = container_of(pcs, struct an8855_priv, pcs);
+	u32 val;
+	int ret;
+
+	/* TX FIR - improve TX EYE */
+	ret = regmap_update_bits(priv->regmap, AN8855_INTF_CTRL_10,
+				 AN8855_RG_DA_QP_TX_FIR_C2_SEL |
+				 AN8855_RG_DA_QP_TX_FIR_C2_FORCE |
+				 AN8855_RG_DA_QP_TX_FIR_C1_SEL |
+				 AN8855_RG_DA_QP_TX_FIR_C1_FORCE,
+				 AN8855_RG_DA_QP_TX_FIR_C2_SEL |
+				 FIELD_PREP(AN8855_RG_DA_QP_TX_FIR_C2_FORCE, 0x4) |
+				 AN8855_RG_DA_QP_TX_FIR_C1_SEL |
+				 FIELD_PREP(AN8855_RG_DA_QP_TX_FIR_C1_FORCE, 0x0));
+	if (ret)
+		return ret;
+
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x0;
+	else
+		val = 0xd;
+	ret = regmap_update_bits(priv->regmap, AN8855_INTF_CTRL_11,
+				 AN8855_RG_DA_QP_TX_FIR_C0B_SEL |
+				 AN8855_RG_DA_QP_TX_FIR_C0B_FORCE,
+				 AN8855_RG_DA_QP_TX_FIR_C0B_SEL |
+				 FIELD_PREP(AN8855_RG_DA_QP_TX_FIR_C0B_FORCE, val));
+	if (ret)
+		return ret;
+
+	/* RX CDR - improve RX Jitter Tolerance */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x5;
+	else
+		val = 0x6;
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_LPF_BOT_LIM,
+				 AN8855_RG_QP_CDR_LPF_KP_GAIN |
+				 AN8855_RG_QP_CDR_LPF_KI_GAIN,
+				 FIELD_PREP(AN8855_RG_QP_CDR_LPF_KP_GAIN, val) |
+				 FIELD_PREP(AN8855_RG_QP_CDR_LPF_KI_GAIN, val));
+	if (ret)
+		return ret;
+
+	/* PLL */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x1;
+	else
+		val = 0x0;
+	ret = regmap_update_bits(priv->regmap, AN8855_QP_DIG_MODE_CTRL_1,
+				 AN8855_RG_TPHY_SPEED,
+				 FIELD_PREP(AN8855_RG_TPHY_SPEED, val));
+	if (ret)
+		return ret;
+
+	/* PLL - LPF */
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				 AN8855_RG_DA_QP_PLL_RICO_SEL_INTF |
+				 AN8855_RG_DA_QP_PLL_FBKSEL_INTF |
+				 AN8855_RG_DA_QP_PLL_BR_INTF |
+				 AN8855_RG_DA_QP_PLL_BPD_INTF |
+				 AN8855_RG_DA_QP_PLL_BPA_INTF |
+				 AN8855_RG_DA_QP_PLL_BC_INTF,
+				 AN8855_RG_DA_QP_PLL_RICO_SEL_INTF |
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_FBKSEL_INTF, 0x0) |
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_BR_INTF, 0x3) |
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_BPD_INTF, 0x0) |
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_BPA_INTF, 0x5) |
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_BC_INTF, 0x1));
+	if (ret)
+		return ret;
+
+	/* PLL - ICO */
+	ret = regmap_set_bits(priv->regmap, AN8855_PLL_CTRL_4,
+			      AN8855_RG_DA_QP_PLL_ICOLP_EN_INTF);
+	if (ret)
+		return ret;
+	ret = regmap_clear_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				AN8855_RG_DA_QP_PLL_ICOIQ_EN_INTF);
+	if (ret)
+		return ret;
+
+	/* PLL - CHP */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x6;
+	else
+		val = 0x4;
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				 AN8855_RG_DA_QP_PLL_IR_INTF,
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_IR_INTF, val));
+	if (ret)
+		return ret;
+
+	/* PLL - PFD */
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				 AN8855_RG_DA_QP_PLL_PFD_OFFSET_EN_INTRF |
+				 AN8855_RG_DA_QP_PLL_PFD_OFFSET_INTF |
+				 AN8855_RG_DA_QP_PLL_KBAND_PREDIV_INTF,
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_PFD_OFFSET_INTF, 0x1) |
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_KBAND_PREDIV_INTF, 0x1));
+	if (ret)
+		return ret;
+
+	/* PLL - POSTDIV */
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				 AN8855_RG_DA_QP_PLL_POSTDIV_EN_INTF |
+				 AN8855_RG_DA_QP_PLL_PHY_CK_EN_INTF |
+				 AN8855_RG_DA_QP_PLL_PCK_SEL_INTF,
+				 AN8855_RG_DA_QP_PLL_PCK_SEL_INTF);
+	if (ret)
+		return ret;
+
+	/* PLL - SDM */
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				 AN8855_RG_DA_QP_PLL_SDM_HREN_INTF,
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_SDM_HREN_INTF, 0x0));
+	if (ret)
+		return ret;
+	ret = regmap_clear_bits(priv->regmap, AN8855_PLL_CTRL_2,
+				AN8855_RG_DA_QP_PLL_SDM_IFM_INTF);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_SS_LCPLL_PWCTL_SETTING_2,
+				 AN8855_RG_NCPO_ANA_MSB,
+				 FIELD_PREP(AN8855_RG_NCPO_ANA_MSB, 0x1));
+	if (ret)
+		return ret;
+
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x7a000000;
+	else
+		val = 0x48000000;
+	ret = regmap_write(priv->regmap, AN8855_SS_LCPLL_TDC_FLT_2,
+			   FIELD_PREP(AN8855_RG_LCPLL_NCPO_VALUE, val));
+	if (ret)
+		return ret;
+	ret = regmap_write(priv->regmap, AN8855_SS_LCPLL_TDC_PCW_1,
+			   FIELD_PREP(AN8855_RG_LCPLL_PON_HRDDS_PCW_NCPO_GPON, val));
+	if (ret)
+		return ret;
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_SS_LCPLL_TDC_FLT_5,
+				AN8855_RG_LCPLL_NCPO_CHG);
+	if (ret)
+		return ret;
+	ret = regmap_clear_bits(priv->regmap, AN8855_PLL_CK_CTRL_0,
+				AN8855_RG_DA_QP_PLL_SDM_DI_EN_INTF);
+	if (ret)
+		return ret;
+
+	/* PLL - SS */
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_3,
+				 AN8855_RG_DA_QP_PLL_SSC_DELTA_INTF,
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_SSC_DELTA_INTF, 0x0));
+	if (ret)
+		return ret;
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_4,
+				 AN8855_RG_DA_QP_PLL_SSC_DIR_DLY_INTF,
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_SSC_DIR_DLY_INTF, 0x0));
+	if (ret)
+		return ret;
+	ret = regmap_update_bits(priv->regmap, AN8855_PLL_CTRL_3,
+				 AN8855_RG_DA_QP_PLL_SSC_PERIOD_INTF,
+				 FIELD_PREP(AN8855_RG_DA_QP_PLL_SSC_PERIOD_INTF, 0x0));
+	if (ret)
+		return ret;
+
+	/* PLL - TDC */
+	ret = regmap_clear_bits(priv->regmap, AN8855_PLL_CK_CTRL_0,
+				AN8855_RG_DA_QP_PLL_TDC_TXCK_SEL_INTF);
+	if (ret)
+		return ret;
+
+	ret = regmap_set_bits(priv->regmap, AN8855_RG_QP_PLL_SDM_ORD,
+			      AN8855_RG_QP_PLL_SSC_TRI_EN);
+	if (ret)
+		return ret;
+	ret = regmap_set_bits(priv->regmap, AN8855_RG_QP_PLL_SDM_ORD,
+			      AN8855_RG_QP_PLL_SSC_PHASE_INI);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_RX_DAC_EN,
+				 AN8855_RG_QP_SIGDET_HF,
+				 FIELD_PREP(AN8855_RG_QP_SIGDET_HF, 0x2));
+	if (ret)
+		return ret;
+
+	/* TCL Disable (only for Co-SIM) */
+	ret = regmap_clear_bits(priv->regmap, AN8855_PON_RXFEDIG_CTRL_0,
+				AN8855_RG_QP_EQ_RX500M_CK_SEL);
+	if (ret)
+		return ret;
+
+	/* TX Init */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x4;
+	else
+		val = 0x0;
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_TX_MODE,
+				 AN8855_RG_QP_TX_RESERVE |
+				 AN8855_RG_QP_TX_MODE_16B_EN,
+				 FIELD_PREP(AN8855_RG_QP_TX_RESERVE, val));
+	if (ret)
+		return ret;
+
+	/* RX Control/Init */
+	ret = regmap_set_bits(priv->regmap, AN8855_RG_QP_RXAFE_RESERVE,
+			      AN8855_RG_QP_CDR_PD_10B_EN);
+	if (ret)
+		return ret;
+
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x1;
+	else
+		val = 0x2;
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_LPF_MJV_LIM,
+				 AN8855_RG_QP_CDR_LPF_RATIO,
+				 FIELD_PREP(AN8855_RG_QP_CDR_LPF_RATIO, val));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_LPF_SETVALUE,
+				 AN8855_RG_QP_CDR_PR_BUF_IN_SR |
+				 AN8855_RG_QP_CDR_PR_BETA_SEL,
+				 FIELD_PREP(AN8855_RG_QP_CDR_PR_BUF_IN_SR, 0x6) |
+				 FIELD_PREP(AN8855_RG_QP_CDR_PR_BETA_SEL, 0x1));
+	if (ret)
+		return ret;
+
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0xf;
+	else
+		val = 0xc;
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_PR_CKREF_DIV1,
+				 AN8855_RG_QP_CDR_PR_DAC_BAND,
+				 FIELD_PREP(AN8855_RG_QP_CDR_PR_DAC_BAND, val));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_PR_KBAND_DIV_PCIE,
+				 AN8855_RG_QP_CDR_PR_KBAND_PCIE_MODE |
+				 AN8855_RG_QP_CDR_PR_KBAND_DIV_PCIE_MASK,
+				 FIELD_PREP(AN8855_RG_QP_CDR_PR_KBAND_DIV_PCIE_MASK, 0x19));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_FORCE_IBANDLPF_R_OFF,
+				 AN8855_RG_QP_CDR_PHYCK_SEL |
+				 AN8855_RG_QP_CDR_PHYCK_RSTB |
+				 AN8855_RG_QP_CDR_PHYCK_DIV,
+				 FIELD_PREP(AN8855_RG_QP_CDR_PHYCK_SEL, 0x2) |
+				 FIELD_PREP(AN8855_RG_QP_CDR_PHYCK_DIV, 0x21));
+	if (ret)
+		return ret;
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_RG_QP_CDR_PR_KBAND_DIV_PCIE,
+				AN8855_RG_QP_CDR_PR_XFICK_EN);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RG_QP_CDR_PR_CKREF_DIV1,
+				 AN8855_RG_QP_CDR_PR_KBAND_DIV,
+				 FIELD_PREP(AN8855_RG_QP_CDR_PR_KBAND_DIV, 0x4));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_26,
+				 AN8855_RG_QP_EQ_RETRAIN_ONLY_EN |
+				 AN8855_RG_LINK_NE_EN |
+				 AN8855_RG_LINK_ERRO_EN,
+				 AN8855_RG_QP_EQ_RETRAIN_ONLY_EN |
+				 AN8855_RG_LINK_ERRO_EN);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_DLY_0,
+				 AN8855_RG_QP_RX_SAOSC_EN_H_DLY |
+				 AN8855_RG_QP_RX_PI_CAL_EN_H_DLY,
+				 FIELD_PREP(AN8855_RG_QP_RX_SAOSC_EN_H_DLY, 0x3f) |
+				 FIELD_PREP(AN8855_RG_QP_RX_PI_CAL_EN_H_DLY, 0x6f));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_42,
+				 AN8855_RG_QP_EQ_EN_DLY,
+				 FIELD_PREP(AN8855_RG_QP_EQ_EN_DLY, 0x150));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_2,
+				 AN8855_RG_QP_RX_EQ_EN_H_DLY,
+				 FIELD_PREP(AN8855_RG_QP_RX_EQ_EN_H_DLY, 0x150));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_PON_RXFEDIG_CTRL_9,
+				 AN8855_RG_QP_EQ_LEQOSC_DLYCNT,
+				 FIELD_PREP(AN8855_RG_QP_EQ_LEQOSC_DLYCNT, 0x1));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_8,
+				 AN8855_RG_DA_QP_SAOSC_DONE_TIME |
+				 AN8855_RG_DA_QP_LEQOS_EN_TIME,
+				 FIELD_PREP(AN8855_RG_DA_QP_SAOSC_DONE_TIME, 0x200) |
+				 FIELD_PREP(AN8855_RG_DA_QP_LEQOS_EN_TIME, 0xfff));
+	if (ret)
+		return ret;
+
+	/* Frequency meter */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
+		val = 0x10;
+	else
+		val = 0x28;
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_5,
+				 AN8855_RG_FREDET_CHK_CYCLE,
+				 FIELD_PREP(AN8855_RG_FREDET_CHK_CYCLE, val));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_6,
+				 AN8855_RG_FREDET_GOLDEN_CYCLE,
+				 FIELD_PREP(AN8855_RG_FREDET_GOLDEN_CYCLE, 0x64));
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap, AN8855_RX_CTRL_7,
+				 AN8855_RG_FREDET_TOLERATE_CYCLE,
+				 FIELD_PREP(AN8855_RG_FREDET_TOLERATE_CYCLE, 0x2710));
+	if (ret)
+		return ret;
+
+	ret = regmap_set_bits(priv->regmap, AN8855_PLL_CTRL_0,
+			      AN8855_RG_PHYA_AUTO_INIT);
+	if (ret)
+		return ret;
+
+	/* PCS Init */
+	if (interface == PHY_INTERFACE_MODE_SGMII &&
+	    neg_mode == PHYLINK_PCS_NEG_INBAND_DISABLED) {
+		ret = regmap_clear_bits(priv->regmap, AN8855_QP_DIG_MODE_CTRL_0,
+					AN8855_RG_SGMII_MODE | AN8855_RG_SGMII_AN_EN);
+		if (ret)
+			return ret;
+	}
+
+	ret = regmap_clear_bits(priv->regmap, AN8855_RG_HSGMII_PCS_CTROL_1,
+				AN8855_RG_TBI_10B_MODE);
+	if (ret)
+		return ret;
+
+	if (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) {
+		/* Set AN Ability - Interrupt */
+		ret = regmap_set_bits(priv->regmap, AN8855_SGMII_REG_AN_FORCE_CL37,
+				      AN8855_RG_FORCE_AN_DONE);
+		if (ret)
+			return ret;
+
+		ret = regmap_update_bits(priv->regmap, AN8855_SGMII_REG_AN_13,
+					 AN8855_SGMII_REMOTE_FAULT_DIS |
+					 AN8855_SGMII_IF_MODE,
+					 AN8855_SGMII_REMOTE_FAULT_DIS |
+					 FIELD_PREP(AN8855_SGMII_IF_MODE, 0xb));
+		if (ret)
+			return ret;
+	}
+
+	/* Rate Adaption - GMII path config. */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX) {
+		ret = regmap_clear_bits(priv->regmap, AN8855_RATE_ADP_P0_CTRL_0,
+					AN8855_RG_P0_DIS_MII_MODE);
+		if (ret)
+			return ret;
+	} else {
+		if (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) {
+			ret = regmap_set_bits(priv->regmap, AN8855_MII_RA_AN_ENABLE,
+					      AN8855_RG_P0_RA_AN_EN);
+			if (ret)
+				return ret;
+		} else {
+			ret = regmap_update_bits(priv->regmap, AN8855_RG_AN_SGMII_MODE_FORCE,
+						 AN8855_RG_FORCE_CUR_SGMII_MODE |
+						 AN8855_RG_FORCE_CUR_SGMII_SEL,
+						 AN8855_RG_FORCE_CUR_SGMII_SEL);
+			if (ret)
+				return ret;
+
+			ret = regmap_clear_bits(priv->regmap, AN8855_RATE_ADP_P0_CTRL_0,
+						AN8855_RG_P0_MII_RA_RX_EN |
+						AN8855_RG_P0_MII_RA_TX_EN |
+						AN8855_RG_P0_MII_RA_RX_MODE |
+						AN8855_RG_P0_MII_RA_TX_MODE);
+			if (ret)
+				return ret;
+		}
+
+		ret = regmap_set_bits(priv->regmap, AN8855_RATE_ADP_P0_CTRL_0,
+				      AN8855_RG_P0_MII_MODE);
+		if (ret)
+			return ret;
+	}
+
+	ret = regmap_set_bits(priv->regmap, AN8855_RG_RATE_ADAPT_CTRL_0,
+			      AN8855_RG_RATE_ADAPT_RX_BYPASS |
+			      AN8855_RG_RATE_ADAPT_TX_BYPASS |
+			      AN8855_RG_RATE_ADAPT_RX_EN |
+			      AN8855_RG_RATE_ADAPT_TX_EN);
+	if (ret)
+		return ret;
+
+	/* Disable AN if not in autoneg */
+	ret = regmap_update_bits(priv->regmap, AN8855_SGMII_REG_AN0, BMCR_ANENABLE,
+				 neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED ? BMCR_ANENABLE :
+									      0);
+	if (ret)
+		return ret;
+
+	if (interface == PHY_INTERFACE_MODE_SGMII) {
+		/* Follow SDK init flow with restarting AN after AN enable */
+		if (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) {
+			ret = regmap_set_bits(priv->regmap, AN8855_SGMII_REG_AN0,
+					      BMCR_ANRESTART);
+			if (ret)
+				return ret;
+		} else {
+			ret = regmap_set_bits(priv->regmap, AN8855_PHY_RX_FORCE_CTRL_0,
+					      AN8855_RG_FORCE_TXC_SEL);
+			if (ret)
+				return ret;
+		}
+	}
+
+	/* Force Speed with fixed-link or 2500base-x as doesn't support aneg */
+	if (interface == PHY_INTERFACE_MODE_2500BASEX ||
+	    neg_mode != PHYLINK_PCS_NEG_INBAND_ENABLED) {
+		if (interface == PHY_INTERFACE_MODE_2500BASEX)
+			val = AN8855_RG_LINK_MODE_P0_SPEED_2500;
+		else
+			val = AN8855_RG_LINK_MODE_P0_SPEED_1000;
+		ret = regmap_update_bits(priv->regmap, AN8855_SGMII_STS_CTRL_0,
+					 AN8855_RG_LINK_MODE_P0 |
+					 AN8855_RG_FORCE_SPD_MODE_P0,
+					 val | AN8855_RG_FORCE_SPD_MODE_P0);
+		if (ret)
+			return ret;
+	}
+
+	/* bypass flow control to MAC */
+	ret = regmap_write(priv->regmap, AN8855_MSG_RX_LIK_STS_0,
+			   AN8855_RG_DPX_STS_P3 | AN8855_RG_DPX_STS_P2 |
+			   AN8855_RG_DPX_STS_P1 | AN8855_RG_TXFC_STS_P0 |
+			   AN8855_RG_RXFC_STS_P0 | AN8855_RG_DPX_STS_P0);
+	if (ret)
+		return ret;
+	ret = regmap_write(priv->regmap, AN8855_MSG_RX_LIK_STS_2,
+			   AN8855_RG_RXFC_AN_BYPASS_P3 |
+			   AN8855_RG_RXFC_AN_BYPASS_P2 |
+			   AN8855_RG_RXFC_AN_BYPASS_P1 |
+			   AN8855_RG_TXFC_AN_BYPASS_P3 |
+			   AN8855_RG_TXFC_AN_BYPASS_P2 |
+			   AN8855_RG_TXFC_AN_BYPASS_P1 |
+			   AN8855_RG_DPX_AN_BYPASS_P3 |
+			   AN8855_RG_DPX_AN_BYPASS_P2 |
+			   AN8855_RG_DPX_AN_BYPASS_P1 |
+			   AN8855_RG_DPX_AN_BYPASS_P0);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void an8855_pcs_an_restart(struct phylink_pcs *pcs)
+{
+}
+
+static const struct phylink_pcs_ops an8855_pcs_ops = {
+	.pcs_inband_caps = an8855_pcs_inband_caps,
+	.pcs_get_state = an8855_pcs_get_state,
+	.pcs_config = an8855_pcs_config,
+	.pcs_an_restart = an8855_pcs_an_restart,
+};
+
+static const struct phylink_mac_ops an8855_phylink_mac_ops = {
+	.mac_select_pcs	= an8855_phylink_mac_select_pcs,
+	.mac_config	= an8855_phylink_mac_config,
+	.mac_link_down	= an8855_phylink_mac_link_down,
+	.mac_link_up	= an8855_phylink_mac_link_up,
+	.mac_disable_tx_lpi = an8855_phylink_mac_disable_tx_lpi,
+	.mac_enable_tx_lpi = an8855_phylink_mac_enable_tx_lpi,
+};
+
+static const struct dsa_switch_ops an8855_switch_ops = {
+	.get_tag_protocol = an8855_get_tag_protocol,
+	.setup = an8855_setup,
+	.phylink_get_caps = an8855_phylink_get_caps,
+	.get_strings = an8855_get_strings,
+	.get_ethtool_stats = an8855_get_ethtool_stats,
+	.get_sset_count = an8855_get_sset_count,
+	.get_eth_mac_stats = an8855_get_eth_mac_stats,
+	.get_eth_ctrl_stats = an8855_get_eth_ctrl_stats,
+	.get_rmon_stats = an8855_get_rmon_stats,
+	.port_enable = an8855_port_enable,
+	.port_disable = an8855_port_disable,
+	.set_ageing_time = an8855_set_ageing_time,
+	.port_bridge_join = an8855_port_bridge_join,
+	.port_bridge_leave = an8855_port_bridge_leave,
+	.port_fast_age = an8855_port_fast_age,
+	.port_stp_state_set = an8855_port_stp_state_set,
+	.port_pre_bridge_flags = an8855_port_pre_bridge_flags,
+	.port_bridge_flags = an8855_port_bridge_flags,
+	.port_vlan_filtering = an8855_port_vlan_filtering,
+	.port_vlan_add = an8855_port_vlan_add,
+	.port_vlan_del = an8855_port_vlan_del,
+	.port_fdb_add = an8855_port_fdb_add,
+	.port_fdb_del = an8855_port_fdb_del,
+	.port_fdb_dump = an8855_port_fdb_dump,
+	.port_mdb_add = an8855_port_mdb_add,
+	.port_mdb_del = an8855_port_mdb_del,
+	.port_change_mtu = an8855_port_change_mtu,
+	.port_max_mtu = an8855_port_max_mtu,
+	.port_mirror_add = an8855_port_mirror_add,
+	.port_mirror_del = an8855_port_mirror_del,
+	.support_eee = dsa_supports_eee,
+	.set_mac_eee = an8855_set_mac_eee,
+};
+
+static int an8855_switch_probe(struct platform_device *pdev)
+{
+	struct an8855_priv *priv;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	/* Get regmap from MFD */
+	priv->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!priv->regmap)
+		return -ENOENT;
+
+	priv->ds = devm_kzalloc(&pdev->dev, sizeof(*priv->ds), GFP_KERNEL);
+	if (!priv->ds)
+		return -ENOMEM;
+
+	priv->ds->dev = &pdev->dev;
+	priv->ds->num_ports = AN8855_NUM_PORTS;
+	priv->ds->priv = priv;
+	priv->ds->ops = &an8855_switch_ops;
+	devm_mutex_init(&pdev->dev, &priv->reg_mutex);
+	priv->ds->phylink_mac_ops = &an8855_phylink_mac_ops;
+
+	priv->pcs.ops = &an8855_pcs_ops;
+	priv->pcs.poll = true;
+
+	dev_set_drvdata(&pdev->dev, priv);
+
+	return dsa_register_switch(priv->ds);
+}
+
+static void an8855_switch_remove(struct platform_device *pdev)
+{
+	struct an8855_priv *priv = dev_get_drvdata(&pdev->dev);
+
+	if (!priv)
+		return;
+
+	dsa_unregister_switch(priv->ds);
+
+	dev_set_drvdata(&pdev->dev, NULL);
+}
+
+static void an8855_switch_shutdown(struct platform_device *pdev)
+{
+	struct an8855_priv *priv = dev_get_drvdata(&pdev->dev);
+
+	if (!priv)
+		return;
+
+	dsa_switch_shutdown(priv->ds);
+
+	dev_set_drvdata(&pdev->dev, NULL);
+}
+
+static const struct of_device_id an8855_switch_of_match[] = {
+	{ .compatible = "airoha,an8855-switch" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_switch_of_match);
+
+static struct platform_driver an8855_switch_driver = {
+	.probe = an8855_switch_probe,
+	.remove = an8855_switch_remove,
+	.shutdown = an8855_switch_shutdown,
+	.driver = {
+		.name = "an8855-switch",
+		.of_match_table = an8855_switch_of_match,
+	},
+};
+module_platform_driver(an8855_switch_driver);
+
+MODULE_AUTHOR("Min Yao <min.yao@airoha.com>");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for Airoha AN8855 Switch");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/dsa/an8855.h b/drivers/net/dsa/an8855.h
new file mode 100644
index 000000000000..15cafbb37ae5
--- /dev/null
+++ b/drivers/net/dsa/an8855.h
@@ -0,0 +1,773 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2023 Min Yao <min.yao@airoha.com>
+ * Copyright (C) 2024 Christian Marangi <ansuelsmth@gmail.com>
+ */
+
+#ifndef __AN8855_H
+#define __AN8855_H
+
+#include <linux/bitfield.h>
+
+#define AN8855_NUM_PORTS		6
+#define AN8855_CPU_PORT			5
+#define AN8855_NUM_FDB_RECORDS		2048
+#define AN8855_GPHY_SMI_ADDR_DEFAULT	1
+#define AN8855_PORT_VID_DEFAULT		0
+
+#define MTK_TAG_LEN			4
+#define AN8855_MAX_MTU			(15360 - ETH_HLEN - ETH_FCS_LEN - MTK_TAG_LEN)
+
+#define AN8855_L2_AGING_MS_CONSTANT	1024
+
+#define AN8855_TX_LPI_UNIT		2 /* us */
+
+/*	AN8855_SCU			0x10000000 */
+#define AN8855_RG_GPIO_LED_MODE		0x10000054
+#define AN8855_RG_GPIO_LED_SEL(i)	(0x10000000 + (0x0058 + ((i) * 4)))
+#define AN8855_RG_INTB_MODE		0x10000080
+#define AN8855_RG_RGMII_TXCK_C		0x100001d0
+
+#define AN8855_PKG_SEL			0x10000094
+#define   AN8855_PAG_SEL_AN8855H	0x2
+
+#define AN8855_RG_GPIO_L_INV		0x10000010
+#define AN8855_RG_GPIO_CTRL		0x1000a300
+#define AN8855_RG_GPIO_DATA		0x1000a304
+#define AN8855_RG_GPIO_OE		0x1000a314
+
+/* Register for system reset */
+#define AN8855_RST_CTRL			0x100050c0
+#define   AN8855_SYS_CTRL_SYS_RST	BIT(31)
+
+#define AN8855_INT_MASK			0x100050f0
+#define   AN8855_INT_SYS		BIT(15)
+
+#define AN8855_RG_CLK_CPU_ICG		0x10005034
+#define   AN8855_MCU_ENABLE		BIT(3)
+
+#define AN8855_RG_TIMER_CTL		0x1000a100
+#define   AN8855_WDOG_ENABLE		BIT(25)
+
+#define AN8855_RG_GDMP_RAM		0x10010000
+
+/* Registers to mac forward control for unknown frames */
+#define AN8855_MFC			0x10200010
+#define   AN8855_CPU_EN			BIT(15)
+#define   AN8855_CPU_PORT_IDX		GENMASK(12, 8)
+
+#define AN8855_PAC			0x10200024
+#define   AN8855_TAG_PAE_MANG_FR	BIT(30)
+#define   AN8855_TAG_PAE_BPDU_FR	BIT(28)
+#define   AN8855_TAG_PAE_EG_TAG		GENMASK(27, 25)
+#define   AN8855_TAG_PAE_LKY_VLAN	BIT(24)
+#define   AN8855_TAG_PAE_PRI_HIGH	BIT(23)
+#define   AN8855_TAG_PAE_MIR		GENMASK(20, 19)
+#define   AN8855_TAG_PAE_PORT_FW	GENMASK(18, 16)
+#define   AN8855_PAE_MANG_FR		BIT(14)
+#define   AN8855_PAE_BPDU_FR		BIT(12)
+#define   AN8855_PAE_EG_TAG		GENMASK(11, 9)
+#define   AN8855_PAE_LKY_VLAN		BIT(8)
+#define   AN8855_PAE_PRI_HIGH		BIT(7)
+#define   AN8855_PAE_MIR		GENMASK(4, 3)
+#define   AN8855_PAE_PORT_FW		GENMASK(2, 0)
+
+#define AN8855_RGAC1			0x10200028
+#define   AN8855_R02_MANG_FR		BIT(30)
+#define   AN8855_R02_BPDU_FR		BIT(28)
+#define   AN8855_R02_EG_TAG		GENMASK(27, 25)
+#define   AN8855_R02_LKY_VLAN		BIT(24)
+#define   AN8855_R02_PRI_HIGH		BIT(23)
+#define   AN8855_R02_MIR		GENMASK(20, 19)
+#define   AN8855_R02_PORT_FW		GENMASK(18, 16)
+#define   AN8855_R01_MANG_FR		BIT(14)
+#define   AN8855_R01_BPDU_FR		BIT(12)
+#define   AN8855_R01_EG_TAG		GENMASK(11, 9)
+#define   AN8855_R01_LKY_VLAN		BIT(8)
+#define   AN8855_R01_PRI_HIGH		BIT(7)
+#define   AN8855_R01_MIR		GENMASK(4, 3)
+#define   AN8855_R01_PORT_FW		GENMASK(2, 0)
+
+#define AN8855_RGAC2			0x1020002c
+#define   AN8855_R0E_MANG_FR		BIT(30)
+#define   AN8855_R0E_BPDU_FR		BIT(28)
+#define   AN8855_R0E_EG_TAG		GENMASK(27, 25)
+#define   AN8855_R0E_LKY_VLAN		BIT(24)
+#define   AN8855_R0E_PRI_HIGH		BIT(23)
+#define   AN8855_R0E_MIR		GENMASK(20, 19)
+#define   AN8855_R0E_PORT_FW		GENMASK(18, 16)
+#define   AN8855_R03_MANG_FR		BIT(14)
+#define   AN8855_R03_BPDU_FR		BIT(12)
+#define   AN8855_R03_EG_TAG		GENMASK(11, 9)
+#define   AN8855_R03_LKY_VLAN		BIT(8)
+#define   AN8855_R03_PRI_HIGH		BIT(7)
+#define   AN8855_R03_MIR		GENMASK(4, 3)
+#define   AN8855_R03_PORT_FW		GENMASK(2, 0)
+
+#define AN8855_AAC			0x102000a0
+#define   AN8855_MAC_AUTO_FLUSH		BIT(28)
+/* Control Address Table Age time.
+ * (AN8855_AGE_CNT + 1) * ( AN8855_AGE_UNIT + 1 ) * AN8855_L2_AGING_MS_CONSTANT
+ */
+#define   AN8855_AGE_CNT		GENMASK(20, 12)
+/* Value in seconds. Value is always incremented of 1 */
+#define   AN8855_AGE_UNIT		GENMASK(10, 0)
+
+/* Registers for ARL Unknown Unicast Forward control */
+#define AN8855_UNUF			0x102000b4
+
+/* Registers for ARL Unknown Multicast Forward control */
+#define AN8855_UNMF			0x102000b8
+
+/* Registers for ARL Broadcast forward control */
+#define AN8855_BCF			0x102000bc
+
+/* Registers for port address age disable */
+#define AN8855_AGDIS			0x102000c0
+
+/* Registers for mirror port control */
+#define AN8855_MIR			0x102000cc
+#define   AN8855_MIRROR_EN		BIT(7)
+#define   AN8855_MIRROR_PORT		GENMASK(4, 0)
+
+/* Registers for BPDU and PAE frame control*/
+#define AN8855_BPC			0x102000d0
+#define   AN8855_BPDU_MANG_FR		BIT(14)
+#define   AN8855_BPDU_BPDU_FR		BIT(12)
+#define   AN8855_BPDU_EG_TAG		GENMASK(11, 9)
+#define   AN8855_BPDU_LKY_VLAN		BIT(8)
+#define   AN8855_BPDU_PRI_HIGH		BIT(7)
+#define   AN8855_BPDU_MIR		GENMASK(4, 3)
+#define   AN8855_BPDU_PORT_FW		GENMASK(2, 0)
+
+/* Registers for IP Unknown Multicast Forward control */
+#define AN8855_UNIPMF			0x102000dc
+
+enum an8855_bpdu_port_fw {
+	AN8855_BPDU_FOLLOW_MFC = 0,
+	AN8855_BPDU_CPU_EXCLUDE = 4,
+	AN8855_BPDU_CPU_INCLUDE = 5,
+	AN8855_BPDU_CPU_ONLY = 6,
+	AN8855_BPDU_DROP = 7,
+};
+
+/* Register for address table control */
+#define AN8855_ATC			0x10200300
+#define   AN8855_ATC_BUSY		BIT(31)
+#define   AN8855_ATC_HASH		GENMASK(24, 16)
+#define   AN8855_ATC_HIT		GENMASK(15, 12)
+#define   AN8855_ATC_MAT_MASK		GENMASK(11, 7)
+#define   AN8855_ATC_MAT(x)		FIELD_PREP(AN8855_ATC_MAT_MASK, x)
+#define   AN8855_ATC_SAT		GENMASK(5, 4)
+#define   AN8855_ATC_CMD		GENMASK(2, 0)
+
+enum an8855_fdb_mat_cmds {
+	AND8855_FDB_MAT_ALL = 0,
+	AND8855_FDB_MAT_MAC, /* All MAC address */
+	AND8855_FDB_MAT_DYNAMIC_MAC, /* All Dynamic MAC address */
+	AND8855_FDB_MAT_STATIC_MAC, /* All Static Mac Address */
+	AND8855_FDB_MAT_DIP, /* All DIP/GA address */
+	AND8855_FDB_MAT_DIP_IPV4, /* All DIP/GA IPv4 address */
+	AND8855_FDB_MAT_DIP_IPV6, /* All DIP/GA IPv6 address */
+	AND8855_FDB_MAT_DIP_SIP, /* All DIP_SIP address */
+	AND8855_FDB_MAT_DIP_SIP_IPV4, /* All DIP_SIP IPv4 address */
+	AND8855_FDB_MAT_DIP_SIP_IPV6, /* All DIP_SIP IPv6 address */
+	AND8855_FDB_MAT_MAC_CVID, /* All MAC address with CVID */
+	AND8855_FDB_MAT_MAC_FID, /* All MAC address with Filter ID */
+	AND8855_FDB_MAT_MAC_PORT, /* All MAC address with port */
+	AND8855_FDB_MAT_DIP_SIP_DIP_IPV4, /* All DIP_SIP address with DIP_IPV4 */
+	AND8855_FDB_MAT_DIP_SIP_SIP_IPV4, /* All DIP_SIP address with SIP_IPV4 */
+	AND8855_FDB_MAT_DIP_SIP_DIP_IPV6, /* All DIP_SIP address with DIP_IPV6 */
+	AND8855_FDB_MAT_DIP_SIP_SIP_IPV6, /* All DIP_SIP address with SIP_IPV6 */
+	/* All MAC address with MAC type (dynamic or static) with CVID */
+	AND8855_FDB_MAT_MAC_TYPE_CVID,
+	/* All MAC address with MAC type (dynamic or static) with Filter ID */
+	AND8855_FDB_MAT_MAC_TYPE_FID,
+	/* All MAC address with MAC type (dynamic or static) with port */
+	AND8855_FDB_MAT_MAC_TYPE_PORT,
+};
+
+enum an8855_fdb_cmds {
+	AN8855_FDB_READ = 0,
+	AN8855_FDB_WRITE = 1,
+	AN8855_FDB_FLUSH = 2,
+	AN8855_FDB_START = 4,
+	AN8855_FDB_NEXT = 5,
+};
+
+/* Registers for address table access */
+#define AN8855_ATA1			0x10200304
+#define   AN8855_ATA1_MAC0		GENMASK(31, 24)
+#define   AN8855_ATA1_MAC1		GENMASK(23, 16)
+#define   AN8855_ATA1_MAC2		GENMASK(15, 8)
+#define   AN8855_ATA1_MAC3		GENMASK(7, 0)
+#define AN8855_ATA2			0x10200308
+#define   AN8855_ATA2_MAC4		GENMASK(31, 24)
+#define   AN8855_ATA2_MAC5		GENMASK(23, 16)
+#define   AN8855_ATA2_UNAUTH		BIT(10)
+#define   AN8855_ATA2_TYPE		BIT(9) /* 1: dynamic, 0: static */
+#define   AN8855_ATA2_AGE		GENMASK(8, 0)
+
+/* Register for address table write data */
+#define AN8855_ATWD			0x10200324
+#define   AN8855_ATWD_FID		GENMASK(31, 28)
+#define   AN8855_ATWD_VID		GENMASK(27, 16)
+#define   AN8855_ATWD_IVL		BIT(15)
+#define   AN8855_ATWD_EG_TAG		GENMASK(14, 12)
+#define   AN8855_ATWD_SA_MIR		GENMASK(9, 8)
+#define   AN8855_ATWD_SA_FWD		GENMASK(7, 5)
+#define   AN8855_ATWD_UPRI		GENMASK(4, 2)
+#define   AN8855_ATWD_LEAKY		BIT(1)
+#define   AN8855_ATWD_VLD		BIT(0) /* vid LOAD */
+#define AN8855_ATWD2			0x10200328
+#define   AN8855_ATWD2_PORT		GENMASK(7, 0)
+
+/* Registers for table search read address */
+#define AN8855_ATRDS			0x10200330
+#define   AN8855_ATRD_SEL		GENMASK(1, 0)
+#define AN8855_ATRD0			0x10200334
+#define   AN8855_ATRD0_FID		GENMASK(28, 25)
+#define   AN8855_ATRD0_VID		GENMASK(21, 10)
+#define   AN8855_ATRD0_IVL		BIT(9)
+#define   AN8855_ATRD0_TYPE		GENMASK(4, 3)
+#define   AN8855_ATRD0_ARP		GENMASK(2, 1)
+#define   AN8855_ATRD0_LIVE		BIT(0)
+#define AN8855_ATRD1			0x10200338
+#define   AN8855_ATRD1_MAC4		GENMASK(31, 24)
+#define   AN8855_ATRD1_MAC5		GENMASK(23, 16)
+#define   AN8855_ATRD1_AGING		GENMASK(11, 3)
+#define AN8855_ATRD2			0x1020033c
+#define   AN8855_ATRD2_MAC0		GENMASK(31, 24)
+#define   AN8855_ATRD2_MAC1		GENMASK(23, 16)
+#define   AN8855_ATRD2_MAC2		GENMASK(15, 8)
+#define   AN8855_ATRD2_MAC3		GENMASK(7, 0)
+#define AN8855_ATRD3			0x10200340
+#define   AN8855_ATRD3_PORTMASK		GENMASK(7, 0)
+
+enum an8855_fdb_type {
+	AN8855_MAC_TB_TY_MAC = 0,
+	AN8855_MAC_TB_TY_DIP = 1,
+	AN8855_MAC_TB_TY_DIP_SIP = 2,
+};
+
+/* Register for vlan table control */
+#define AN8855_VTCR			0x10200600
+#define   AN8855_VTCR_BUSY		BIT(31)
+#define   AN8855_VTCR_FUNC		GENMASK(15, 12)
+#define   AN8855_VTCR_VID		GENMASK(11, 0)
+
+enum an8855_vlan_cmd {
+	/* Read/Write the specified VID entry from VAWD register based
+	 * on VID.
+	 */
+	AN8855_VTCR_RD_VID = 0,
+	AN8855_VTCR_WR_VID = 1,
+};
+
+/* Register for setup vlan write data */
+#define AN8855_VAWD0			0x10200604
+/* VLAN Member Control */
+#define   AN8855_VA0_PORT		GENMASK(31, 26)
+/* Egress Tag Control */
+#define   AN8855_VA0_ETAG		GENMASK(23, 12)
+#define   AN8855_VA0_ETAG_PORT		GENMASK(13, 12)
+#define   AN8855_VA0_ETAG_PORT_SHIFT(port) ((port) * 2)
+#define   AN8855_VA0_ETAG_PORT_MASK(port) (AN8855_VA0_ETAG_PORT << \
+						AN8855_VA0_ETAG_PORT_SHIFT(port))
+#define   AN8855_VA0_ETAG_PORT_VAL(port, val) (FIELD_PREP(AN8855_VA0_ETAG_PORT, (val)) << \
+						AN8855_VA0_ETAG_PORT_SHIFT(port))
+#define   AN8855_VA0_EG_CON		BIT(11)
+#define   AN8855_VA0_VTAG_EN		BIT(10) /* Per VLAN Egress Tag Control */
+#define   AN8855_VA0_IVL_MAC		BIT(5) /* Independent VLAN Learning */
+#define	  AN8855_VA0_FID		GENMASK(4, 1)
+#define   AN8855_VA0_VLAN_VALID		BIT(0) /* VLAN Entry Valid */
+#define AN8855_VAWD1			0x10200608
+#define   AN8855_VA1_PORT_STAG		BIT(1)
+
+enum an8855_fid {
+	AN8855_FID_STANDALONE = 0,
+	AN8855_FID_BRIDGED = 1,
+};
+
+/* Same register field of VAWD0 */
+#define AN8855_VARD0			0x10200618
+
+enum an8855_vlan_egress_attr {
+	AN8855_VLAN_EGRESS_UNTAG = 0,
+	AN8855_VLAN_EGRESS_TAG = 2,
+	AN8855_VLAN_EGRESS_STACK = 3,
+};
+
+/* Register for port STP state control */
+#define AN8855_SSP_P(x)			(0x10208000 + ((x) * 0x200))
+/* Up to 16 FID supported, each with the same mask */
+#define	  AN8855_FID_PST		GENMASK(1, 0)
+#define   AN8855_FID_PST_SHIFT(fid)	(2 * (fid))
+#define   AN8855_FID_PST_MASK(fid)	(AN8855_FID_PST << \
+						AN8855_FID_PST_SHIFT(fid))
+#define   AN8855_FID_PST_VAL(fid, val)	(FIELD_PREP(AN8855_FID_PST, (val)) << \
+						AN8855_FID_PST_SHIFT(fid))
+
+enum an8855_stp_state {
+	AN8855_STP_DISABLED = 0,
+	AN8855_STP_BLOCKING = 1,
+	AN8855_STP_LISTENING = AN8855_STP_BLOCKING,
+	AN8855_STP_LEARNING = 2,
+	AN8855_STP_FORWARDING = 3
+};
+
+/* Register for port control */
+#define AN8855_PCR_P(x)			(0x10208004 + ((x) * 0x200))
+#define   AN8855_EG_TAG			GENMASK(29, 28)
+#define   AN8855_PORT_PRI		GENMASK(26, 24)
+#define   AN8855_PORT_TX_MIR		BIT(20)
+#define   AN8855_PORT_RX_MIR		BIT(16)
+#define   AN8855_PORT_VLAN		GENMASK(1, 0)
+
+enum an8855_port_mode {
+	/* Port Matrix Mode: Frames are forwarded by the PCR_MATRIX members. */
+	AN8855_PORT_MATRIX_MODE = 0,
+
+	/* Fallback Mode: Forward received frames with ingress ports that do
+	 * not belong to the VLAN member. Frames whose VID is not listed on
+	 * the VLAN table are forwarded by the PCR_MATRIX members.
+	 */
+	AN8855_PORT_FALLBACK_MODE = 1,
+
+	/* Check Mode: Forward received frames whose ingress do not
+	 * belong to the VLAN member. Discard frames if VID ismiddes on the
+	 * VLAN table.
+	 */
+	AN8855_PORT_CHECK_MODE = 2,
+
+	/* Security Mode: Discard any frame due to ingress membership
+	 * violation or VID missed on the VLAN table.
+	 */
+	AN8855_PORT_SECURITY_MODE = 3,
+};
+
+/* Register for port security control */
+#define AN8855_PSC_P(x)			(0x1020800c + ((x) * 0x200))
+#define   AN8855_SA_DIS			BIT(4)
+
+/* Register for port vlan control */
+#define AN8855_PVC_P(x)			(0x10208010 + ((x) * 0x200))
+#define   AN8855_PORT_SPEC_REPLACE_MODE	BIT(11)
+#define   AN8855_PVC_EG_TAG		GENMASK(10, 8)
+#define   AN8855_VLAN_ATTR		GENMASK(7, 6)
+#define   AN8855_PORT_SPEC_TAG		BIT(5)
+#define   AN8855_ACC_FRM		GENMASK(1, 0)
+
+enum an8855_vlan_port_eg_tag {
+	AN8855_VLAN_EG_DISABLED = 0,
+	AN8855_VLAN_EG_CONSISTENT = 1,
+	AN8855_VLAN_EG_UNTAGGED = 4,
+	AN8855_VLAN_EG_SWAP = 5,
+	AN8855_VLAN_EG_TAGGED = 6,
+	AN8855_VLAN_EG_STACK = 7,
+};
+
+enum an8855_vlan_port_attr {
+	AN8855_VLAN_USER = 0,
+	AN8855_VLAN_STACK = 1,
+	AN8855_VLAN_TRANSPARENT = 3,
+};
+
+enum an8855_vlan_port_acc_frm {
+	AN8855_VLAN_ACC_ALL = 0,
+	AN8855_VLAN_ACC_TAGGED = 1,
+	AN8855_VLAN_ACC_UNTAGGED = 2,
+};
+
+#define AN8855_PPBV1_P(x)		(0x10208014 + ((x) * 0x200))
+#define   AN8855_PPBV_G0_PORT_VID	GENMASK(11, 0)
+
+#define AN8855_PORTMATRIX_P(x)		(0x10208044 + ((x) * 0x200))
+#define   AN8855_PORTMATRIX		GENMASK(5, 0)
+/* Port matrix without the CPU port that should never be removed */
+#define   AN8855_USER_PORTMATRIX	GENMASK(4, 0)
+
+/* Register for port PVID */
+#define AN8855_PVID_P(x)		(0x10208048 + ((x) * 0x200))
+#define   AN8855_G0_PORT_VID		GENMASK(11, 0)
+
+/* Register for port MAC control register */
+#define AN8855_PMCR_P(x)		(0x10210000 + ((x) * 0x200))
+#define   AN8855_PMCR_FORCE_MODE	BIT(31)
+#define   AN8855_PMCR_FORCE_SPEED	GENMASK(30, 28)
+#define   AN8855_PMCR_FORCE_SPEED_5000	FIELD_PREP_CONST(AN8855_PMCR_FORCE_SPEED, 0x4)
+#define   AN8855_PMCR_FORCE_SPEED_2500	FIELD_PREP_CONST(AN8855_PMCR_FORCE_SPEED, 0x3)
+#define   AN8855_PMCR_FORCE_SPEED_1000	FIELD_PREP_CONST(AN8855_PMCR_FORCE_SPEED, 0x2)
+#define   AN8855_PMCR_FORCE_SPEED_100	FIELD_PREP_CONST(AN8855_PMCR_FORCE_SPEED, 0x1)
+#define   AN8855_PMCR_FORCE_SPEED_10	FIELD_PREP_CONST(AN8855_PMCR_FORCE_SPEED, 0x1)
+#define   AN8855_PMCR_FORCE_FDX		BIT(25)
+#define   AN8855_PMCR_FORCE_LNK		BIT(24)
+#define   AN8855_PMCR_IFG_XMIT		GENMASK(21, 20)
+#define   AN8855_PMCR_EXT_PHY		BIT(19)
+#define   AN8855_PMCR_MAC_MODE		BIT(18)
+#define   AN8855_PMCR_TX_EN		BIT(16)
+#define   AN8855_PMCR_RX_EN		BIT(15)
+#define   AN8855_PMCR_BACKOFF_EN	BIT(12)
+#define   AN8855_PMCR_BACKPR_EN		BIT(11)
+#define   AN8855_PMCR_FORCE_EEE5G	BIT(9)
+#define   AN8855_PMCR_FORCE_EEE2P5G	BIT(8)
+#define   AN8855_PMCR_FORCE_EEE1G	BIT(7)
+#define   AN8855_PMCR_FORCE_EEE100	BIT(6)
+#define   AN8855_PMCR_TX_FC_EN		BIT(5)
+#define   AN8855_PMCR_RX_FC_EN		BIT(4)
+
+#define AN8855_PMSR_P(x)		(0x10210010 + (x) * 0x200)
+#define   AN8855_PMSR_SPEED		GENMASK(30, 28)
+#define   AN8855_PMSR_SPEED_5000	FIELD_PREP_CONST(AN8855_PMSR_SPEED, 0x4)
+#define   AN8855_PMSR_SPEED_2500	FIELD_PREP_CONST(AN8855_PMSR_SPEED, 0x3)
+#define   AN8855_PMSR_SPEED_1000	FIELD_PREP_CONST(AN8855_PMSR_SPEED, 0x2)
+#define   AN8855_PMSR_SPEED_100		FIELD_PREP_CONST(AN8855_PMSR_SPEED, 0x1)
+#define   AN8855_PMSR_SPEED_10		FIELD_PREP_CONST(AN8855_PMSR_SPEED, 0x0)
+#define   AN8855_PMSR_DPX		BIT(25)
+#define   AN8855_PMSR_LNK		BIT(24)
+#define   AN8855_PMSR_EEE1G		BIT(7)
+#define   AN8855_PMSR_EEE100M		BIT(6)
+#define   AN8855_PMSR_RX_FC		BIT(5)
+#define   AN8855_PMSR_TX_FC		BIT(4)
+
+#define AN8855_PMEEECR_P(x)		(0x10210004 + (x) * 0x200)
+#define   AN8855_LPI_MODE_EN		BIT(31)
+#define   AN8855_WAKEUP_TIME_2500	GENMASK(23, 16)
+#define   AN8855_WAKEUP_TIME_1000	GENMASK(15, 8)
+#define   AN8855_WAKEUP_TIME_100	GENMASK(7, 0)
+#define AN8855_PMEEECR2_P(x)		(0x10210008 + (x) * 0x200)
+#define   AN8855_WAKEUP_TIME_5000	GENMASK(7, 0)
+
+#define AN8855_GMACCR			0x10213e00
+#define   AN8855_MAX_RX_JUMBO		GENMASK(7, 4)
+/* 2K for 0x0, 0x1, 0x2 */
+#define   AN8855_MAX_RX_JUMBO_2K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x0)
+#define   AN8855_MAX_RX_JUMBO_3K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x3)
+#define   AN8855_MAX_RX_JUMBO_4K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x4)
+#define   AN8855_MAX_RX_JUMBO_5K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x5)
+#define   AN8855_MAX_RX_JUMBO_6K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x6)
+#define   AN8855_MAX_RX_JUMBO_7K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x7)
+#define   AN8855_MAX_RX_JUMBO_8K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x8)
+#define   AN8855_MAX_RX_JUMBO_9K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0x9)
+#define   AN8855_MAX_RX_JUMBO_12K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0xa)
+#define   AN8855_MAX_RX_JUMBO_15K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0xb)
+#define   AN8855_MAX_RX_JUMBO_16K	FIELD_PREP_CONST(AN8855_MAX_RX_JUMBO, 0xc)
+#define   AN8855_MAX_RX_PKT_LEN		GENMASK(1, 0)
+#define   AN8855_MAX_RX_PKT_1518_1522	FIELD_PREP_CONST(AN8855_MAX_RX_PKT_LEN, 0x0)
+#define   AN8855_MAX_RX_PKT_1536	FIELD_PREP_CONST(AN8855_MAX_RX_PKT_LEN, 0x1)
+#define   AN8855_MAX_RX_PKT_1552	FIELD_PREP_CONST(AN8855_MAX_RX_PKT_LEN, 0x2)
+#define   AN8855_MAX_RX_PKT_JUMBO	FIELD_PREP_CONST(AN8855_MAX_RX_PKT_LEN, 0x3)
+
+#define AN8855_CKGCR			0x10213e1c
+#define   AN8855_LPI_TXIDLE_THD_MASK	GENMASK(31, 14)
+#define   AN8855_CKG_LNKDN_PORT_STOP	BIT(1)
+#define   AN8855_CKG_LNKDN_GLB_STOP	BIT(0)
+
+/* Register for MIB */
+#define AN8855_PORT_MIB_COUNTER(x)	(0x10214000 + (x) * 0x200)
+/* Each define is an offset of AN8855_PORT_MIB_COUNTER */
+#define   AN8855_PORT_MIB_TX_DROP	0x00
+#define   AN8855_PORT_MIB_TX_CRC_ERR	0x04
+#define   AN8855_PORT_MIB_TX_UNICAST	0x08
+#define   AN8855_PORT_MIB_TX_MULTICAST	0x0c
+#define   AN8855_PORT_MIB_TX_BROADCAST	0x10
+#define   AN8855_PORT_MIB_TX_COLLISION	0x14
+#define   AN8855_PORT_MIB_TX_SINGLE_COLLISION 0x18
+#define   AN8855_PORT_MIB_TX_MULTIPLE_COLLISION 0x1c
+#define   AN8855_PORT_MIB_TX_DEFERRED	0x20
+#define   AN8855_PORT_MIB_TX_LATE_COLLISION 0x24
+#define   AN8855_PORT_MIB_TX_EXCESSIVE_COLLISION 0x28
+#define   AN8855_PORT_MIB_TX_PAUSE	0x2c
+#define   AN8855_PORT_MIB_TX_PKT_SZ_64	0x30
+#define   AN8855_PORT_MIB_TX_PKT_SZ_65_TO_127 0x34
+#define   AN8855_PORT_MIB_TX_PKT_SZ_128_TO_255 0x38
+#define   AN8855_PORT_MIB_TX_PKT_SZ_256_TO_511 0x3
+#define   AN8855_PORT_MIB_TX_PKT_SZ_512_TO_1023 0x40
+#define   AN8855_PORT_MIB_TX_PKT_SZ_1024_TO_1518 0x44
+#define   AN8855_PORT_MIB_TX_PKT_SZ_1519_TO_MAX 0x48
+#define   AN8855_PORT_MIB_TX_BYTES	0x4c /* 64 bytes */
+#define   AN8855_PORT_MIB_TX_OVERSIZE_DROP 0x54
+#define   AN8855_PORT_MIB_TX_BAD_PKT_BYTES 0x58 /* 64 bytes */
+#define   AN8855_PORT_MIB_RX_DROP	0x80
+#define   AN8855_PORT_MIB_RX_FILTERING	0x84
+#define   AN8855_PORT_MIB_RX_UNICAST	0x88
+#define   AN8855_PORT_MIB_RX_MULTICAST	0x8c
+#define   AN8855_PORT_MIB_RX_BROADCAST	0x90
+#define   AN8855_PORT_MIB_RX_ALIGN_ERR	0x94
+#define   AN8855_PORT_MIB_RX_CRC_ERR	0x98
+#define   AN8855_PORT_MIB_RX_UNDER_SIZE_ERR 0x9c
+#define   AN8855_PORT_MIB_RX_FRAG_ERR	0xa0
+#define   AN8855_PORT_MIB_RX_OVER_SZ_ERR 0xa4
+#define   AN8855_PORT_MIB_RX_JABBER_ERR	0xa8
+#define   AN8855_PORT_MIB_RX_PAUSE	0xac
+#define   AN8855_PORT_MIB_RX_PKT_SZ_64	0xb0
+#define   AN8855_PORT_MIB_RX_PKT_SZ_65_TO_127 0xb4
+#define   AN8855_PORT_MIB_RX_PKT_SZ_128_TO_255 0xb8
+#define   AN8855_PORT_MIB_RX_PKT_SZ_256_TO_511 0xbc
+#define   AN8855_PORT_MIB_RX_PKT_SZ_512_TO_1023 0xc0
+#define   AN8855_PORT_MIB_RX_PKT_SZ_1024_TO_1518 0xc4
+#define   AN8855_PORT_MIB_RX_PKT_SZ_1519_TO_MAX 0xc8
+#define   AN8855_PORT_MIB_RX_BYTES	0xcc /* 64 bytes */
+#define   AN8855_PORT_MIB_RX_CTRL_DROP	0xd4
+#define   AN8855_PORT_MIB_RX_INGRESS_DROP 0xd8
+#define   AN8855_PORT_MIB_RX_ARL_DROP	0xdc
+#define   AN8855_PORT_MIB_FLOW_CONTROL_DROP 0xe0
+#define   AN8855_PORT_MIB_WRED_DROP	0xe4
+#define   AN8855_PORT_MIB_MIRROR_DROP	0xe8
+#define   AN8855_PORT_MIB_RX_BAD_PKT_BYTES 0xec /* 64 bytes */
+#define   AN8855_PORT_MIB_RXS_FLOW_SAMPLING_PKT_DROP 0xf4
+#define   AN8855_PORT_MIB_RXS_FLOW_TOTAL_PKT_DROP 0xf8
+#define   AN8855_PORT_MIB_PORT_CONTROL_DROP 0xfc
+#define AN8855_MIB_CCR			0x10213e30
+#define   AN8855_CCR_MIB_ENABLE		BIT(31)
+#define   AN8855_CCR_RX_OCT_CNT_GOOD	BIT(7)
+#define   AN8855_CCR_RX_OCT_CNT_BAD	BIT(6)
+#define   AN8855_CCR_TX_OCT_CNT_GOOD	BIT(5)
+#define   AN8855_CCR_TX_OCT_CNT_BAD	BIT(4)
+#define   AN8855_CCR_RX_OCT_CNT_GOOD_2	BIT(3)
+#define   AN8855_CCR_RX_OCT_CNT_BAD_2	BIT(2)
+#define   AN8855_CCR_TX_OCT_CNT_GOOD_2	BIT(1)
+#define   AN8855_CCR_TX_OCT_CNT_BAD_2	BIT(0)
+#define   AN8855_CCR_MIB_ACTIVATE	(AN8855_CCR_MIB_ENABLE | \
+					 AN8855_CCR_RX_OCT_CNT_GOOD | \
+					 AN8855_CCR_RX_OCT_CNT_BAD | \
+					 AN8855_CCR_TX_OCT_CNT_GOOD | \
+					 AN8855_CCR_TX_OCT_CNT_BAD | \
+					 AN8855_CCR_RX_OCT_CNT_BAD_2 | \
+					 AN8855_CCR_TX_OCT_CNT_BAD_2)
+#define AN8855_MIB_CLR			0x10213e34
+#define   AN8855_MIB_PORT6_CLR		BIT(6)
+#define   AN8855_MIB_PORT5_CLR		BIT(5)
+#define   AN8855_MIB_PORT4_CLR		BIT(4)
+#define   AN8855_MIB_PORT3_CLR		BIT(3)
+#define   AN8855_MIB_PORT2_CLR		BIT(2)
+#define   AN8855_MIB_PORT1_CLR		BIT(1)
+#define   AN8855_MIB_PORT0_CLR		BIT(0)
+
+/* HSGMII/SGMII Configuration register */
+/*	AN8855_HSGMII_AN_CSR_BASE	0x10220000 */
+#define AN8855_SGMII_REG_AN0		0x10220000
+/*        AN8855_SGMII_AN_ENABLE	BMCR_ANENABLE */
+/*        AN8855_SGMII_AN_RESTART	BMCR_ANRESTART */
+#define AN8855_SGMII_REG_AN_13		0x10220034
+#define   AN8855_SGMII_REMOTE_FAULT_DIS	BIT(8)
+#define   AN8855_SGMII_IF_MODE		GENMASK(5, 0)
+#define AN8855_SGMII_REG_AN_FORCE_CL37	0x10220060
+#define   AN8855_RG_FORCE_AN_DONE	BIT(0)
+
+/*	AN8855_HSGMII_CSR_PCS_BASE	0x10220000 */
+#define AN8855_RG_HSGMII_PCS_CTROL_1	0x10220a00
+#define   AN8855_RG_TBI_10B_MODE	BIT(30)
+#define AN8855_RG_AN_SGMII_MODE_FORCE	0x10220a24
+#define   AN8855_RG_FORCE_CUR_SGMII_MODE GENMASK(5, 4)
+#define   AN8855_RG_FORCE_CUR_SGMII_SEL	BIT(0)
+
+/*	AN8855_MULTI_SGMII_CSR_BASE	0x10224000 */
+#define AN8855_SGMII_STS_CTRL_0		0x10224018
+#define   AN8855_RG_LINK_MODE_P0	GENMASK(5, 4)
+#define   AN8855_RG_LINK_MODE_P0_SPEED_2500 FIELD_PREP_CONST(AN8855_RG_LINK_MODE_P0, 0x3)
+#define   AN8855_RG_LINK_MODE_P0_SPEED_1000 FIELD_PREP_CONST(AN8855_RG_LINK_MODE_P0, 0x2)
+#define   AN8855_RG_LINK_MODE_P0_SPEED_100 FIELD_PREP_CONST(AN8855_RG_LINK_MODE_P0, 0x1)
+#define   AN8855_RG_LINK_MODE_P0_SPEED_10 FIELD_PREP_CONST(AN8855_RG_LINK_MODE_P0, 0x0)
+#define   AN8855_RG_FORCE_SPD_MODE_P0	BIT(2)
+#define AN8855_MSG_RX_CTRL_0		0x10224100
+#define AN8855_MSG_RX_LIK_STS_0		0x10224514
+#define   AN8855_RG_DPX_STS_P3		BIT(24)
+#define   AN8855_RG_DPX_STS_P2		BIT(16)
+#define   AN8855_RG_EEE1G_STS_P1	BIT(12)
+#define   AN8855_RG_DPX_STS_P1		BIT(8)
+#define   AN8855_RG_TXFC_STS_P0		BIT(2)
+#define   AN8855_RG_RXFC_STS_P0		BIT(1)
+#define   AN8855_RG_DPX_STS_P0		BIT(0)
+#define AN8855_MSG_RX_LIK_STS_2		0x1022451c
+#define   AN8855_RG_RXFC_AN_BYPASS_P3	BIT(11)
+#define   AN8855_RG_RXFC_AN_BYPASS_P2	BIT(10)
+#define   AN8855_RG_RXFC_AN_BYPASS_P1	BIT(9)
+#define   AN8855_RG_TXFC_AN_BYPASS_P3	BIT(7)
+#define   AN8855_RG_TXFC_AN_BYPASS_P2	BIT(6)
+#define   AN8855_RG_TXFC_AN_BYPASS_P1	BIT(5)
+#define   AN8855_RG_DPX_AN_BYPASS_P3	BIT(3)
+#define   AN8855_RG_DPX_AN_BYPASS_P2	BIT(2)
+#define   AN8855_RG_DPX_AN_BYPASS_P1	BIT(1)
+#define   AN8855_RG_DPX_AN_BYPASS_P0	BIT(0)
+#define AN8855_PHY_RX_FORCE_CTRL_0	0x10224520
+#define   AN8855_RG_FORCE_TXC_SEL	BIT(4)
+
+/*	AN8855_XFI_CSR_PCS_BASE		0x10225000 */
+#define AN8855_RG_USXGMII_AN_CONTROL_0	0x10225bf8
+
+/*	AN8855_MULTI_PHY_RA_CSR_BASE	0x10226000 */
+#define AN8855_RG_RATE_ADAPT_CTRL_0	0x10226000
+#define   AN8855_RG_RATE_ADAPT_RX_BYPASS BIT(27)
+#define   AN8855_RG_RATE_ADAPT_TX_BYPASS BIT(26)
+#define   AN8855_RG_RATE_ADAPT_RX_EN	BIT(4)
+#define   AN8855_RG_RATE_ADAPT_TX_EN	BIT(0)
+#define AN8855_RATE_ADP_P0_CTRL_0	0x10226100
+#define   AN8855_RG_P0_DIS_MII_MODE	BIT(31)
+#define   AN8855_RG_P0_MII_MODE		BIT(28)
+#define   AN8855_RG_P0_MII_RA_RX_EN	BIT(3)
+#define   AN8855_RG_P0_MII_RA_TX_EN	BIT(2)
+#define   AN8855_RG_P0_MII_RA_RX_MODE	BIT(1)
+#define   AN8855_RG_P0_MII_RA_TX_MODE	BIT(0)
+#define AN8855_MII_RA_AN_ENABLE		0x10226300
+#define   AN8855_RG_P0_RA_AN_EN		BIT(0)
+
+/*	AN8855_QP_DIG_CSR_BASE		0x1022a000 */
+#define AN8855_QP_CK_RST_CTRL_4		0x1022a310
+#define AN8855_QP_DIG_MODE_CTRL_0	0x1022a324
+#define   AN8855_RG_SGMII_MODE		GENMASK(5, 4)
+#define   AN8855_RG_SGMII_AN_EN		BIT(0)
+#define AN8855_QP_DIG_MODE_CTRL_1	0x1022a330
+#define   AN8855_RG_TPHY_SPEED		GENMASK(3, 2)
+
+/*	AN8855_SERDES_WRAPPER_BASE	0x1022c000 */
+#define AN8855_USGMII_CTRL_0		0x1022c000
+
+/*	AN8855_QP_PMA_TOP_BASE		0x1022e000 */
+#define AN8855_PON_RXFEDIG_CTRL_0	0x1022e100
+#define   AN8855_RG_QP_EQ_RX500M_CK_SEL	BIT(12)
+#define AN8855_PON_RXFEDIG_CTRL_9	0x1022e124
+#define   AN8855_RG_QP_EQ_LEQOSC_DLYCNT	GENMASK(2, 0)
+
+#define AN8855_SS_LCPLL_PWCTL_SETTING_2	0x1022e208
+#define   AN8855_RG_NCPO_ANA_MSB	GENMASK(17, 16)
+#define AN8855_SS_LCPLL_TDC_FLT_2	0x1022e230
+#define   AN8855_RG_LCPLL_NCPO_VALUE	GENMASK(30, 0)
+#define AN8855_SS_LCPLL_TDC_FLT_5	0x1022e23c
+#define   AN8855_RG_LCPLL_NCPO_CHG	BIT(24)
+#define AN8855_SS_LCPLL_TDC_PCW_1	0x1022e248
+#define  AN8855_RG_LCPLL_PON_HRDDS_PCW_NCPO_GPON GENMASK(30, 0)
+#define AN8855_INTF_CTRL_8		0x1022e320
+#define AN8855_INTF_CTRL_9		0x1022e324
+#define AN8855_INTF_CTRL_10		0x1022e328
+#define   AN8855_RG_DA_QP_TX_FIR_C2_SEL	BIT(29)
+#define   AN8855_RG_DA_QP_TX_FIR_C2_FORCE GENMASK(28, 24)
+#define   AN8855_RG_DA_QP_TX_FIR_C1_SEL	BIT(21)
+#define   AN8855_RG_DA_QP_TX_FIR_C1_FORCE GENMASK(20, 16)
+#define AN8855_INTF_CTRL_11		0x1022e32c
+#define   AN8855_RG_DA_QP_TX_FIR_C0B_SEL BIT(6)
+#define   AN8855_RG_DA_QP_TX_FIR_C0B_FORCE GENMASK(5, 0)
+#define AN8855_PLL_CTRL_0		0x1022e400
+#define   AN8855_RG_PHYA_AUTO_INIT	BIT(0)
+#define AN8855_PLL_CTRL_2		0x1022e408
+#define   AN8855_RG_DA_QP_PLL_SDM_IFM_INTF BIT(30)
+#define   AN8855_RG_DA_QP_PLL_RICO_SEL_INTF BIT(29)
+#define   AN8855_RG_DA_QP_PLL_POSTDIV_EN_INTF BIT(28)
+#define   AN8855_RG_DA_QP_PLL_PHY_CK_EN_INTF BIT(27)
+#define   AN8855_RG_DA_QP_PLL_PFD_OFFSET_EN_INTRF BIT(26)
+#define   AN8855_RG_DA_QP_PLL_PFD_OFFSET_INTF GENMASK(25, 24)
+#define   AN8855_RG_DA_QP_PLL_PCK_SEL_INTF BIT(22)
+#define   AN8855_RG_DA_QP_PLL_KBAND_PREDIV_INTF GENMASK(21, 20)
+#define   AN8855_RG_DA_QP_PLL_IR_INTF	GENMASK(19, 16)
+#define   AN8855_RG_DA_QP_PLL_ICOIQ_EN_INTF BIT(14)
+#define   AN8855_RG_DA_QP_PLL_FBKSEL_INTF GENMASK(13, 12)
+#define   AN8855_RG_DA_QP_PLL_BR_INTF	GENMASK(10, 8)
+#define   AN8855_RG_DA_QP_PLL_BPD_INTF	GENMASK(7, 6)
+#define   AN8855_RG_DA_QP_PLL_BPA_INTF	GENMASK(4, 2)
+#define   AN8855_RG_DA_QP_PLL_BC_INTF	GENMASK(1, 0)
+#define AN8855_PLL_CTRL_3		0x1022e40c
+#define   AN8855_RG_DA_QP_PLL_SSC_PERIOD_INTF GENMASK(31, 16)
+#define   AN8855_RG_DA_QP_PLL_SSC_DELTA_INTF GENMASK(15, 0)
+#define AN8855_PLL_CTRL_4		0x1022e410
+#define   AN8855_RG_DA_QP_PLL_SDM_HREN_INTF GENMASK(4, 3)
+#define   AN8855_RG_DA_QP_PLL_ICOLP_EN_INTF BIT(2)
+#define   AN8855_RG_DA_QP_PLL_SSC_DIR_DLY_INTF GENMASK(1, 0)
+#define AN8855_PLL_CK_CTRL_0		0x1022e414
+#define   AN8855_RG_DA_QP_PLL_TDC_TXCK_SEL_INTF BIT(9)
+#define   AN8855_RG_DA_QP_PLL_SDM_DI_EN_INTF BIT(8)
+#define AN8855_RX_DLY_0			0x1022e614
+#define   AN8855_RG_QP_RX_SAOSC_EN_H_DLY GENMASK(13, 8)
+#define   AN8855_RG_QP_RX_PI_CAL_EN_H_DLY GENMASK(7, 0)
+#define AN8855_RX_CTRL_2		0x1022e630
+#define   AN8855_RG_QP_RX_EQ_EN_H_DLY	GENMASK(28, 16)
+#define AN8855_RX_CTRL_5		0x1022e63c
+#define   AN8855_RG_FREDET_CHK_CYCLE	GENMASK(29, 10)
+#define AN8855_RX_CTRL_6		0x1022e640
+#define   AN8855_RG_FREDET_GOLDEN_CYCLE	GENMASK(19, 0)
+#define AN8855_RX_CTRL_7		0x1022e644
+#define   AN8855_RG_FREDET_TOLERATE_CYCLE GENMASK(19, 0)
+#define AN8855_RX_CTRL_8		0x1022e648
+#define   AN8855_RG_DA_QP_SAOSC_DONE_TIME GENMASK(27, 16)
+#define   AN8855_RG_DA_QP_LEQOS_EN_TIME	GENMASK(14, 0)
+#define AN8855_RX_CTRL_26		0x1022e690
+#define   AN8855_RG_QP_EQ_RETRAIN_ONLY_EN BIT(26)
+#define   AN8855_RG_LINK_NE_EN		BIT(24)
+#define   AN8855_RG_LINK_ERRO_EN	BIT(23)
+#define AN8855_RX_CTRL_42		0x1022e6d0
+#define   AN8855_RG_QP_EQ_EN_DLY	GENMASK(12, 0)
+
+/*	AN8855_QP_ANA_CSR_BASE		0x1022f000 */
+#define AN8855_RG_QP_RX_DAC_EN		0x1022f000
+#define   AN8855_RG_QP_SIGDET_HF	GENMASK(17, 16)
+#define AN8855_RG_QP_RXAFE_RESERVE	0x1022f004
+#define   AN8855_RG_QP_CDR_PD_10B_EN	BIT(11)
+#define AN8855_RG_QP_CDR_LPF_BOT_LIM	0x1022f008
+#define   AN8855_RG_QP_CDR_LPF_KP_GAIN	GENMASK(26, 24)
+#define   AN8855_RG_QP_CDR_LPF_KI_GAIN	GENMASK(22, 20)
+#define AN8855_RG_QP_CDR_LPF_MJV_LIM	0x1022f00c
+#define   AN8855_RG_QP_CDR_LPF_RATIO	GENMASK(5, 4)
+#define AN8855_RG_QP_CDR_LPF_SETVALUE	0x1022f014
+#define   AN8855_RG_QP_CDR_PR_BUF_IN_SR	GENMASK(31, 29)
+#define   AN8855_RG_QP_CDR_PR_BETA_SEL	GENMASK(28, 25)
+#define AN8855_RG_QP_CDR_PR_CKREF_DIV1	0x1022f018
+#define   AN8855_RG_QP_CDR_PR_KBAND_DIV	GENMASK(26, 24)
+#define   AN8855_RG_QP_CDR_PR_DAC_BAND	GENMASK(12, 8)
+#define AN8855_RG_QP_CDR_PR_KBAND_DIV_PCIE 0x1022f01c
+#define   AN8855_RG_QP_CDR_PR_XFICK_EN	BIT(30)
+#define   AN8855_RG_QP_CDR_PR_KBAND_PCIE_MODE BIT(6)
+#define   AN8855_RG_QP_CDR_PR_KBAND_DIV_PCIE_MASK GENMASK(5, 0)
+#define AN8855_RG_QP_CDR_FORCE_IBANDLPF_R_OFF 0x1022f020
+#define   AN8855_RG_QP_CDR_PHYCK_SEL	GENMASK(17, 16)
+#define   AN8855_RG_QP_CDR_PHYCK_RSTB	BIT(13)
+#define   AN8855_RG_QP_CDR_PHYCK_DIV	GENMASK(12, 6)
+#define AN8855_RG_QP_TX_MODE		0x1022f028
+#define   AN8855_RG_QP_TX_RESERVE	GENMASK(31, 16)
+#define   AN8855_RG_QP_TX_MODE_16B_EN	BIT(0)
+#define AN8855_RG_QP_PLL_IPLL_DIG_PWR_SEL 0x1022f03c
+#define AN8855_RG_QP_PLL_SDM_ORD	0x1022f040
+#define   AN8855_RG_QP_PLL_SSC_PHASE_INI BIT(4)
+#define   AN8855_RG_QP_PLL_SSC_TRI_EN	BIT(3)
+
+/*	AN8855_ETHER_SYS_BASE		0x1028c800 */
+#define AN8855_RG_GPHY_AFE_PWD		0x1028c840
+#define AN8855_RG_GPHY_SMI_ADDR		0x1028c848
+
+#define MIB_DESC(_s, _o, _n)	\
+	{			\
+		.size = (_s),	\
+		.offset = (_o),	\
+		.name = (_n),	\
+	}
+
+struct an8855_mib_desc {
+	unsigned int size;
+	unsigned int offset;
+	const char *name;
+};
+
+struct an8855_fdb {
+	u16 vid;
+	u8 port_mask;
+	u16 aging;
+	u8 mac[6];
+	bool noarp;
+	u8 live;
+	u8 type;
+	u8 fid;
+	u8 ivl;
+};
+
+struct an8855_priv {
+	struct dsa_switch *ds;
+	struct regmap *regmap;
+	/* Protect ATU or VLAN table access */
+	struct mutex reg_mutex;
+
+	struct phylink_pcs pcs;
+
+	u8 mirror_rx;
+	u8 mirror_tx;
+	u8 port_isolated_map;
+};
+
+#endif /* __AN8855_H */
-- 
2.48.1

[net-next PATCH v15 09/12] mfd: an8855: Add support for Airoha AN8855 Switch MFD

[Christian Marangi]

Add support for Airoha AN8855 Switch MFD that provide support for a DSA
switch and a NVMEM provider. Also provide support for the PBUS MDIO
to access the internal PHYs address from the switch registers to permit
the usage of a single regmap to handle both switch and PHYs.

An interesting HW bug wes discovered with the implementation of the MDIO
PBUS where the PHY status is not correctly detected if the PBUS is used
to read the PHY BMSR. For the only BMSR register, it's required to read
the address directly from the MDIO bus.

A check and a workaround is implemented to address this in the
regmap_read function.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/mfd/Kconfig         |  12 ++
 drivers/mfd/Makefile        |   1 +
 drivers/mfd/airoha-an8855.c | 393 ++++++++++++++++++++++++++++++++++++
 3 files changed, 406 insertions(+)
 create mode 100644 drivers/mfd/airoha-an8855.c

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 6fb3768e3d71..f2bfd6c9fc5f 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -53,6 +53,18 @@ config MFD_ALTERA_SYSMGR
 	  using regmap_mmio accesses for ARM32 parts and SMC calls to
 	  EL3 for ARM64 parts.
 
+config MFD_AIROHA_AN8855
+	tristate "Airoha AN8855 Switch Core"
+	select MFD_CORE
+	select MDIO_DEVICE
+	depends on NETDEVICES && OF
+	help
+	  Support for the Airoha AN8855 Switch Core. This is an SoC
+	  that provides various peripherals, to count, i2c, an Ethrnet
+	  Switch, a CPU timer, GPIO, eFUSE.
+
+	  Currently it provides a DSA switch and a NVMEM provider.
+
 config MFD_ACT8945A
 	tristate "Active-semi ACT8945A"
 	select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 79495f9f3457..f541b513f41e 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_MFD_88PM860X)	+= 88pm860x.o
 obj-$(CONFIG_MFD_88PM800)	+= 88pm800.o 88pm80x.o
 obj-$(CONFIG_MFD_88PM805)	+= 88pm805.o 88pm80x.o
 obj-$(CONFIG_MFD_88PM886_PMIC)	+= 88pm886.o
+obj-$(CONFIG_MFD_AIROHA_AN8855)	+= airoha-an8855.o
 obj-$(CONFIG_MFD_ACT8945A)	+= act8945a.o
 obj-$(CONFIG_MFD_SM501)		+= sm501.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835-pm.o
diff --git a/drivers/mfd/airoha-an8855.c b/drivers/mfd/airoha-an8855.c
new file mode 100644
index 000000000000..bb03a2436f25
--- /dev/null
+++ b/drivers/mfd/airoha-an8855.c
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Core driver for Airoha AN8855 Switch
+ */
+
+#include <linux/bitfield.h>
+#include <linux/dsa/an8855.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/core.h>
+#include <linux/mdio.h>
+#include <linux/mdio/mdio-regmap.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/regmap.h>
+
+/* Register for HW trap status */
+#define AN8855_HWTRAP			0x1000009c
+
+#define AN8855_CREV			0x10005000
+#define   AN8855_ID			0x8855
+
+#define AN8855_RG_GPHY_AFE_PWD		0x1028c840
+
+/* MII Registers */
+#define AN8855_PHY_SELECT_PAGE		0x1f
+#define   AN8855_PHY_PAGE		GENMASK(2, 0)
+#define   AN8855_PHY_PAGE_STANDARD	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
+#define   AN8855_PHY_PAGE_EXTENDED_1	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
+#define   AN8855_PHY_PAGE_EXTENDED_4	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x4)
+
+/* MII Registers Page 4 */
+#define AN8855_PBUS_MODE		0x10
+#define   AN8855_PBUS_MODE_ADDR_FIXED	0x0
+#define   AN8855_PBUS_MODE_ADDR_INCR	BIT(15)
+#define AN8855_PBUS_WR_ADDR_HIGH	0x11
+#define AN8855_PBUS_WR_ADDR_LOW		0x12
+#define AN8855_PBUS_WR_DATA_HIGH	0x13
+#define AN8855_PBUS_WR_DATA_LOW		0x14
+#define AN8855_PBUS_RD_ADDR_HIGH	0x15
+#define AN8855_PBUS_RD_ADDR_LOW		0x16
+#define AN8855_PBUS_RD_DATA_HIGH	0x17
+#define AN8855_PBUS_RD_DATA_LOW		0x18
+
+struct an8855_core_priv {
+	struct mii_bus *bus;
+
+	unsigned int switch_addr;
+};
+
+static const struct mfd_cell an8855_core_childs[] = {
+	{
+		.name = "an8855-efuse",
+		.of_compatible = "airoha,an8855-efuse",
+	}, {
+		.name = "an8855-switch",
+		.of_compatible = "airoha,an8855-switch",
+	}, {
+		.name = "an8855-mdio",
+		.of_compatible = "airoha,an8855-mdio",
+	}
+};
+
+static bool an8855_is_pbus_bmcr_reg(u32 reg)
+{
+	if ((reg & ~(AN8855_GPHY_PORT | AN8855_ADDR)) != AN8855_GPHY_ACCESS)
+		return false;
+
+	if ((reg & AN8855_ADDR) != FIELD_PREP_CONST(AN8855_CL22_ADDR,
+						    MII_BMSR))
+		return false;
+
+	return true;
+}
+
+/* PHY page is Global for every Switch PHY.
+ * Configure it to 4 (as Switch PAGE) and keep it that way.
+ * Page selection doesn't affect the first PHY address from 0x0 to
+ * 0xf and we use PBUS to access the PHY address.
+ */
+static int an8855_mii_set_page(struct an8855_core_priv *priv, u8 addr,
+			       u8 page) __must_hold(&priv->bus->mdio_lock)
+{
+	struct mii_bus *bus = priv->bus;
+	int ret;
+
+	ret = __mdiobus_write(bus, addr, AN8855_PHY_SELECT_PAGE, page);
+	if (ret)
+		dev_err_ratelimited(&bus->dev, "failed to set mii page\n");
+
+	return ret;
+}
+
+static int an8855_mii_read32(struct mii_bus *bus, u8 phy_id, u32 reg,
+			     u32 *val) __must_hold(&bus->mdio_lock)
+{
+	int lo, hi, ret;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
+			      AN8855_PBUS_MODE_ADDR_FIXED);
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_HIGH,
+			      upper_16_bits(reg));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_LOW,
+			      lower_16_bits(reg));
+	if (ret)
+		goto err;
+
+	hi = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_HIGH);
+	if (hi < 0) {
+		ret = hi;
+		goto err;
+	}
+
+	lo = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_LOW);
+	if (lo < 0) {
+		ret = lo;
+		goto err;
+	}
+
+	*val = ((u16)hi << 16) | ((u16)lo & 0xffff);
+
+	return 0;
+err:
+	dev_err_ratelimited(&bus->dev, "failed to read register\n");
+	return ret;
+}
+
+static int an8855_regmap_read(void *ctx, uint32_t reg, uint32_t *val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	u16 addr = priv->switch_addr;
+	int ret;
+
+	/* Workaround a HW BUG where using only PBUS for
+	 * accessing internal PHY register cause the port status
+	 * to not be correctly detected. It seems BMSR is required
+	 * to go through direct MDIO read or is never refreshed.
+	 *
+	 * A theory about this is that PHY sideband signal is
+	 * checked only with MDIO operation on BMSR and using
+	 * PBUS doesn't trigger the check.
+	 *
+	 * Using interrupt to detect Link Up might be possible
+	 * but it's considered an optional feature for the Switch
+	 * reference (hence there could be devices with the
+	 * interrupt line not connected)
+	 */
+	if (an8855_is_pbus_bmcr_reg(reg)) {
+		addr += FIELD_GET(AN8855_GPHY_PORT, reg);
+		*val = mdiobus_read(bus, addr, MII_BMSR);
+		return 0;
+	}
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret < 0)
+		goto exit;
+
+	ret = an8855_mii_read32(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int an8855_mii_write32(struct mii_bus *bus, u8 phy_id, u32 reg,
+			      u32 val) __must_hold(&bus->mdio_lock)
+{
+	int ret;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
+			      AN8855_PBUS_MODE_ADDR_FIXED);
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_HIGH,
+			      upper_16_bits(reg));
+	if (ret)
+		goto err;
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_LOW,
+			      lower_16_bits(reg));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_DATA_HIGH,
+			      upper_16_bits(val));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_DATA_LOW,
+			      lower_16_bits(val));
+	if (ret)
+		goto err;
+
+	return 0;
+err:
+	dev_err_ratelimited(&bus->dev,
+			    "failed to write an8855 register\n");
+	return ret;
+}
+
+static int an8855_regmap_write(void *ctx, uint32_t reg, uint32_t val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	u16 addr = priv->switch_addr;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret)
+		goto exit;
+
+	ret = an8855_mii_write32(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int an8855_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask,
+				     uint32_t write_val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	u16 addr = priv->switch_addr;
+	u32 val;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret)
+		goto exit;
+
+	ret = an8855_mii_read32(bus, addr, reg, &val);
+	if (ret < 0)
+		goto exit;
+
+	val &= ~mask;
+	val |= write_val;
+	ret = an8855_mii_write32(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static const struct regmap_range an8855_readable_ranges[] = {
+	regmap_reg_range(0x10000000, 0x10000fff), /* SCU */
+	regmap_reg_range(0x10001000, 0x10001fff), /* RBUS */
+	regmap_reg_range(0x10002000, 0x10002fff), /* MCU */
+	regmap_reg_range(0x10005000, 0x10005fff), /* SYS SCU */
+	regmap_reg_range(0x10007000, 0x10007fff), /* I2C Slave */
+	regmap_reg_range(0x10008000, 0x10008fff), /* I2C Master */
+	regmap_reg_range(0x10009000, 0x10009fff), /* PDMA */
+	regmap_reg_range(0x1000a100, 0x1000a2ff), /* General Purpose Timer */
+	regmap_reg_range(0x1000a200, 0x1000a2ff), /* GPU timer */
+	regmap_reg_range(0x1000a300, 0x1000a3ff), /* GPIO */
+	regmap_reg_range(0x1000a400, 0x1000a5ff), /* EFUSE */
+	regmap_reg_range(0x1000c000, 0x1000cfff), /* GDMP CSR */
+	regmap_reg_range(0x10010000, 0x1001ffff), /* GDMP SRAM */
+	regmap_reg_range(0x10200000, 0x10203fff), /* Switch - ARL Global */
+	regmap_reg_range(0x10204000, 0x10207fff), /* Switch - BMU */
+	regmap_reg_range(0x10208000, 0x1020bfff), /* Switch - ARL Port */
+	regmap_reg_range(0x1020c000, 0x1020cfff), /* Switch - SCH */
+	regmap_reg_range(0x10210000, 0x10213fff), /* Switch - MAC */
+	regmap_reg_range(0x10214000, 0x10217fff), /* Switch - MIB */
+	regmap_reg_range(0x10218000, 0x1021bfff), /* Switch - Port Control */
+	regmap_reg_range(0x1021c000, 0x1021ffff), /* Switch - TOP */
+	regmap_reg_range(0x10220000, 0x1022ffff), /* SerDes */
+	regmap_reg_range(0x10286000, 0x10286fff), /* RG Batcher */
+	regmap_reg_range(0x1028c000, 0x1028ffff), /* ETHER_SYS */
+	regmap_reg_range(0x30000000, 0x37ffffff), /* I2C EEPROM */
+	regmap_reg_range(0x38000000, 0x3fffffff), /* BOOT_ROM */
+	regmap_reg_range(0xa0000000, 0xbfffffff), /* GPHY */
+};
+
+static const struct regmap_access_table an8855_readable_table = {
+	.yes_ranges = an8855_readable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(an8855_readable_ranges),
+};
+
+static const struct regmap_config an8855_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0xbfffffff,
+	.reg_read = an8855_regmap_read,
+	.reg_write = an8855_regmap_write,
+	.reg_update_bits = an8855_regmap_update_bits,
+	.disable_locking = true,
+	.rd_table = &an8855_readable_table,
+};
+
+static int an8855_read_switch_id(struct device *dev, struct regmap *regmap)
+{
+	u32 id;
+	int ret;
+
+	ret = regmap_read(regmap, AN8855_CREV, &id);
+	if (ret)
+		return ret;
+
+	if (id != AN8855_ID) {
+		dev_err(dev, "Detected Switch ID %x but %x was expected\n",
+			id, AN8855_ID);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int an8855_core_probe(struct mdio_device *mdiodev)
+{
+	struct device *dev = &mdiodev->dev;
+	struct an8855_core_priv *priv;
+	struct gpio_desc *reset_gpio;
+	struct regmap *regmap;
+	u32 val;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->bus = mdiodev->bus;
+	priv->switch_addr = mdiodev->addr;
+	/* No DMA for mdiobus, mute warning for DMA mask not set */
+	dev->dma_mask = &dev->coherent_dma_mask;
+
+	regmap = devm_regmap_init(dev, NULL, priv, &an8855_regmap_config);
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap),
+				     "regmap initialization failed\n");
+
+	reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(reset_gpio))
+		return PTR_ERR(reset_gpio);
+
+	if (reset_gpio) {
+		usleep_range(100000, 150000);
+		gpiod_set_value_cansleep(reset_gpio, 0);
+		usleep_range(100000, 150000);
+		gpiod_set_value_cansleep(reset_gpio, 1);
+
+		/* Poll HWTRAP reg to wait for Switch to fully Init */
+		ret = regmap_read_poll_timeout(regmap, AN8855_HWTRAP, val,
+					       val, 20, 200000);
+		if (ret)
+			return ret;
+	}
+
+	ret = an8855_read_switch_id(dev, regmap);
+	if (ret)
+		return ret;
+
+	/* Release global PHY power down */
+	ret = regmap_write(regmap, AN8855_RG_GPHY_AFE_PWD, 0x0);
+	if (ret)
+		return ret;
+
+	return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, an8855_core_childs,
+				    ARRAY_SIZE(an8855_core_childs), NULL, 0,
+				    NULL);
+}
+
+static const struct of_device_id an8855_core_of_match[] = {
+	{ .compatible = "airoha,an8855" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_core_of_match);
+
+static struct mdio_driver an8855_core_driver = {
+	.probe = an8855_core_probe,
+	.mdiodrv.driver = {
+		.name = "an8855",
+		.of_match_table = an8855_core_of_match,
+	},
+};
+mdio_module_driver(an8855_core_driver);
+
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for Airoha AN8855 MFD");
+MODULE_LICENSE("GPL");
-- 
2.48.1

[net-next PATCH v15 10/12] net: phy: Add Airoha AN8855 Internal Switch Gigabit PHY

[Christian Marangi]

Add support for Airoha AN8855 Internal Switch Gigabit PHY.

This is a simple PHY driver to configure and calibrate the PHY for the
AN8855 Switch with the use of NVMEM cells.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/phy/Kconfig      |   5 +
 drivers/net/phy/Makefile     |   1 +
 drivers/net/phy/air_an8855.c | 261 +++++++++++++++++++++++++++++++++++
 3 files changed, 267 insertions(+)
 create mode 100644 drivers/net/phy/air_an8855.c

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 28acc6392cfc..d25f36c82c48 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -91,6 +91,11 @@ config AS21XXX_PHY
 	  AS21210PB1 that all register with the PHY ID 0x7500 0x7500
 	  before the firmware is loaded.
 
+config AIR_AN8855_PHY
+	tristate "Airoha AN8855 Internal Gigabit PHY"
+	help
+	  Currently supports the internal Airoha AN8855 Switch PHY.
+
 config AIR_EN8811H_PHY
 	tristate "Airoha EN8811H 2.5 Gigabit PHY"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index b4795aaf9c1c..734adf4a3855 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -29,6 +29,7 @@ obj-y				+= $(sfp-obj-y) $(sfp-obj-m)
 
 obj-$(CONFIG_ADIN_PHY)		+= adin.o
 obj-$(CONFIG_ADIN1100_PHY)	+= adin1100.o
+obj-$(CONFIG_AIR_AN8855_PHY)   += air_an8855.o
 obj-$(CONFIG_AIR_EN8811H_PHY)   += air_en8811h.o
 obj-$(CONFIG_AMD_PHY)		+= amd.o
 obj-$(CONFIG_AMCC_QT2025_PHY)	+= qt2025.o
diff --git a/drivers/net/phy/air_an8855.c b/drivers/net/phy/air_an8855.c
new file mode 100644
index 000000000000..a740dbaacf9a
--- /dev/null
+++ b/drivers/net/phy/air_an8855.c
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Christian Marangi <ansuelsmth@gmail.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+
+#define AN8855_PHY_SELECT_PAGE			0x1f
+#define   AN8855_PHY_PAGE			GENMASK(2, 0)
+#define   AN8855_PHY_PAGE_STANDARD		FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
+#define   AN8855_PHY_PAGE_EXTENDED_1		FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
+
+/* MII Registers Page 1 */
+#define AN8855_PHY_EXT_REG_14			0x14
+#define   AN8855_PHY_EN_DOWN_SHIFT		BIT(4)
+
+/* R50 Calibration regs in MDIO_MMD_VEND1 */
+#define AN8855_PHY_R500HM_RSEL_TX_AB		0x174
+#define AN8855_PHY_R50OHM_RSEL_TX_A_EN		BIT(15)
+#define AN8855_PHY_R50OHM_RSEL_TX_A		GENMASK(14, 8)
+#define AN8855_PHY_R50OHM_RSEL_TX_B_EN		BIT(7)
+#define AN8855_PHY_R50OHM_RSEL_TX_B		GENMASK(6, 0)
+#define AN8855_PHY_R500HM_RSEL_TX_CD		0x175
+#define AN8855_PHY_R50OHM_RSEL_TX_C_EN		BIT(15)
+#define AN8855_PHY_R50OHM_RSEL_TX_C		GENMASK(14, 8)
+#define AN8855_PHY_R50OHM_RSEL_TX_D_EN		BIT(7)
+#define AN8855_PHY_R50OHM_RSEL_TX_D		GENMASK(6, 0)
+
+#define AN8855_SWITCH_EFUSE_R50O		GENMASK(30, 24)
+
+/* PHY TX PAIR DELAY SELECT Register */
+#define AN8855_PHY_TX_PAIR_DLY_SEL_GBE		0x013
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_A_GBE GENMASK(14, 12)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_B_GBE GENMASK(10, 8)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_C_GBE GENMASK(6, 4)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_D_GBE GENMASK(2, 0)
+/* PHY ADC Register */
+#define AN8855_PHY_RXADC_CTRL			0x0d8
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_A	BIT(12)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_B	BIT(8)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_C	BIT(4)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_D	BIT(0)
+#define AN8855_PHY_RXADC_REV_0			0x0d9
+#define   AN8855_PHY_RG_AD_RESERVE0_A		GENMASK(15, 8)
+#define   AN8855_PHY_RG_AD_RESERVE0_B		GENMASK(7, 0)
+#define AN8855_PHY_RXADC_REV_1			0x0da
+#define   AN8855_PHY_RG_AD_RESERVE0_C		GENMASK(15, 8)
+#define   AN8855_PHY_RG_AD_RESERVE0_D		GENMASK(7, 0)
+
+#define AN8855_PHY_ID				0xc0ff0410
+
+struct air_an8855_priv {
+	bool needs_calibration;
+};
+
+static const u8 dsa_r50ohm_table[] = {
+	127, 127, 127, 127, 127, 127, 127, 127, 127, 127,
+	127, 127, 127, 127, 127, 127, 127, 126, 122, 117,
+	112, 109, 104, 101,  97,  94,  90,  88,  84,  80,
+	78,  74,  72,  68,  66,  64,  61,  58,  56,  53,
+	51,  48,  47,  44,  42,  40,  38,  36,  34,  32,
+	31,  28,  27,  24,  24,  22,  20,  18,  16,  16,
+	14,  12,  11,   9
+};
+
+static int en8855_get_r50ohm_val(struct device *dev, const char *calib_name,
+				 u8 *dest)
+{
+	u32 shift_sel, val;
+	int ret;
+	int i;
+
+	ret = nvmem_cell_read_u32(dev, calib_name, &val);
+	if (ret)
+		return ret;
+
+	shift_sel = FIELD_GET(AN8855_SWITCH_EFUSE_R50O, val);
+	for (i = 0; i < ARRAY_SIZE(dsa_r50ohm_table); i++)
+		if (dsa_r50ohm_table[i] == shift_sel)
+			break;
+
+	if (i < 8 || i >= ARRAY_SIZE(dsa_r50ohm_table))
+		*dest = dsa_r50ohm_table[25];
+	else
+		*dest = dsa_r50ohm_table[i - 8];
+
+	return 0;
+}
+
+static int an8855_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct air_an8855_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->needs_calibration = of_property_present(dev->of_node,
+						      "nvmem-cells");
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static int an8855_get_downshift(struct phy_device *phydev, u8 *data)
+{
+	int val;
+
+	val = phy_read_paged(phydev, AN8855_PHY_PAGE_EXTENDED_1, AN8855_PHY_EXT_REG_14);
+	if (val < 0)
+		return val;
+
+	*data = val & AN8855_PHY_EN_DOWN_SHIFT ? DOWNSHIFT_DEV_DEFAULT_COUNT :
+						 DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int an8855_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	u16 ds = cnt != DOWNSHIFT_DEV_DISABLE ? AN8855_PHY_EN_DOWN_SHIFT : 0;
+
+	return phy_modify_paged(phydev, AN8855_PHY_PAGE_EXTENDED_1,
+				AN8855_PHY_EXT_REG_14, AN8855_PHY_EN_DOWN_SHIFT,
+				ds);
+}
+
+static int an8855_config_init(struct phy_device *phydev)
+{
+	struct air_an8855_priv *priv = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+
+	/* Enable HW auto downshift */
+	ret = an8855_set_downshift(phydev, DOWNSHIFT_DEV_DEFAULT_COUNT);
+	if (ret)
+		return ret;
+
+	if (priv->needs_calibration) {
+		u8 calibration_data[4];
+
+		ret = en8855_get_r50ohm_val(dev, "tx_a", &calibration_data[0]);
+		if (ret)
+			return ret;
+
+		ret = en8855_get_r50ohm_val(dev, "tx_b", &calibration_data[1]);
+		if (ret)
+			return ret;
+
+		ret = en8855_get_r50ohm_val(dev, "tx_c", &calibration_data[2]);
+		if (ret)
+			return ret;
+
+		ret = en8855_get_r50ohm_val(dev, "tx_d", &calibration_data[3]);
+		if (ret)
+			return ret;
+
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_R500HM_RSEL_TX_AB,
+				     AN8855_PHY_R50OHM_RSEL_TX_A | AN8855_PHY_R50OHM_RSEL_TX_B,
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_A, calibration_data[0]) |
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_B, calibration_data[1]));
+		if (ret)
+			return ret;
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_R500HM_RSEL_TX_CD,
+				     AN8855_PHY_R50OHM_RSEL_TX_C | AN8855_PHY_R50OHM_RSEL_TX_D,
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_C, calibration_data[2]) |
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_D, calibration_data[3]));
+		if (ret)
+			return ret;
+	}
+
+	/* Apply values to reduce signal noise */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_TX_PAIR_DLY_SEL_GBE,
+			    FIELD_PREP(AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_A_GBE, 0x4) |
+			    FIELD_PREP(AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_C_GBE, 0x4));
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_CTRL,
+			    AN8855_PHY_RG_AD_SAMNPLE_PHSEL_A |
+			    AN8855_PHY_RG_AD_SAMNPLE_PHSEL_C);
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_REV_0,
+			    FIELD_PREP(AN8855_PHY_RG_AD_RESERVE0_A, 0x1));
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_REV_1,
+			    FIELD_PREP(AN8855_PHY_RG_AD_RESERVE0_C, 0x1));
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int an8855_get_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return an8855_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int an8855_set_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return an8855_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int an8855_read_page(struct phy_device *phydev)
+{
+	return __phy_read(phydev, AN8855_PHY_SELECT_PAGE);
+}
+
+static int an8855_write_page(struct phy_device *phydev, int page)
+{
+	return __phy_write(phydev, AN8855_PHY_SELECT_PAGE, page);
+}
+
+static struct phy_driver an8855_driver[] = {
+{
+	PHY_ID_MATCH_EXACT(AN8855_PHY_ID),
+	.name			= "Airoha AN8855 internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.flags			= PHY_IS_INTERNAL,
+	.probe			= an8855_probe,
+	.config_init		= an8855_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_tunable		= an8855_get_tunable,
+	.set_tunable		= an8855_set_tunable,
+	.suspend		= genphy_suspend,
+	.resume			= genphy_resume,
+	.read_page		= an8855_read_page,
+	.write_page		= an8855_write_page,
+}, };
+
+module_phy_driver(an8855_driver);
+
+static struct mdio_device_id __maybe_unused an8855_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(AN8855_PHY_ID) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, an8855_tbl);
+
+MODULE_DESCRIPTION("Airoha AN8855 PHY driver");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
-- 
2.48.1

[net-next PATCH v15 11/12] MAINTAINERS: add myself as maintainer for AN8855

[Christian Marangi]

Add myself as maintainer for AN8855 DSA driver and all the related
subdriver (mfd, mdio, phy, nvmem)

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 MAINTAINERS | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index bb9df569a3ff..2d1785478855 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -737,6 +737,25 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/net/airoha,en7581-eth.yaml
 F:	drivers/net/ethernet/airoha/
 
+AIROHA AN8855 DSA DRIVER
+M:	Christian Marangi <ansuelsmth@gmail.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
+F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
+F:	Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
+F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
+F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
+F:	drivers/mfd/airoha-an8855.c
+F:	drivers/net/dsa/an8855.c
+F:	drivers/net/dsa/an8855.h
+F:	drivers/net/mdio/mdio-an8855.c
+F:	drivers/net/phy/air_an8855.c
+F:	drivers/nvmem/an8855-efuse.c
+F:	include/linux/dsa/an8855.h
+
 AIROHA PCIE PHY DRIVER
 M:	Lorenzo Bianconi <lorenzo@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.48.1

[net-next PATCH v15 12/12] net: dsa: tag_mtk: add comments about Airoha usage of this TAG

[Christian Marangi]

Add comments about difference between Airoha AN8855 and Mediatek tag
bitmap.

Airoha AN88555 doesn't support controlling SA learning and Leaky VLAN
from tag. Although these bits are not used (and even not defined for
Leaky VLAN), it's worth to add comments for these difference to prevent
any kind of regression in the future if ever these bits will be used.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 net/dsa/tag_mtk.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/net/dsa/tag_mtk.c b/net/dsa/tag_mtk.c
index b670e3c53e91..ac3f956abe39 100644
--- a/net/dsa/tag_mtk.c
+++ b/net/dsa/tag_mtk.c
@@ -18,6 +18,9 @@
 #define MTK_HDR_XMIT_TAGGED_TPID_88A8	2
 #define MTK_HDR_RECV_SOURCE_PORT_MASK	GENMASK(2, 0)
 #define MTK_HDR_XMIT_DP_BIT_MASK	GENMASK(5, 0)
+/* AN8855 doesn't support SA_DIS and Leaky VLAN
+ * control in tag as these bits doesn't exist.
+ */
 #define MTK_HDR_XMIT_SA_DIS		BIT(6)
 
 static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb,
-- 
2.48.1

Re: [net-next PATCH v15 02/12] dt-bindings: net: Document support for Airoha AN8855 Switch PBUS MDIO

[Rob Herring (Arm)]

On Thu, 26 Jun 2025 23:23:01 +0200, Christian Marangi wrote:
> Document support for Airoha AN8855 PBUS MDIO. Airoha AN8855 Switch
> expose a way to access internal PHYs via Switch register.
> This is named internally PBUS and does the function of an MDIO bus
> for the internal PHYs.
> 
> It does support a maximum of 5 PHYs (matching the number of port
> the Switch support)
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/net/airoha,an8855-mdio.yaml      | 57 +++++++++++++++++++
>  1 file changed, 57 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [net-next PATCH v15 03/12] dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch

[Rob Herring]

On Thu, Jun 26, 2025 at 11:23:02PM +0200, Christian Marangi wrote:
> Document support for Airoha AN8855 5-port Gigabit Switch.
> 
> It does expose the 5 Internal PHYs on the MDIO bus and each port
> can access the Switch register space by configurting the PHY page.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../net/dsa/airoha,an8855-switch.yaml         | 86 +++++++++++++++++++
>  1 file changed, 86 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> new file mode 100644
> index 000000000000..fbb9219fadae
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> @@ -0,0 +1,86 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/dsa/airoha,an8855-switch.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Airoha AN8855 Gigabit Switch
> +
> +maintainers:
> +  - Christian Marangi <ansuelsmth@gmail.com>
> +
> +description: >
> +  Airoha AN8855 is a 5-port Gigabit Switch.
> +
> +  It does expose the 5 Internal PHYs on the MDIO bus and each port
> +  can access the Switch register space by configurting the PHY page.
> +
> +$ref: dsa.yaml#/$defs/ethernet-ports
> +
> +properties:
> +  compatible:
> +    const: airoha,an8855-switch
> +
> +required:
> +  - compatible
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    ethernet-switch {
> +        compatible = "airoha,an8855-switch";
> +
> +        ports {

ethernet-ports is preferred.

> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {

And ethernet-port@0


Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [net-next PATCH v15 05/12] dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC

[Rob Herring]

On Thu, Jun 26, 2025 at 11:23:04PM +0200, Christian Marangi wrote:
> Document support for Airoha AN8855 Switch SoC. This SoC expose various
> peripherals like an Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> 
> It does also support i2c and timers but those are not currently
> supported/used.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/mfd/airoha,an8855.yaml           | 175 ++++++++++++++++++
>  1 file changed, 175 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> 
> diff --git a/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> new file mode 100644
> index 000000000000..a683db4f41d1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> @@ -0,0 +1,175 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/airoha,an8855.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Airoha AN8855 Switch SoC
> +
> +maintainers:
> +  - Christian Marangi <ansuelsmth@gmail.com>
> +
> +description: >
> +  Airoha AN8855 Switch is a SoC that expose various peripherals like an
> +  Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> +
> +  It does also support i2c and timers but those are not currently
> +  supported/used.
> +
> +properties:
> +  compatible:
> +    const: airoha,an8855
> +
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios: true
> +
> +  efuse:
> +    type: object
> +    $ref: /schemas/nvmem/airoha,an8855-efuse.yaml
> +    description: EFUSE exposed by the Airoha AN8855 SoC
> +
> +  ethernet-switch:
> +    type: object
> +    $ref: /schemas/net/dsa/airoha,an8855-switch.yaml
> +    description: Switch exposed by the Airoha AN8855 SoC
> +
> +  mdio:
> +    type: object
> +    $ref: /schemas/net/airoha,an8855-mdio.yaml
> +    description: MDIO exposed by the Airoha AN8855 SoC
> +
> +required:
> +  - compatible
> +  - reg
> +  - mdio
> +  - ethernet-switch
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    mdio {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        soc@1 {
> +            compatible = "airoha,an8855";
> +            reg = <1>;
> +
> +            reset-gpios = <&pio 39 0>;
> +
> +            efuse {
> +                compatible = "airoha,an8855-efuse";
> +
> +                #nvmem-cell-cells = <0>;
> +
> +                nvmem-layout {
> +                    compatible = "fixed-layout";
> +                    #address-cells = <1>;
> +                    #size-cells = <1>;
> +
> +                    shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
> +                       reg = <0xc 0x4>;
> +                    };
> +
> +                    shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
> +                        reg = <0x10 0x4>;
> +                    };
> +
> +                    shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
> +                        reg = <0x14 0x4>;
> +                    };
> +
> +                    shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
> +                       reg = <0x18 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
> +                        reg = <0x1c 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
> +                        reg = <0x20 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
> +                       reg = <0x24 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
> +                        reg = <0x28 0x4>;
> +                    };
> +                };
> +            };
> +
> +            ethernet-switch {
> +                compatible = "airoha,an8855-switch";
> +
> +                ports {

Same comment here.

Why do we need 2 examples of the same thing? Isn't this 1 complete 
example here enough?

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Rob

Re: [net-next PATCH v15 05/12] dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC

[Christian Marangi]

On Fri, Jun 27, 2025 at 04:48:21PM -0500, Rob Herring wrote:
> On Thu, Jun 26, 2025 at 11:23:04PM +0200, Christian Marangi wrote:
> > Document support for Airoha AN8855 Switch SoC. This SoC expose various
> > peripherals like an Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> > 
> > It does also support i2c and timers but those are not currently
> > supported/used.
> > 
> > Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> > ---
> >  .../bindings/mfd/airoha,an8855.yaml           | 175 ++++++++++++++++++
> >  1 file changed, 175 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> > new file mode 100644
> > index 000000000000..a683db4f41d1
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> > @@ -0,0 +1,175 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/mfd/airoha,an8855.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Airoha AN8855 Switch SoC
> > +
> > +maintainers:
> > +  - Christian Marangi <ansuelsmth@gmail.com>
> > +
> > +description: >
> > +  Airoha AN8855 Switch is a SoC that expose various peripherals like an
> > +  Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> > +
> > +  It does also support i2c and timers but those are not currently
> > +  supported/used.
> > +
> > +properties:
> > +  compatible:
> > +    const: airoha,an8855
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  reset-gpios: true
> > +
> > +  efuse:
> > +    type: object
> > +    $ref: /schemas/nvmem/airoha,an8855-efuse.yaml
> > +    description: EFUSE exposed by the Airoha AN8855 SoC
> > +
> > +  ethernet-switch:
> > +    type: object
> > +    $ref: /schemas/net/dsa/airoha,an8855-switch.yaml
> > +    description: Switch exposed by the Airoha AN8855 SoC
> > +
> > +  mdio:
> > +    type: object
> > +    $ref: /schemas/net/airoha,an8855-mdio.yaml
> > +    description: MDIO exposed by the Airoha AN8855 SoC
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - mdio
> > +  - ethernet-switch
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/gpio/gpio.h>
> > +
> > +    mdio {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        soc@1 {
> > +            compatible = "airoha,an8855";
> > +            reg = <1>;
> > +
> > +            reset-gpios = <&pio 39 0>;
> > +
> > +            efuse {
> > +                compatible = "airoha,an8855-efuse";
> > +
> > +                #nvmem-cell-cells = <0>;
> > +
> > +                nvmem-layout {
> > +                    compatible = "fixed-layout";
> > +                    #address-cells = <1>;
> > +                    #size-cells = <1>;
> > +
> > +                    shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
> > +                       reg = <0xc 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
> > +                        reg = <0x10 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
> > +                        reg = <0x14 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
> > +                       reg = <0x18 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
> > +                        reg = <0x1c 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
> > +                        reg = <0x20 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
> > +                       reg = <0x24 0x4>;
> > +                    };
> > +
> > +                    shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
> > +                        reg = <0x28 0x4>;
> > +                    };
> > +                };
> > +            };
> > +
> > +            ethernet-switch {
> > +                compatible = "airoha,an8855-switch";
> > +
> > +                ports {
> 
> Same comment here.
> 
> Why do we need 2 examples of the same thing? Isn't this 1 complete 
> example here enough?
>

Do you prefer if I drop example from every other schema and keep only
this?

And with this change is it ok to keep the review tag?

-- 
	Ansuel

Re: [net-next PATCH v15 08/12] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver

[Thomas Weißschuh]

On 2025-06-26 23:23:07+0200, Christian Marangi wrote:
> Add Airoha AN8855 5-Port Gigabit DSA switch. Switch can support
> 10M, 100M, 1Gb, 2.5G and 5G Ethernet Speed but 5G is currently error out
> as it's not currently supported as requires additional configuration for
> the PCS.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  drivers/net/dsa/Kconfig  |    9 +
>  drivers/net/dsa/Makefile |    1 +
>  drivers/net/dsa/an8855.c | 2386 ++++++++++++++++++++++++++++++++++++++
>  drivers/net/dsa/an8855.h |  773 ++++++++++++
>  4 files changed, 3169 insertions(+)
>  create mode 100644 drivers/net/dsa/an8855.c
>  create mode 100644 drivers/net/dsa/an8855.h

<snip>

> +static int an8855_switch_probe(struct platform_device *pdev)
> +{
> +	struct an8855_priv *priv;
> +
> +	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	/* Get regmap from MFD */
> +	priv->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> +	if (!priv->regmap)
> +		return -ENOENT;
> +
> +	priv->ds = devm_kzalloc(&pdev->dev, sizeof(*priv->ds), GFP_KERNEL);
> +	if (!priv->ds)
> +		return -ENOMEM;
> +
> +	priv->ds->dev = &pdev->dev;
> +	priv->ds->num_ports = AN8855_NUM_PORTS;
> +	priv->ds->priv = priv;
> +	priv->ds->ops = &an8855_switch_ops;
> +	devm_mutex_init(&pdev->dev, &priv->reg_mutex);

Check the return value of devm_mutex_init().
This will become a compile error soon.

> +	priv->ds->phylink_mac_ops = &an8855_phylink_mac_ops;
> +
> +	priv->pcs.ops = &an8855_pcs_ops;
> +	priv->pcs.poll = true;
> +
> +	dev_set_drvdata(&pdev->dev, priv);
> +
> +	return dsa_register_switch(priv->ds);
> +}

<snip>

Re: [net-next PATCH v15 09/12] mfd: an8855: Add support for Airoha AN8855 Switch MFD

[Lee Jones]

> Add support for Airoha AN8855 Switch MFD that provide support for a DSA

Drop the MFD part from here and the subject line.

> switch and a NVMEM provider. Also provide support for the PBUS MDIO
> to access the internal PHYs address from the switch registers to permit
> the usage of a single regmap to handle both switch and PHYs.
> 
> An interesting HW bug wes discovered with the implementation of the MDIO
> PBUS where the PHY status is not correctly detected if the PBUS is used
> to read the PHY BMSR. For the only BMSR register, it's required to read
> the address directly from the MDIO bus.
> 
> A check and a workaround is implemented to address this in the
> regmap_read function.

Couple of final points.

Some of them are repeated from previous reviews.

> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  drivers/mfd/Kconfig         |  12 ++
>  drivers/mfd/Makefile        |   1 +
>  drivers/mfd/airoha-an8855.c | 393 ++++++++++++++++++++++++++++++++++++
>  3 files changed, 406 insertions(+)
>  create mode 100644 drivers/mfd/airoha-an8855.c
> 
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 6fb3768e3d71..f2bfd6c9fc5f 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -53,6 +53,18 @@ config MFD_ALTERA_SYSMGR
>  	  using regmap_mmio accesses for ARM32 parts and SMC calls to
>  	  EL3 for ARM64 parts.
>  
> +config MFD_AIROHA_AN8855
> +	tristate "Airoha AN8855 Switch Core"
> +	select MFD_CORE
> +	select MDIO_DEVICE
> +	depends on NETDEVICES && OF
> +	help
> +	  Support for the Airoha AN8855 Switch Core. This is an SoC
> +	  that provides various peripherals, to count, i2c, an Ethrnet
> +	  Switch, a CPU timer, GPIO, eFUSE.
> +
> +	  Currently it provides a DSA switch and a NVMEM provider.
> +
>  config MFD_ACT8945A
>  	tristate "Active-semi ACT8945A"
>  	select MFD_CORE
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 79495f9f3457..f541b513f41e 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -8,6 +8,7 @@ obj-$(CONFIG_MFD_88PM860X)	+= 88pm860x.o
>  obj-$(CONFIG_MFD_88PM800)	+= 88pm800.o 88pm80x.o
>  obj-$(CONFIG_MFD_88PM805)	+= 88pm805.o 88pm80x.o
>  obj-$(CONFIG_MFD_88PM886_PMIC)	+= 88pm886.o
> +obj-$(CONFIG_MFD_AIROHA_AN8855)	+= airoha-an8855.o
>  obj-$(CONFIG_MFD_ACT8945A)	+= act8945a.o
>  obj-$(CONFIG_MFD_SM501)		+= sm501.o
>  obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835-pm.o
> diff --git a/drivers/mfd/airoha-an8855.c b/drivers/mfd/airoha-an8855.c
> new file mode 100644
> index 000000000000..bb03a2436f25
> --- /dev/null
> +++ b/drivers/mfd/airoha-an8855.c
> @@ -0,0 +1,393 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Core driver for Airoha AN8855 Switch

No Copyright?

> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/dsa/an8855.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mdio.h>
> +#include <linux/mdio/mdio-regmap.h>
> +#include <linux/module.h>
> +#include <linux/phy.h>
> +#include <linux/regmap.h>
> +
> +/* Register for HW trap status */
> +#define AN8855_HWTRAP			0x1000009c
> +
> +#define AN8855_CREV			0x10005000

Please change the name of this or comment it.

I still have no idea what it is.

> +#define   AN8855_ID			0x8855

Device ID, Chip ID, Platform ID, Driver's ID?

> +#define AN8855_RG_GPHY_AFE_PWD		0x1028c840

No clue.  Comment please.

> +/* MII Registers */
> +#define AN8855_PHY_SELECT_PAGE		0x1f
> +#define   AN8855_PHY_PAGE		GENMASK(2, 0)
> +#define   AN8855_PHY_PAGE_STANDARD	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
> +#define   AN8855_PHY_PAGE_EXTENDED_1	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
> +#define   AN8855_PHY_PAGE_EXTENDED_4	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x4)
> +
> +/* MII Registers Page 4 */
> +#define AN8855_PBUS_MODE		0x10
> +#define   AN8855_PBUS_MODE_ADDR_FIXED	0x0
> +#define   AN8855_PBUS_MODE_ADDR_INCR	BIT(15)
> +#define AN8855_PBUS_WR_ADDR_HIGH	0x11
> +#define AN8855_PBUS_WR_ADDR_LOW		0x12
> +#define AN8855_PBUS_WR_DATA_HIGH	0x13
> +#define AN8855_PBUS_WR_DATA_LOW		0x14
> +#define AN8855_PBUS_RD_ADDR_HIGH	0x15
> +#define AN8855_PBUS_RD_ADDR_LOW		0x16
> +#define AN8855_PBUS_RD_DATA_HIGH	0x17
> +#define AN8855_PBUS_RD_DATA_LOW		0x18
> +
> +struct an8855_core_priv {
> +	struct mii_bus *bus;
> +

Do we need this separation between only 2 attributes?

> +	unsigned int switch_addr;
> +};
> +
> +static const struct mfd_cell an8855_core_childs[] = {

an8855_{devs,cells}

> +	{
> +		.name = "an8855-efuse",
> +		.of_compatible = "airoha,an8855-efuse",

MFD_CELL_OF()

> +	}, {
> +		.name = "an8855-switch",
> +		.of_compatible = "airoha,an8855-switch",
> +	}, {
> +		.name = "an8855-mdio",
> +		.of_compatible = "airoha,an8855-mdio",
> +	}
> +};
> +
> +static bool an8855_is_pbus_bmcr_reg(u32 reg)
> +{
> +	if ((reg & ~(AN8855_GPHY_PORT | AN8855_ADDR)) != AN8855_GPHY_ACCESS)
> +		return false;
> +
> +	if ((reg & AN8855_ADDR) != FIELD_PREP_CONST(AN8855_CL22_ADDR,
> +						    MII_BMSR))
> +		return false;
> +
> +	return true;
> +}
> +
> +/* PHY page is Global for every Switch PHY.
> + * Configure it to 4 (as Switch PAGE) and keep it that way.
> + * Page selection doesn't affect the first PHY address from 0x0 to
> + * 0xf and we use PBUS to access the PHY address.
> + */

Proper multi-line comments please.

> +static int an8855_mii_set_page(struct an8855_core_priv *priv, u8 addr,
> +			       u8 page) __must_hold(&priv->bus->mdio_lock)
> +{
> +	struct mii_bus *bus = priv->bus;
> +	int ret;
> +
> +	ret = __mdiobus_write(bus, addr, AN8855_PHY_SELECT_PAGE, page);
> +	if (ret)
> +		dev_err_ratelimited(&bus->dev, "failed to set mii page\n");
> +
> +	return ret;
> +}
> +
> +static int an8855_mii_read32(struct mii_bus *bus, u8 phy_id, u32 reg,
> +			     u32 *val) __must_hold(&bus->mdio_lock)
> +{
> +	int lo, hi, ret;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
> +			      AN8855_PBUS_MODE_ADDR_FIXED);

You can use up to 100-chars, if you want to avoid all of this wraps.

> +	if (ret)
> +		goto err;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_HIGH,
> +			      upper_16_bits(reg));
> +	if (ret)
> +		goto err;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_LOW,
> +			      lower_16_bits(reg));
> +	if (ret)
> +		goto err;
> +
> +	hi = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_HIGH);
> +	if (hi < 0) {
> +		ret = hi;
> +		goto err;
> +	}
> +
> +	lo = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_LOW);
> +	if (lo < 0) {
> +		ret = lo;
> +		goto err;
> +	}
> +
> +	*val = ((u16)hi << 16) | ((u16)lo & 0xffff);
> +
> +	return 0;
> +err:
> +	dev_err_ratelimited(&bus->dev, "failed to read register\n");
> +	return ret;
> +}
> +
> +static int an8855_regmap_read(void *ctx, uint32_t reg, uint32_t *val)
> +{
> +	struct an8855_core_priv *priv = ctx;
> +	struct mii_bus *bus = priv->bus;
> +	u16 addr = priv->switch_addr;
> +	int ret;
> +
> +	/* Workaround a HW BUG where using only PBUS for
> +	 * accessing internal PHY register cause the port status
> +	 * to not be correctly detected. It seems BMSR is required
> +	 * to go through direct MDIO read or is never refreshed.
> +	 *
> +	 * A theory about this is that PHY sideband signal is
> +	 * checked only with MDIO operation on BMSR and using
> +	 * PBUS doesn't trigger the check.
> +	 *
> +	 * Using interrupt to detect Link Up might be possible
> +	 * but it's considered an optional feature for the Switch
> +	 * reference (hence there could be devices with the
> +	 * interrupt line not connected)
> +	 */

Re: comment formatting - as above and throughout.

> +	if (an8855_is_pbus_bmcr_reg(reg)) {
> +		addr += FIELD_GET(AN8855_GPHY_PORT, reg);
> +		*val = mdiobus_read(bus, addr, MII_BMSR);
> +		return 0;
> +	}
> +
> +	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> +	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
> +	if (ret < 0)
> +		goto exit;
> +
> +	ret = an8855_mii_read32(bus, addr, reg, val);
> +
> +exit:
> +	mutex_unlock(&bus->mdio_lock);
> +
> +	return ret < 0 ? ret : 0;
> +}
> +
> +static int an8855_mii_write32(struct mii_bus *bus, u8 phy_id, u32 reg,
> +			      u32 val) __must_hold(&bus->mdio_lock)
> +{
> +	int ret;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
> +			      AN8855_PBUS_MODE_ADDR_FIXED);
> +	if (ret)
> +		goto err;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_HIGH,
> +			      upper_16_bits(reg));
> +	if (ret)
> +		goto err;
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_LOW,
> +			      lower_16_bits(reg));
> +	if (ret)
> +		goto err;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_DATA_HIGH,
> +			      upper_16_bits(val));
> +	if (ret)
> +		goto err;
> +
> +	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_DATA_LOW,
> +			      lower_16_bits(val));
> +	if (ret)
> +		goto err;
> +
> +	return 0;
> +err:
> +	dev_err_ratelimited(&bus->dev,
> +			    "failed to write an8855 register\n");
> +	return ret;
> +}
> +
> +static int an8855_regmap_write(void *ctx, uint32_t reg, uint32_t val)
> +{
> +	struct an8855_core_priv *priv = ctx;
> +	struct mii_bus *bus = priv->bus;
> +	u16 addr = priv->switch_addr;
> +	int ret;
> +
> +	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> +	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
> +	if (ret)
> +		goto exit;
> +
> +	ret = an8855_mii_write32(bus, addr, reg, val);
> +
> +exit:
> +	mutex_unlock(&bus->mdio_lock);
> +
> +	return ret < 0 ? ret : 0;
> +}
> +
> +static int an8855_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask,
> +				     uint32_t write_val)
> +{
> +	struct an8855_core_priv *priv = ctx;
> +	struct mii_bus *bus = priv->bus;
> +	u16 addr = priv->switch_addr;
> +	u32 val;
> +	int ret;
> +
> +	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> +	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
> +	if (ret)
> +		goto exit;
> +
> +	ret = an8855_mii_read32(bus, addr, reg, &val);
> +	if (ret < 0)
> +		goto exit;
> +
> +	val &= ~mask;
> +	val |= write_val;
> +	ret = an8855_mii_write32(bus, addr, reg, val);
> +
> +exit:
> +	mutex_unlock(&bus->mdio_lock);
> +
> +	return ret < 0 ? ret : 0;
> +}
> +
> +static const struct regmap_range an8855_readable_ranges[] = {
> +	regmap_reg_range(0x10000000, 0x10000fff), /* SCU */
> +	regmap_reg_range(0x10001000, 0x10001fff), /* RBUS */
> +	regmap_reg_range(0x10002000, 0x10002fff), /* MCU */
> +	regmap_reg_range(0x10005000, 0x10005fff), /* SYS SCU */
> +	regmap_reg_range(0x10007000, 0x10007fff), /* I2C Slave */
> +	regmap_reg_range(0x10008000, 0x10008fff), /* I2C Master */
> +	regmap_reg_range(0x10009000, 0x10009fff), /* PDMA */
> +	regmap_reg_range(0x1000a100, 0x1000a2ff), /* General Purpose Timer */
> +	regmap_reg_range(0x1000a200, 0x1000a2ff), /* GPU timer */
> +	regmap_reg_range(0x1000a300, 0x1000a3ff), /* GPIO */
> +	regmap_reg_range(0x1000a400, 0x1000a5ff), /* EFUSE */
> +	regmap_reg_range(0x1000c000, 0x1000cfff), /* GDMP CSR */
> +	regmap_reg_range(0x10010000, 0x1001ffff), /* GDMP SRAM */
> +	regmap_reg_range(0x10200000, 0x10203fff), /* Switch - ARL Global */
> +	regmap_reg_range(0x10204000, 0x10207fff), /* Switch - BMU */
> +	regmap_reg_range(0x10208000, 0x1020bfff), /* Switch - ARL Port */
> +	regmap_reg_range(0x1020c000, 0x1020cfff), /* Switch - SCH */
> +	regmap_reg_range(0x10210000, 0x10213fff), /* Switch - MAC */
> +	regmap_reg_range(0x10214000, 0x10217fff), /* Switch - MIB */
> +	regmap_reg_range(0x10218000, 0x1021bfff), /* Switch - Port Control */
> +	regmap_reg_range(0x1021c000, 0x1021ffff), /* Switch - TOP */
> +	regmap_reg_range(0x10220000, 0x1022ffff), /* SerDes */
> +	regmap_reg_range(0x10286000, 0x10286fff), /* RG Batcher */
> +	regmap_reg_range(0x1028c000, 0x1028ffff), /* ETHER_SYS */
> +	regmap_reg_range(0x30000000, 0x37ffffff), /* I2C EEPROM */
> +	regmap_reg_range(0x38000000, 0x3fffffff), /* BOOT_ROM */
> +	regmap_reg_range(0xa0000000, 0xbfffffff), /* GPHY */
> +};
> +
> +static const struct regmap_access_table an8855_readable_table = {
> +	.yes_ranges = an8855_readable_ranges,
> +	.n_yes_ranges = ARRAY_SIZE(an8855_readable_ranges),
> +};
> +
> +static const struct regmap_config an8855_regmap_config = {
> +	.reg_bits = 32,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +	.max_register = 0xbfffffff,
> +	.reg_read = an8855_regmap_read,
> +	.reg_write = an8855_regmap_write,
> +	.reg_update_bits = an8855_regmap_update_bits,
> +	.disable_locking = true,
> +	.rd_table = &an8855_readable_table,
> +};
> +
> +static int an8855_read_switch_id(struct device *dev, struct regmap *regmap)
> +{
> +	u32 id;
> +	int ret;
> +
> +	ret = regmap_read(regmap, AN8855_CREV, &id);
> +	if (ret)
> +		return ret;
> +
> +	if (id != AN8855_ID) {
> +		dev_err(dev, "Detected Switch ID %x but %x was expected\n",
> +			id, AN8855_ID);
> +		return -ENODEV;
> +	}
> +
> +	return 0;
> +}
> +
> +static int an8855_core_probe(struct mdio_device *mdiodev)
> +{
> +	struct device *dev = &mdiodev->dev;
> +	struct an8855_core_priv *priv;
> +	struct gpio_desc *reset_gpio;
> +	struct regmap *regmap;
> +	u32 val;
> +	int ret;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->bus = mdiodev->bus;
> +	priv->switch_addr = mdiodev->addr;
> +	/* No DMA for mdiobus, mute warning for DMA mask not set */
> +	dev->dma_mask = &dev->coherent_dma_mask;
> +
> +	regmap = devm_regmap_init(dev, NULL, priv, &an8855_regmap_config);
> +	if (IS_ERR(regmap))
> +		return dev_err_probe(dev, PTR_ERR(regmap),
> +				     "regmap initialization failed\n");
> +
> +	reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(reset_gpio))
> +		return PTR_ERR(reset_gpio);
> +
> +	if (reset_gpio) {
> +		usleep_range(100000, 150000);
> +		gpiod_set_value_cansleep(reset_gpio, 0);
> +		usleep_range(100000, 150000);
> +		gpiod_set_value_cansleep(reset_gpio, 1);
> +
> +		/* Poll HWTRAP reg to wait for Switch to fully Init */
> +		ret = regmap_read_poll_timeout(regmap, AN8855_HWTRAP, val,
> +					       val, 20, 200000);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	ret = an8855_read_switch_id(dev, regmap);
> +	if (ret)
> +		return ret;
> +
> +	/* Release global PHY power down */
> +	ret = regmap_write(regmap, AN8855_RG_GPHY_AFE_PWD, 0x0);
> +	if (ret)
> +		return ret;
> +
> +	return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, an8855_core_childs,
> +				    ARRAY_SIZE(an8855_core_childs), NULL, 0,
> +				    NULL);
> +}
> +
> +static const struct of_device_id an8855_core_of_match[] = {
> +	{ .compatible = "airoha,an8855" },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, an8855_core_of_match);
> +
> +static struct mdio_driver an8855_core_driver = {
> +	.probe = an8855_core_probe,
> +	.mdiodrv.driver = {
> +		.name = "an8855",
> +		.of_match_table = an8855_core_of_match,
> +	},
> +};
> +mdio_module_driver(an8855_core_driver);
> +
> +MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
> +MODULE_DESCRIPTION("Driver for Airoha AN8855 MFD");

Drop MFD.

> +MODULE_LICENSE("GPL");
> -- 
> 2.48.1
> 

-- 
Lee Jones [李琼斯]