[PATCH v4 0/6] arm64: qcom: allow up to 4 lanes for the Type-C DisplayPort Altmode

[PATCH v4 0/6] arm64: qcom: allow up to 4 lanes for the Type-C DisplayPort Altmode

[Konrad Dybcio]

Register a typec mux in order to change the PHY mode on the Type-C
mux events depending on the mode and the svid when in Altmode setup.

The DisplayPort phy should be left enabled if is still powered on
by the DRM DisplayPort controller, so bail out until the DisplayPort
PHY is not powered off.

The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
will be set in between of USB-Only, Combo and DisplayPort Only so
this will leave enough time to the DRM DisplayPort controller to
turn of the DisplayPort PHY.

The patchset also includes bindings changes and DT changes.

This has been successfully tested on an SM8550 board, but the
Thinkpad X13s deserved testing between non-PD USB, non-PD DisplayPort,
PD USB Hubs and PD Altmode Dongles to make sure the switch works
as expected.

The DisplayPort 4 lanes setup can be check with:
$ cat /sys/kernel/debug/dri/ae01000.display-controller/DP-1/dp_debug
	name = msm_dp
	drm_dp_link
		rate = 540000
		num_lanes = 4
...

This patchset depends on [1] to allow broadcasting the type-c mode
to the PHY, otherwise the PHY will keep the combo state while the
retimer would setup the 4 lanes in DP mode.

[1] https://lore.kernel.org/all/20240527-topic-sm8x50-upstream-retimer-broadcast-mode-v1-0-79ec91381aba@linaro.org/

Changes in v4:
- Default to USB3_ONLY if there's no DP SVID (Dmitry)
- Pick up tags, dropped T-bys due to the above change
- Add missing submitter's sign-off on some patches
- The odd 4-lane-DP + USB2 case remains unhandled for now, but it's
  not a huge deal, see:
  <c2f2ba36-1a25-450e-99b9-79aa4fd4913d@linaro.org>
- Link to v3: https://lore.kernel.org/r/20250527-topic-4ln_dp_respin-v3-0-f9a0763ec289@oss.qualcomm.com
Changes in v3:
- Take the series from Neil
- Rebase
- Rename many variables
- Test on X1E & X13s
- Apply a number of small cosmetic/codestyle changes
- Remove some unused variables
- Some smaller bugfixes
- Link to v2: https://lore.kernel.org/lkml/20240527-topic-sm8x50-upstream-phy-combo-typec-mux-v2-0-a03e68d7b8fc@linaro.org/
Changes in v2:
- Reference usb-switch.yaml in bindings patch
- Fix switch/case indenting
- Check svid for USB_TYPEC_DP_SID
- Fix X13s patch subject
- Update SM8650 patch to enable 4 lanes on HDK aswell
- Link to v1: https://lore.kernel.org/r/20240229-topic-sm8x50-upstream-phy-combo-typec-mux-v1-0-07e24a231840@linaro.org

Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
Konrad Dybcio (1):
      phy: qcom: qmp-combo: Rename 'mode' to 'phy_mode'

Neil Armstrong (5):
      dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch
      phy: qcom: qmp-combo: store DP phy power state
      phy: qcom: qmp-combo: introduce QMPPHY_MODE
      phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE
      arm64: dts: qcom: sc8280xp-lenovo-thinkpad-x13: Set up 4-lane DP

 .../phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml         |   7 +-
 .../dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts     |   6 +-
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c          | 179 +++++++++++++++++++--
 3 files changed, 170 insertions(+), 22 deletions(-)
---
base-commit: 442d93313caebc8ccd6d53f4572c50732a95bc48
change-id: 20250527-topic-4ln_dp_respin-c6924a8825ce

Best regards,
-- 
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

[PATCH v4 1/6] dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch

[Konrad Dybcio]

From: Neil Armstrong <neil.armstrong@linaro.org>

The QMP USB3/DP Combo PHY can work in 3 modes:
- DisplayPort Only
- USB3 Only
- USB3 + DisplayPort Combo mode

In order to switch between those modes, the PHY needs to receive
Type-C events, allow marking to the phy with the mode-switch
property in order to allow the PHY to Type-C events.

Reference usb-switch.yaml as a simpler way to allow the mode-switch
property instead of duplicating the property definition.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml     | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
index 38ce04c35d945d0d8d319191c241920810ee9005..c8bc512df08b5694c8599f475de78679a4438449 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
@@ -73,10 +73,8 @@ properties:
     description:
       See include/dt-bindings/phy/phy-qcom-qmp.h
 
-  orientation-switch:
-    description:
-      Flag the PHY as possible handler of USB Type-C orientation switching
-    type: boolean
+  mode-switch: true
+  orientation-switch: true
 
   ports:
     $ref: /schemas/graph.yaml#/properties/ports
@@ -106,6 +104,7 @@ required:
   - "#phy-cells"
 
 allOf:
+  - $ref: /schemas/usb/usb-switch.yaml#
   - if:
       properties:
         compatible:

-- 
2.50.1

[PATCH v4 2/6] phy: qcom: qmp-combo: Rename 'mode' to 'phy_mode'

[Konrad Dybcio]

From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

There are a numbers of ""modes"" involved: USB mode, Type-C mode (with
its altmodes), phy_mode and QMP_PHY mode (DP/combo/USB/off).

Rename the generic sounding 'mode' to 'phy_mode' to hopefully make
the code easier to follow.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index f07d097b129fb7b3fad003103b7468b16c1c4390..30749943f66280c3aa9e9673466f6f736d1adbc8 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -1846,7 +1846,7 @@ struct qmp_combo {
 	int init_count;
 
 	struct phy *usb_phy;
-	enum phy_mode mode;
+	enum phy_mode phy_mode;
 	unsigned int usb_init_count;
 
 	struct phy *dp_phy;
@@ -3282,7 +3282,7 @@ static int qmp_combo_usb_set_mode(struct phy *phy, enum phy_mode mode, int submo
 {
 	struct qmp_combo *qmp = phy_get_drvdata(phy);
 
-	qmp->mode = mode;
+	qmp->phy_mode = mode;
 
 	return 0;
 }
@@ -3311,8 +3311,8 @@ static void qmp_combo_enable_autonomous_mode(struct qmp_combo *qmp)
 	void __iomem *pcs_misc = qmp->pcs_misc;
 	u32 intr_mask;
 
-	if (qmp->mode == PHY_MODE_USB_HOST_SS ||
-	    qmp->mode == PHY_MODE_USB_DEVICE_SS)
+	if (qmp->phy_mode == PHY_MODE_USB_HOST_SS ||
+	    qmp->phy_mode == PHY_MODE_USB_DEVICE_SS)
 		intr_mask = ARCVR_DTCT_EN | ALFPS_DTCT_EN;
 	else
 		intr_mask = ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL;
@@ -3355,7 +3355,7 @@ static int __maybe_unused qmp_combo_runtime_suspend(struct device *dev)
 {
 	struct qmp_combo *qmp = dev_get_drvdata(dev);
 
-	dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->mode);
+	dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->phy_mode);
 
 	if (!qmp->init_count) {
 		dev_vdbg(dev, "PHY not initialized, bailing out\n");
@@ -3375,7 +3375,7 @@ static int __maybe_unused qmp_combo_runtime_resume(struct device *dev)
 	struct qmp_combo *qmp = dev_get_drvdata(dev);
 	int ret = 0;
 
-	dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->mode);
+	dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->phy_mode);
 
 	if (!qmp->init_count) {
 		dev_vdbg(dev, "PHY not initialized, bailing out\n");

-- 
2.50.1

[PATCH v4 3/6] phy: qcom: qmp-combo: store DP phy power state

[Konrad Dybcio]

From: Neil Armstrong <neil.armstrong@linaro.org>

Switching the PHY Mode requires the DisplayPort PHY to be powered off,
keep track of the DisplayPort phy power state.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index 30749943f66280c3aa9e9673466f6f736d1adbc8..8395035754975808ee1b5b9c48d046a719e79e60 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -1853,6 +1853,7 @@ struct qmp_combo {
 	unsigned int dp_aux_cfg;
 	struct phy_configure_opts_dp dp_opts;
 	unsigned int dp_init_count;
+	bool dp_powered_on;
 
 	struct clk_fixed_rate pipe_clk_fixed;
 	struct clk_hw dp_link_hw;
@@ -3133,6 +3134,8 @@ static int qmp_combo_dp_power_on(struct phy *phy)
 	/* Configure link rate, swing, etc. */
 	cfg->configure_dp_phy(qmp);
 
+	qmp->dp_powered_on = true;
+
 	mutex_unlock(&qmp->phy_mutex);
 
 	return 0;
@@ -3147,6 +3150,8 @@ static int qmp_combo_dp_power_off(struct phy *phy)
 	/* Assert DP PHY power down */
 	writel(DP_PHY_PD_CTL_PSR_PWRDN, qmp->dp_dp_phy + QSERDES_DP_PHY_PD_CTL);
 
+	qmp->dp_powered_on = false;
+
 	mutex_unlock(&qmp->phy_mutex);
 
 	return 0;

-- 
2.50.1

[PATCH v4 4/6] phy: qcom: qmp-combo: introduce QMPPHY_MODE

[Konrad Dybcio]

From: Neil Armstrong <neil.armstrong@linaro.org>

Introduce an enum for the QMP Combo PHY modes, use it in the
QMP commmon phy init function and default to COMBO mode.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[konrad: some renaming and rewording]
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 44 +++++++++++++++++++++++++++----
 1 file changed, 39 insertions(+), 5 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index 8395035754975808ee1b5b9c48d046a719e79e60..c65837fc9e4c38673fc61d3ae66072ba5a265a70 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -62,6 +62,12 @@
 
 #define PHY_INIT_COMPLETE_TIMEOUT		10000
 
+enum qmpphy_mode {
+	QMPPHY_MODE_USB3DP = 0,
+	QMPPHY_MODE_DP_ONLY,
+	QMPPHY_MODE_USB3_ONLY,
+};
+
 /* set of registers with offsets different per-PHY */
 enum qphy_reg_layout {
 	/* PCS registers */
@@ -1844,6 +1850,7 @@ struct qmp_combo {
 
 	struct mutex phy_mutex;
 	int init_count;
+	enum qmpphy_mode qmpphy_mode;
 
 	struct phy *usb_phy;
 	enum phy_mode phy_mode;
@@ -3037,12 +3044,33 @@ static int qmp_combo_com_init(struct qmp_combo *qmp, bool force)
 	if (qmp->orientation == TYPEC_ORIENTATION_REVERSE)
 		val |= SW_PORTSELECT_VAL;
 	writel(val, com + QPHY_V3_DP_COM_TYPEC_CTRL);
-	writel(USB3_MODE | DP_MODE, com + QPHY_V3_DP_COM_PHY_MODE_CTRL);
 
-	/* bring both QMP USB and QMP DP PHYs PCS block out of reset */
-	qphy_clrbits(com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
-			SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
-			SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+	switch (qmp->qmpphy_mode) {
+	case QMPPHY_MODE_USB3DP:
+		writel(USB3_MODE | DP_MODE, com + QPHY_V3_DP_COM_PHY_MODE_CTRL);
+
+		/* bring both QMP USB and QMP DP PHYs PCS block out of reset */
+		qphy_clrbits(com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+				SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+				SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+		break;
+
+	case QMPPHY_MODE_DP_ONLY:
+		writel(DP_MODE, com + QPHY_V3_DP_COM_PHY_MODE_CTRL);
+
+		/* bring QMP DP PHY PCS block out of reset */
+		qphy_clrbits(com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+				SW_DPPHY_RESET_MUX | SW_DPPHY_RESET);
+		break;
+
+	case QMPPHY_MODE_USB3_ONLY:
+		writel(USB3_MODE, com + QPHY_V3_DP_COM_PHY_MODE_CTRL);
+
+		/* bring QMP USB PHY PCS block out of reset */
+		qphy_clrbits(com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+				SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+		break;
+	}
 
 	qphy_clrbits(com, QPHY_V3_DP_COM_SWI_CTRL, 0x03);
 	qphy_clrbits(com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
@@ -4053,6 +4081,12 @@ static int qmp_combo_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_node_put;
 
+	/*
+	 * The hw default is USB3_ONLY, but USB3+DP mode lets us more easily
+	 * check both sub-blocks' init tables for blunders at probe time.
+	 */
+	qmp->qmpphy_mode = QMPPHY_MODE_USB3DP;
+
 	qmp->usb_phy = devm_phy_create(dev, usb_np, &qmp_combo_usb_phy_ops);
 	if (IS_ERR(qmp->usb_phy)) {
 		ret = PTR_ERR(qmp->usb_phy);

-- 
2.50.1

[PATCH v4 5/6] phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE

[Konrad Dybcio]

From: Neil Armstrong <neil.armstrong@linaro.org>

Register a typec mux in order to change the PHY mode on the Type-C
mux events depending on the mode and the svid when in Altmode setup.

The DisplayPort phy should be left enabled if is still powered on
by the DRM DisplayPort controller, so bail out until the DisplayPort
PHY is not powered off.

The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
will be set in between of USB-Only, Combo and DisplayPort Only so
this will leave enough time to the DRM DisplayPort controller to
turn of the DisplayPort PHY.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[konrad: renaming, rewording, bug fixes]
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 118 ++++++++++++++++++++++++++++--
 1 file changed, 113 insertions(+), 5 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index c65837fc9e4c38673fc61d3ae66072ba5a265a70..7b5af30f1d028c592500e723ecd27b54ed554709 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -19,6 +19,7 @@
 #include <linux/reset.h>
 #include <linux/slab.h>
 #include <linux/usb/typec.h>
+#include <linux/usb/typec_dp.h>
 #include <linux/usb/typec_mux.h>
 
 #include <drm/bridge/aux-bridge.h>
@@ -1868,6 +1869,8 @@ struct qmp_combo {
 
 	struct typec_switch_dev *sw;
 	enum typec_orientation orientation;
+
+	struct typec_mux_dev *mux;
 };
 
 static void qmp_v3_dp_aux_init(struct qmp_combo *qmp);
@@ -3802,17 +3805,109 @@ static int qmp_combo_typec_switch_set(struct typec_switch_dev *sw,
 	return 0;
 }
 
-static void qmp_combo_typec_unregister(void *data)
+static int qmp_combo_typec_mux_set(struct typec_mux_dev *mux, struct typec_mux_state *state)
+{
+	struct qmp_combo *qmp = typec_mux_get_drvdata(mux);
+	const struct qmp_phy_cfg *cfg = qmp->cfg;
+	enum qmpphy_mode new_mode;
+	unsigned int svid;
+
+	guard(mutex)(&qmp->phy_mutex);
+
+	if (state->alt)
+		svid = state->alt->svid;
+	else
+		svid = 0;
+
+	if (svid == USB_TYPEC_DP_SID) {
+		switch (state->mode) {
+		/* DP Only */
+		case TYPEC_DP_STATE_C:
+		case TYPEC_DP_STATE_E:
+			new_mode = QMPPHY_MODE_DP_ONLY;
+			break;
+
+		/* DP + USB */
+		case TYPEC_DP_STATE_D:
+		case TYPEC_DP_STATE_F:
+
+		/* Safe fallback...*/
+		default:
+			new_mode = QMPPHY_MODE_USB3DP;
+			break;
+		}
+	} else {
+		/* No DP SVID => don't care, assume it's just USB3 */
+		new_mode = QMPPHY_MODE_USB3_ONLY;
+	}
+
+	if (new_mode == qmp->qmpphy_mode) {
+		dev_dbg(qmp->dev, "typec_mux_set: same qmpphy mode, bail out\n");
+		return 0;
+	}
+
+	if (qmp->qmpphy_mode != QMPPHY_MODE_USB3_ONLY && qmp->dp_powered_on) {
+		dev_dbg(qmp->dev, "typec_mux_set: DP PHY is still in use, delaying switch\n");
+		return 0;
+	}
+
+	dev_dbg(qmp->dev, "typec_mux_set: switching from qmpphy mode %d to %d\n",
+		qmp->qmpphy_mode, new_mode);
+
+	qmp->qmpphy_mode = new_mode;
+
+	if (qmp->init_count) {
+		if (qmp->usb_init_count)
+			qmp_combo_usb_power_off(qmp->usb_phy);
+
+		if (qmp->dp_init_count)
+			writel(DP_PHY_PD_CTL_PSR_PWRDN, qmp->dp_dp_phy + QSERDES_DP_PHY_PD_CTL);
+
+		qmp_combo_com_exit(qmp, true);
+
+		/* Now everything's powered down, power up the right PHYs */
+		qmp_combo_com_init(qmp, true);
+
+		if (new_mode == QMPPHY_MODE_DP_ONLY) {
+			if (qmp->usb_init_count)
+				qmp->usb_init_count--;
+		}
+
+		if (new_mode == QMPPHY_MODE_USB3DP || new_mode == QMPPHY_MODE_USB3_ONLY) {
+			qmp_combo_usb_power_on(qmp->usb_phy);
+			if (!qmp->usb_init_count)
+				qmp->usb_init_count++;
+		}
+
+		if (new_mode == QMPPHY_MODE_DP_ONLY || new_mode == QMPPHY_MODE_USB3DP) {
+			if (qmp->dp_init_count)
+				cfg->dp_aux_init(qmp);
+		}
+	}
+
+	return 0;
+}
+
+static void qmp_combo_typec_switch_unregister(void *data)
 {
 	struct qmp_combo *qmp = data;
 
 	typec_switch_unregister(qmp->sw);
 }
 
-static int qmp_combo_typec_switch_register(struct qmp_combo *qmp)
+static void qmp_combo_typec_mux_unregister(void *data)
+{
+	struct qmp_combo *qmp = data;
+
+	typec_mux_unregister(qmp->mux);
+}
+
+static int qmp_combo_typec_register(struct qmp_combo *qmp)
 {
 	struct typec_switch_desc sw_desc = {};
+	struct typec_mux_desc mux_desc = { };
 	struct device *dev = qmp->dev;
+	int ret;
 
 	sw_desc.drvdata = qmp;
 	sw_desc.fwnode = dev->fwnode;
@@ -3823,10 +3918,23 @@ static int qmp_combo_typec_switch_register(struct qmp_combo *qmp)
 		return PTR_ERR(qmp->sw);
 	}
 
-	return devm_add_action_or_reset(dev, qmp_combo_typec_unregister, qmp);
+	ret = devm_add_action_or_reset(dev, qmp_combo_typec_switch_unregister, qmp);
+	if (ret)
+		return ret;
+
+	mux_desc.drvdata = qmp;
+	mux_desc.fwnode = dev->fwnode;
+	mux_desc.set = qmp_combo_typec_mux_set;
+	qmp->mux = typec_mux_register(dev, &mux_desc);
+	if (IS_ERR(qmp->mux)) {
+		dev_err(dev, "Unable to register typec mux: %pe\n", qmp->mux);
+		return PTR_ERR(qmp->mux);
+	}
+
+	return devm_add_action_or_reset(dev, qmp_combo_typec_mux_unregister, qmp);
 }
 #else
-static int qmp_combo_typec_switch_register(struct qmp_combo *qmp)
+static int qmp_combo_typec_register(struct qmp_combo *qmp)
 {
 	return 0;
 }
@@ -4059,7 +4167,7 @@ static int qmp_combo_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_node_put;
 
-	ret = qmp_combo_typec_switch_register(qmp);
+	ret = qmp_combo_typec_register(qmp);
 	if (ret)
 		goto err_node_put;
 

-- 
2.50.1

[PATCH v4 6/6] arm64: dts: qcom: sc8280xp-lenovo-thinkpad-x13: Set up 4-lane DP

[Konrad Dybcio]

From: Neil Armstrong <neil.armstrong@linaro.org>

Allow up to 4 lanes for the DisplayPort link from the PHYs to the
controllers and allow mode-switch events to reach the QMP Combo PHYs.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
[konrad: reword]
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
index cefecb7a23cf579b1f62ef6fccf9a27a6ea92ac4..b298ec1162357f7f273cb603465dab8388d4b38c 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -726,7 +726,7 @@ &mdss0_dp0 {
 };
 
 &mdss0_dp0_out {
-	data-lanes = <0 1>;
+	data-lanes = <0 1 2 3>;
 	remote-endpoint = <&usb_0_qmpphy_dp_in>;
 };
 
@@ -735,7 +735,7 @@ &mdss0_dp1 {
 };
 
 &mdss0_dp1_out {
-	data-lanes = <0 1>;
+	data-lanes = <0 1 2 3>;
 	remote-endpoint = <&usb_1_qmpphy_dp_in>;
 };
 
@@ -1360,6 +1360,7 @@ &usb_0_qmpphy {
 	vdda-phy-supply = <&vreg_l9d>;
 	vdda-pll-supply = <&vreg_l4d>;
 
+	mode-switch;
 	orientation-switch;
 
 	status = "okay";
@@ -1397,6 +1398,7 @@ &usb_1_qmpphy {
 	vdda-phy-supply = <&vreg_l4b>;
 	vdda-pll-supply = <&vreg_l3b>;
 
+	mode-switch;
 	orientation-switch;
 
 	status = "okay";

-- 
2.50.1

Re: [PATCH v4 0/6] arm64: qcom: allow up to 4 lanes for the Type-C DisplayPort Altmode

[Rob Herring (Arm)]

On Thu, 07 Aug 2025 18:33:18 +0200, Konrad Dybcio wrote:
> Register a typec mux in order to change the PHY mode on the Type-C
> mux events depending on the mode and the svid when in Altmode setup.
> 
> The DisplayPort phy should be left enabled if is still powered on
> by the DRM DisplayPort controller, so bail out until the DisplayPort
> PHY is not powered off.
> 
> The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
> will be set in between of USB-Only, Combo and DisplayPort Only so
> this will leave enough time to the DRM DisplayPort controller to
> turn of the DisplayPort PHY.
> 
> The patchset also includes bindings changes and DT changes.
> 
> This has been successfully tested on an SM8550 board, but the
> Thinkpad X13s deserved testing between non-PD USB, non-PD DisplayPort,
> PD USB Hubs and PD Altmode Dongles to make sure the switch works
> as expected.
> 
> The DisplayPort 4 lanes setup can be check with:
> $ cat /sys/kernel/debug/dri/ae01000.display-controller/DP-1/dp_debug
> 	name = msm_dp
> 	drm_dp_link
> 		rate = 540000
> 		num_lanes = 4
> ...
> 
> This patchset depends on [1] to allow broadcasting the type-c mode
> to the PHY, otherwise the PHY will keep the combo state while the
> retimer would setup the 4 lanes in DP mode.
> 
> [1] https://lore.kernel.org/all/20240527-topic-sm8x50-upstream-retimer-broadcast-mode-v1-0-79ec91381aba@linaro.org/
> 
> Changes in v4:
> - Default to USB3_ONLY if there's no DP SVID (Dmitry)
> - Pick up tags, dropped T-bys due to the above change
> - Add missing submitter's sign-off on some patches
> - The odd 4-lane-DP + USB2 case remains unhandled for now, but it's
>   not a huge deal, see:
>   <c2f2ba36-1a25-450e-99b9-79aa4fd4913d@linaro.org>
> - Link to v3: https://lore.kernel.org/r/20250527-topic-4ln_dp_respin-v3-0-f9a0763ec289@oss.qualcomm.com
> Changes in v3:
> - Take the series from Neil
> - Rebase
> - Rename many variables
> - Test on X1E & X13s
> - Apply a number of small cosmetic/codestyle changes
> - Remove some unused variables
> - Some smaller bugfixes
> - Link to v2: https://lore.kernel.org/lkml/20240527-topic-sm8x50-upstream-phy-combo-typec-mux-v2-0-a03e68d7b8fc@linaro.org/
> Changes in v2:
> - Reference usb-switch.yaml in bindings patch
> - Fix switch/case indenting
> - Check svid for USB_TYPEC_DP_SID
> - Fix X13s patch subject
> - Update SM8650 patch to enable 4 lanes on HDK aswell
> - Link to v1: https://lore.kernel.org/r/20240229-topic-sm8x50-upstream-phy-combo-typec-mux-v1-0-07e24a231840@linaro.org
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
> Konrad Dybcio (1):
>       phy: qcom: qmp-combo: Rename 'mode' to 'phy_mode'
> 
> Neil Armstrong (5):
>       dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch
>       phy: qcom: qmp-combo: store DP phy power state
>       phy: qcom: qmp-combo: introduce QMPPHY_MODE
>       phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE
>       arm64: dts: qcom: sc8280xp-lenovo-thinkpad-x13: Set up 4-lane DP
> 
>  .../phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml         |   7 +-
>  .../dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts     |   6 +-
>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c          | 179 +++++++++++++++++++--
>  3 files changed, 170 insertions(+), 22 deletions(-)
> ---
> base-commit: 442d93313caebc8ccd6d53f4572c50732a95bc48
> change-id: 20250527-topic-4ln_dp_respin-c6924a8825ce
> 
> Best regards,
> --
> Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: using specified base-commit 442d93313caebc8ccd6d53f4572c50732a95bc48

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20250807-topic-4ln_dp_respin-v4-0-43272d6eca92@oss.qualcomm.com:

arch/arm64/boot/dts/qcom/sm7125-xiaomi-curtana.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r4.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel360-wifi.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r10.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r9.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r4.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r9.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel360-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1-kb.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r10-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-idp.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r10.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-kb.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-parade.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-ti.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r3-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r3.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-r1-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-ti.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r3.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx-rt5682s.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-parade.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r5.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r10-kb.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r3-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sm7125-xiaomi-joyeuse.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r10.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#
arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dtb: phy@88e8000 (qcom,sc7180-qmp-usb3-dp-phy): 'oneOf' conditional failed, one must be fixed:
	'port' is a required property
	'ports' is a required property
	from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml#

Re: [PATCH v4 4/6] phy: qcom: qmp-combo: introduce QMPPHY_MODE

[Dmitry Baryshkov]

On Thu, Aug 07, 2025 at 06:33:22PM +0200, Konrad Dybcio wrote:
> From: Neil Armstrong <neil.armstrong@linaro.org>
> 
> Introduce an enum for the QMP Combo PHY modes, use it in the
> QMP commmon phy init function and default to COMBO mode.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> [konrad: some renaming and rewording]
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 44 +++++++++++++++++++++++++++----
>  1 file changed, 39 insertions(+), 5 deletions(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v4 5/6] phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE

[Dmitry Baryshkov]

On Thu, Aug 07, 2025 at 06:33:23PM +0200, Konrad Dybcio wrote:
> From: Neil Armstrong <neil.armstrong@linaro.org>
> 
> Register a typec mux in order to change the PHY mode on the Type-C
> mux events depending on the mode and the svid when in Altmode setup.
> 
> The DisplayPort phy should be left enabled if is still powered on
> by the DRM DisplayPort controller, so bail out until the DisplayPort
> PHY is not powered off.
> 
> The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
> will be set in between of USB-Only, Combo and DisplayPort Only so
> this will leave enough time to the DRM DisplayPort controller to
> turn of the DisplayPort PHY.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> [konrad: renaming, rewording, bug fixes]
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 118 ++++++++++++++++++++++++++++--
>  1 file changed, 113 insertions(+), 5 deletions(-)
> 
> +
> +	if (qmp->qmpphy_mode != QMPPHY_MODE_USB3_ONLY && qmp->dp_powered_on) {
> +		dev_dbg(qmp->dev, "typec_mux_set: DP PHY is still in use, delaying switch\n");
> +		return 0;
> +	}

I can't say that I'm fully happy about it, nevertheless:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v4 2/6] phy: qcom: qmp-combo: Rename 'mode' to 'phy_mode'

[Neil Armstrong]

On 07/08/2025 18:33, Konrad Dybcio wrote:
> From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> 
> There are a numbers of ""modes"" involved: USB mode, Type-C mode (with
> its altmodes), phy_mode and QMP_PHY mode (DP/combo/USB/off).
> 
> Rename the generic sounding 'mode' to 'phy_mode' to hopefully make
> the code easier to follow.
> 
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 12 ++++++------
>   1 file changed, 6 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> index f07d097b129fb7b3fad003103b7468b16c1c4390..30749943f66280c3aa9e9673466f6f736d1adbc8 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> @@ -1846,7 +1846,7 @@ struct qmp_combo {
>   	int init_count;
>   
>   	struct phy *usb_phy;
> -	enum phy_mode mode;
> +	enum phy_mode phy_mode;
>   	unsigned int usb_init_count;
>   
>   	struct phy *dp_phy;
> @@ -3282,7 +3282,7 @@ static int qmp_combo_usb_set_mode(struct phy *phy, enum phy_mode mode, int submo
>   {
>   	struct qmp_combo *qmp = phy_get_drvdata(phy);
>   
> -	qmp->mode = mode;
> +	qmp->phy_mode = mode;
>   
>   	return 0;
>   }
> @@ -3311,8 +3311,8 @@ static void qmp_combo_enable_autonomous_mode(struct qmp_combo *qmp)
>   	void __iomem *pcs_misc = qmp->pcs_misc;
>   	u32 intr_mask;
>   
> -	if (qmp->mode == PHY_MODE_USB_HOST_SS ||
> -	    qmp->mode == PHY_MODE_USB_DEVICE_SS)
> +	if (qmp->phy_mode == PHY_MODE_USB_HOST_SS ||
> +	    qmp->phy_mode == PHY_MODE_USB_DEVICE_SS)
>   		intr_mask = ARCVR_DTCT_EN | ALFPS_DTCT_EN;
>   	else
>   		intr_mask = ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL;
> @@ -3355,7 +3355,7 @@ static int __maybe_unused qmp_combo_runtime_suspend(struct device *dev)
>   {
>   	struct qmp_combo *qmp = dev_get_drvdata(dev);
>   
> -	dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->mode);
> +	dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->phy_mode);
>   
>   	if (!qmp->init_count) {
>   		dev_vdbg(dev, "PHY not initialized, bailing out\n");
> @@ -3375,7 +3375,7 @@ static int __maybe_unused qmp_combo_runtime_resume(struct device *dev)
>   	struct qmp_combo *qmp = dev_get_drvdata(dev);
>   	int ret = 0;
>   
> -	dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->mode);
> +	dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->phy_mode);
>   
>   	if (!qmp->init_count) {
>   		dev_vdbg(dev, "PHY not initialized, bailing out\n");
> 

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

Re: [PATCH v4 5/6] phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE

[Konrad Dybcio]

On 8/9/25 10:13 AM, Dmitry Baryshkov wrote:
> On Thu, Aug 07, 2025 at 06:33:23PM +0200, Konrad Dybcio wrote:
>> From: Neil Armstrong <neil.armstrong@linaro.org>
>>
>> Register a typec mux in order to change the PHY mode on the Type-C
>> mux events depending on the mode and the svid when in Altmode setup.
>>
>> The DisplayPort phy should be left enabled if is still powered on
>> by the DRM DisplayPort controller, so bail out until the DisplayPort
>> PHY is not powered off.
>>
>> The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
>> will be set in between of USB-Only, Combo and DisplayPort Only so
>> this will leave enough time to the DRM DisplayPort controller to
>> turn of the DisplayPort PHY.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> [konrad: renaming, rewording, bug fixes]
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
>> ---
>>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 118 ++++++++++++++++++++++++++++--
>>  1 file changed, 113 insertions(+), 5 deletions(-)
>>
>> +
>> +	if (qmp->qmpphy_mode != QMPPHY_MODE_USB3_ONLY && qmp->dp_powered_on) {
>> +		dev_dbg(qmp->dev, "typec_mux_set: DP PHY is still in use, delaying switch\n");
>> +		return 0;
>> +	}
> 
> I can't say that I'm fully happy about it, nevertheless:
> 
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>

IIUC we'll be able to get rid of it after the dp rework?

Konrad

Re: [PATCH v4 5/6] phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE

[Dmitry Baryshkov]

On Mon, Aug 11, 2025 at 12:37:00PM +0200, Konrad Dybcio wrote:
> On 8/9/25 10:13 AM, Dmitry Baryshkov wrote:
> > On Thu, Aug 07, 2025 at 06:33:23PM +0200, Konrad Dybcio wrote:
> >> From: Neil Armstrong <neil.armstrong@linaro.org>
> >>
> >> Register a typec mux in order to change the PHY mode on the Type-C
> >> mux events depending on the mode and the svid when in Altmode setup.
> >>
> >> The DisplayPort phy should be left enabled if is still powered on
> >> by the DRM DisplayPort controller, so bail out until the DisplayPort
> >> PHY is not powered off.
> >>
> >> The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
> >> will be set in between of USB-Only, Combo and DisplayPort Only so
> >> this will leave enough time to the DRM DisplayPort controller to
> >> turn of the DisplayPort PHY.
> >>
> >> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> >> [konrad: renaming, rewording, bug fixes]
> >> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> >> ---
> >>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 118 ++++++++++++++++++++++++++++--
> >>  1 file changed, 113 insertions(+), 5 deletions(-)
> >>
> >> +
> >> +	if (qmp->qmpphy_mode != QMPPHY_MODE_USB3_ONLY && qmp->dp_powered_on) {
> >> +		dev_dbg(qmp->dev, "typec_mux_set: DP PHY is still in use, delaying switch\n");
> >> +		return 0;
> >> +	}
> > 
> > I can't say that I'm fully happy about it, nevertheless:
> > 
> > Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
> 
> IIUC we'll be able to get rid of it after the dp rework?

Which one? The HPD? not really. My unhappiness is about the sync between
USB and DP. I'm unsure whether we need higher level of sync for
USB-or-DP PHYs.

-- 
With best wishes
Dmitry

Re: [PATCH v4 5/6] phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE

[Konrad Dybcio]

On 8/11/25 12:55 PM, Dmitry Baryshkov wrote:
> On Mon, Aug 11, 2025 at 12:37:00PM +0200, Konrad Dybcio wrote:
>> On 8/9/25 10:13 AM, Dmitry Baryshkov wrote:
>>> On Thu, Aug 07, 2025 at 06:33:23PM +0200, Konrad Dybcio wrote:
>>>> From: Neil Armstrong <neil.armstrong@linaro.org>
>>>>
>>>> Register a typec mux in order to change the PHY mode on the Type-C
>>>> mux events depending on the mode and the svid when in Altmode setup.
>>>>
>>>> The DisplayPort phy should be left enabled if is still powered on
>>>> by the DRM DisplayPort controller, so bail out until the DisplayPort
>>>> PHY is not powered off.
>>>>
>>>> The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
>>>> will be set in between of USB-Only, Combo and DisplayPort Only so
>>>> this will leave enough time to the DRM DisplayPort controller to
>>>> turn of the DisplayPort PHY.
>>>>
>>>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>>>> [konrad: renaming, rewording, bug fixes]
>>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
>>>> ---
>>>>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 118 ++++++++++++++++++++++++++++--
>>>>  1 file changed, 113 insertions(+), 5 deletions(-)
>>>>
>>>> +
>>>> +	if (qmp->qmpphy_mode != QMPPHY_MODE_USB3_ONLY && qmp->dp_powered_on) {
>>>> +		dev_dbg(qmp->dev, "typec_mux_set: DP PHY is still in use, delaying switch\n");
>>>> +		return 0;
>>>> +	}
>>>
>>> I can't say that I'm fully happy about it, nevertheless:
>>>
>>> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
>>
>> IIUC we'll be able to get rid of it after the dp rework?
> 
> Which one? The HPD? not really. My unhappiness is about the sync between
> USB and DP. I'm unsure whether we need higher level of sync for
> USB-or-DP PHYs.

Unfortunately it'll only get worse with usb4, where the DP PLL may
need to be online (or not) for when we're tunneling DP data :(

Konrad

Re: [PATCH v4 0/6] arm64: qcom: allow up to 4 lanes for the Type-C DisplayPort Altmode

[Neil Armstrong]

On 07/08/2025 18:33, Konrad Dybcio wrote:
> Register a typec mux in order to change the PHY mode on the Type-C
> mux events depending on the mode and the svid when in Altmode setup.
> 
> The DisplayPort phy should be left enabled if is still powered on
> by the DRM DisplayPort controller, so bail out until the DisplayPort
> PHY is not powered off.
> 
> The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
> will be set in between of USB-Only, Combo and DisplayPort Only so
> this will leave enough time to the DRM DisplayPort controller to
> turn of the DisplayPort PHY.
> 
> The patchset also includes bindings changes and DT changes.
> 
> This has been successfully tested on an SM8550 board, but the
> Thinkpad X13s deserved testing between non-PD USB, non-PD DisplayPort,
> PD USB Hubs and PD Altmode Dongles to make sure the switch works
> as expected.
> 
> The DisplayPort 4 lanes setup can be check with:
> $ cat /sys/kernel/debug/dri/ae01000.display-controller/DP-1/dp_debug
> 	name = msm_dp
> 	drm_dp_link
> 		rate = 540000
> 		num_lanes = 4
> ...
> 
> This patchset depends on [1] to allow broadcasting the type-c mode
> to the PHY, otherwise the PHY will keep the combo state while the
> retimer would setup the 4 lanes in DP mode.
> 
> [1] https://lore.kernel.org/all/20240527-topic-sm8x50-upstream-retimer-broadcast-mode-v1-0-79ec91381aba@linaro.org/
> 
> Changes in v4:
> - Default to USB3_ONLY if there's no DP SVID (Dmitry)
> - Pick up tags, dropped T-bys due to the above change
> - Add missing submitter's sign-off on some patches
> - The odd 4-lane-DP + USB2 case remains unhandled for now, but it's
>    not a huge deal, see:
>    <c2f2ba36-1a25-450e-99b9-79aa4fd4913d@linaro.org>
> - Link to v3: https://lore.kernel.org/r/20250527-topic-4ln_dp_respin-v3-0-f9a0763ec289@oss.qualcomm.com
> Changes in v3:
> - Take the series from Neil
> - Rebase
> - Rename many variables
> - Test on X1E & X13s
> - Apply a number of small cosmetic/codestyle changes
> - Remove some unused variables
> - Some smaller bugfixes
> - Link to v2: https://lore.kernel.org/lkml/20240527-topic-sm8x50-upstream-phy-combo-typec-mux-v2-0-a03e68d7b8fc@linaro.org/
> Changes in v2:
> - Reference usb-switch.yaml in bindings patch
> - Fix switch/case indenting
> - Check svid for USB_TYPEC_DP_SID
> - Fix X13s patch subject
> - Update SM8650 patch to enable 4 lanes on HDK aswell
> - Link to v1: https://lore.kernel.org/r/20240229-topic-sm8x50-upstream-phy-combo-typec-mux-v1-0-07e24a231840@linaro.org
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
> Konrad Dybcio (1):
>        phy: qcom: qmp-combo: Rename 'mode' to 'phy_mode'
> 
> Neil Armstrong (5):
>        dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch
>        phy: qcom: qmp-combo: store DP phy power state
>        phy: qcom: qmp-combo: introduce QMPPHY_MODE
>        phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE
>        arm64: dts: qcom: sc8280xp-lenovo-thinkpad-x13: Set up 4-lane DP
> 
>   .../phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml         |   7 +-
>   .../dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts     |   6 +-
>   drivers/phy/qualcomm/phy-qcom-qmp-combo.c          | 179 +++++++++++++++++++--
>   3 files changed, 170 insertions(+), 22 deletions(-)
> ---
> base-commit: 442d93313caebc8ccd6d53f4572c50732a95bc48
> change-id: 20250527-topic-4ln_dp_respin-c6924a8825ce
> 
> Best regards,

Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S

Successfully got 4 lanes working with an USB-C to DP adapter with either orientation:
	dp_link:
		test_requested = 512
		num_lanes = 4
		bw_code = 20
		lclk = 540000000
		v_level = 2
		p_level = 0

And 2 lanes is still working.

I'll test on SM8550/SM8650 later this week.

Thanks,
Neil

Re: (subset) [PATCH v4 0/6] arm64: qcom: allow up to 4 lanes for the Type-C DisplayPort Altmode

[Vinod Koul]

On Thu, 07 Aug 2025 18:33:18 +0200, Konrad Dybcio wrote:
> Register a typec mux in order to change the PHY mode on the Type-C
> mux events depending on the mode and the svid when in Altmode setup.
> 
> The DisplayPort phy should be left enabled if is still powered on
> by the DRM DisplayPort controller, so bail out until the DisplayPort
> PHY is not powered off.
> 
> [...]

Applied, thanks!

[1/6] dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch
      commit: 3bad7fe22796a420c6e16b591c37ed1bd6cc2a30
[2/6] phy: qcom: qmp-combo: Rename 'mode' to 'phy_mode'
      commit: 5daf1bbc73e249075373e030e7221f46c175e04b
[3/6] phy: qcom: qmp-combo: store DP phy power state
      commit: 86390472554b2e8fb4cba16a139cade94be58f72
[4/6] phy: qcom: qmp-combo: introduce QMPPHY_MODE
      commit: dd331112c0adaebbc8fc767fc805da4a641576db
[5/6] phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE
      commit: 896277138c1344cf9f5c415298f048ee29da274d

Best regards,
-- 
~Vinod

Re: [PATCH v4 1/6] dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch

[Rob Herring]

On Thu, Aug 07, 2025 at 06:33:19PM +0200, Konrad Dybcio wrote:
> From: Neil Armstrong <neil.armstrong@linaro.org>
> 
> The QMP USB3/DP Combo PHY can work in 3 modes:
> - DisplayPort Only
> - USB3 Only
> - USB3 + DisplayPort Combo mode
> 
> In order to switch between those modes, the PHY needs to receive
> Type-C events, allow marking to the phy with the mode-switch
> property in order to allow the PHY to Type-C events.
> 
> Reference usb-switch.yaml as a simpler way to allow the mode-switch
> property instead of duplicating the property definition.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
>  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml     | 7 +++----
>  1 file changed, 3 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
> index 38ce04c35d945d0d8d319191c241920810ee9005..c8bc512df08b5694c8599f475de78679a4438449 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
> @@ -73,10 +73,8 @@ properties:
>      description:
>        See include/dt-bindings/phy/phy-qcom-qmp.h
>  
> -  orientation-switch:
> -    description:
> -      Flag the PHY as possible handler of USB Type-C orientation switching
> -    type: boolean
> +  mode-switch: true
> +  orientation-switch: true
>  
>    ports:
>      $ref: /schemas/graph.yaml#/properties/ports
> @@ -106,6 +104,7 @@ required:
>    - "#phy-cells"
>  
>  allOf:
> +  - $ref: /schemas/usb/usb-switch.yaml#

As reported already in this thread, this adds a crap load of warnings as 
it makes ports or port required. Sigh. Can QCom folks pay more attention 
to this please. Every cycle the number goes up though that's often 
temporary because there's no coordination of taking .dts files after 
bindings. But generally, progress on QCom warnings has stalled.

Here's the top (bottom?) platforms in arm64. The first number is 
total warnings. The 2nd number is unique warnings (to remove inflated 
numbers due to lots of boards per SoC).

mediatek:785:166
hisilicon:133:112
qcom:362:104
broadcom:286:104
marvell:558:80
apm:78:58
rockchip:128:57
nvidia:199:53
sprd:30:29
xilinx:94:22

Congrats on 3rd place. There's a bunch of pending Mediatek fixes, so I 
expect you all will move up to 2nd soon. 

All this data is updated daily. There's some scripts to get and process 
the logs here[1].

Rob

[1] https://gitlab.com/robherring/ci-jobs.git

Re: (subset) [PATCH v4 0/6] arm64: qcom: allow up to 4 lanes for the Type-C DisplayPort Altmode

[Bjorn Andersson]

On Thu, 07 Aug 2025 18:33:18 +0200, Konrad Dybcio wrote:
> Register a typec mux in order to change the PHY mode on the Type-C
> mux events depending on the mode and the svid when in Altmode setup.
> 
> The DisplayPort phy should be left enabled if is still powered on
> by the DRM DisplayPort controller, so bail out until the DisplayPort
> PHY is not powered off.
> 
> [...]

Applied, thanks!

[6/6] arm64: dts: qcom: sc8280xp-lenovo-thinkpad-x13: Set up 4-lane DP
      commit: 7a6ad5dd551a20672edceed087408ea6bcbfe8f2

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>