[PATCH v7 0/2] Add support for Texas Instruments DTHEv2 Crypto Engine

[PATCH v7 0/2] Add support for Texas Instruments DTHEv2 Crypto Engine

[T Pratham]

Data Transform and Hashing Engine (DTHE) v2 is a new cryptography engine
introduced i TI AM62L SoC. DTHEv2 consists of multiple crypto IPs[1] (such
as AES Engine, hashing engine, TRNG, etc.) which can be used for
offloading cryptographic operations off of the CPU. The primary benefit
of DTHEv2 is enhanced side-channel attack resistance, with AES and PKE
engine being DPA and EMA resistant. These side-channel resistances are
the underlying requirement for various certifications like SESIP, PSA,
and IEC62443 (lvl 3+). Thus, DTHEv2 provides critical security benefits
for embedded systems that require protection against passive physical
attacks.

The AES Engine of DTHEv2 supports multiple AES modes (ECB, CBC, CTR,
CFB, f8), several protocols (GCM, CCM, XTS) and authentication modes
(CBC-MAC and f9). The hashing engine supports MD5, SHA1, and SHA2 (224,
256, 384, 512) algorithms along with HMAC. This patch series introduces
basic driver support for DTHEv2 engine, beginning with suporting AES-ECB
and AES-CBC algorithms. Other algorithms are planned to be added
gradually in phases after initial suppport is added.

The driver is tested using full kernel crypto selftests (CRYPTO_SELFTESTS)
which all pass successfully [2].

Signed-off-by: T Pratham <t-pratham@ti.com>
---
[1]: Section 14.6.3 (DMA Control Registers -> DMASS_DTHE)
Link: https://www.ti.com/lit/ug/sprujb4/sprujb4.pdf

[2]: DTHEv2 AES-ECB and AES-CBC kernel self-tests logs
Link: https://gist.github.com/Pratham-T/aaa499cf50d20310cb27266a645bfd60

Change log:
v7:
 - Dropped redundant crypto_engine_stop() calls.
 - Corrected Reviewed-by tag.
v6:
 - Reworded the cover letter and commit messages to name DTHEv2 as a
   crypto engine instead of crypto accelerator.
 - Reworded the cover letter completely to emphasise more on the utility
   of DTHEv2 as better resistance against physical attacks
 - Reworded DTHEv2 description (help text) in KConfig
 - Added dma_terminate_sync calls to ensure DMA requests are removed in
   case when completion times-out.
 - Some rearrangement of fields between dthe_tfm_ctx and dthe_aes_req_ctx
   struct, so that per tfm members are correctly placed in tfm_ctx and per
   request members are in req_ctx. Subsequently setkey, encrypt and
   decrypt functions are also changed.
 - Removed exit_tfm function which was useless and not required.
 - Removed unnecessary zeroing of tfm_ctx object in init_tfm.
 - Corrected return value in dthe_aes_run function.
 - Reduced cra_priority of DTHEv2 algorithms.
v5:
 - Simplified tfm ctx struct
 - Set cra_reqsize instead of using crypto_skcipher_set_reqsize()
 - Move setting sysconfig and irqenable registers to dthe_aes_run
v4:
 - Corrected dt-bindings example indentation
 - Simplified dt-bindings example, removing the node surrounding crypto
 - Fixed typo in dthev2-common.h header guard
 - Removed unused ctx field in dev_data struct
 - Moved per-op data into request context
v3:
 - Corrected dt-bindings reg length is too long error
 - Converted AES driver code to use crypto_engine APIs for using
   internal crypto queue instead of mutex.
 - Removed calls to skcipher_request_complete in paths not returning
   -EINPROGRESS before.
 - Added missing KConfig import, which was accidentally removed in v2.

v2:
 - Corrected dt-bindings syntax errors and other review comments in v1.
 - Completely changed driver code structure, splitting code into
   multiple files

Link to previous versions:
v6: https://lore.kernel.org/all/20250819065844.3337101-1-t-pratham@ti.com/
v5: https://lore.kernel.org/all/20250603124217.957116-1-t-pratham@ti.com/
v4: https://lore.kernel.org/all/20250508101723.846210-2-t-pratham@ti.com/
v3: https://lore.kernel.org/all/20250502121253.456974-2-t-pratham@ti.com/
v2: https://lore.kernel.org/all/20250411091321.2925308-1-t-pratham@ti.com/
v1: https://lore.kernel.org/all/20250206-dthe-v2-aes-v1-0-1e86cf683928@ti.com/
---

T Pratham (2):
  dt-bindings: crypto: Add binding for TI DTHE V2
  crypto: ti: Add driver for DTHE V2 AES Engine (ECB, CBC)

 .../bindings/crypto/ti,am62l-dthev2.yaml      |  50 +++
 MAINTAINERS                                   |   7 +
 drivers/crypto/Kconfig                        |   1 +
 drivers/crypto/Makefile                       |   1 +
 drivers/crypto/ti/Kconfig                     |  14 +
 drivers/crypto/ti/Makefile                    |   3 +
 drivers/crypto/ti/dthev2-aes.c                | 411 ++++++++++++++++++
 drivers/crypto/ti/dthev2-common.c             | 217 +++++++++
 drivers/crypto/ti/dthev2-common.h             | 101 +++++
 9 files changed, 805 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml
 create mode 100644 drivers/crypto/ti/Kconfig
 create mode 100644 drivers/crypto/ti/Makefile
 create mode 100644 drivers/crypto/ti/dthev2-aes.c
 create mode 100644 drivers/crypto/ti/dthev2-common.c
 create mode 100644 drivers/crypto/ti/dthev2-common.h

-- 
2.43.0

[PATCH v7 1/2] dt-bindings: crypto: Add binding for TI DTHE V2

[T Pratham]

Add DT binding for Texas Instruments DTHE V2 cryptography engine.

DTHE V2 is introduced as a part of TI AM62L SoC and can currently be
only found in it.

Signed-off-by: T Pratham <t-pratham@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/crypto/ti,am62l-dthev2.yaml      | 50 +++++++++++++++++++
 MAINTAINERS                                   |  6 +++
 2 files changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml

diff --git a/Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml b/Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml
new file mode 100644
index 000000000000..5486bfeb2fe8
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/crypto/ti,am62l-dthev2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: K3 SoC DTHE V2 crypto module
+
+maintainers:
+  - T Pratham <t-pratham@ti.com>
+
+properties:
+  compatible:
+    enum:
+      - ti,am62l-dthev2
+
+  reg:
+    maxItems: 1
+
+  dmas:
+    items:
+      - description: AES Engine RX DMA Channel
+      - description: AES Engine TX DMA Channel
+      - description: SHA Engine TX DMA Channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx1
+      - const: tx2
+
+required:
+  - compatible
+  - reg
+  - dmas
+  - dma-names
+
+additionalProperties: false
+
+examples:
+  - |
+    crypto@40800000 {
+        compatible = "ti,am62l-dthev2";
+        reg = <0x40800000 0x10000>;
+
+        dmas = <&main_bcdma 0 0 0x4700 0>,
+               <&main_bcdma 0 0 0xc701 0>,
+               <&main_bcdma 0 0 0xc700 0>;
+        dma-names = "rx", "tx1", "tx2";
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index fe168477caa4..0f5bb8ad7653 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -25169,6 +25169,12 @@ S:	Odd Fixes
 F:	drivers/clk/ti/
 F:	include/linux/clk/ti.h
 
+TI DATA TRANSFORM AND HASHING ENGINE (DTHE) V2 CRYPTO DRIVER
+M:	T Pratham <t-pratham@ti.com>
+L:	linux-crypto@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml
+
 TI DAVINCI MACHINE SUPPORT
 M:	Bartosz Golaszewski <brgl@bgdev.pl>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.43.0

[PATCH v7 2/2] crypto: ti: Add driver for DTHE V2 AES Engine (ECB, CBC)

[T Pratham]

Add support for ECB and CBC modes in the AES Engine of the DTHE V2
hardware cryptography engine.

Signed-off-by: T Pratham <t-pratham@ti.com>
---
 MAINTAINERS                       |   1 +
 drivers/crypto/Kconfig            |   1 +
 drivers/crypto/Makefile           |   1 +
 drivers/crypto/ti/Kconfig         |  14 +
 drivers/crypto/ti/Makefile        |   3 +
 drivers/crypto/ti/dthev2-aes.c    | 411 ++++++++++++++++++++++++++++++
 drivers/crypto/ti/dthev2-common.c | 217 ++++++++++++++++
 drivers/crypto/ti/dthev2-common.h | 101 ++++++++
 8 files changed, 749 insertions(+)
 create mode 100644 drivers/crypto/ti/Kconfig
 create mode 100644 drivers/crypto/ti/Makefile
 create mode 100644 drivers/crypto/ti/dthev2-aes.c
 create mode 100644 drivers/crypto/ti/dthev2-common.c
 create mode 100644 drivers/crypto/ti/dthev2-common.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 0f5bb8ad7653..ca728cc24169 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -25174,6 +25174,7 @@ M:	T Pratham <t-pratham@ti.com>
 L:	linux-crypto@vger.kernel.org
 S:	Supported
 F:	Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml
+F:	drivers/crypto/ti/
 
 TI DAVINCI MACHINE SUPPORT
 M:	Bartosz Golaszewski <brgl@bgdev.pl>
diff --git a/drivers/crypto/Kconfig b/drivers/crypto/Kconfig
index 04b4c43b6bae..f056ec58c96e 100644
--- a/drivers/crypto/Kconfig
+++ b/drivers/crypto/Kconfig
@@ -863,5 +863,6 @@ config CRYPTO_DEV_SA2UL
 source "drivers/crypto/aspeed/Kconfig"
 source "drivers/crypto/starfive/Kconfig"
 source "drivers/crypto/inside-secure/eip93/Kconfig"
+source "drivers/crypto/ti/Kconfig"
 
 endif # CRYPTO_HW
diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile
index 22eadcc8f4a2..c0e8d4acc37c 100644
--- a/drivers/crypto/Makefile
+++ b/drivers/crypto/Makefile
@@ -48,3 +48,4 @@ obj-$(CONFIG_CRYPTO_DEV_AMLOGIC_GXL) += amlogic/
 obj-y += intel/
 obj-y += starfive/
 obj-y += cavium/
+obj-$(CONFIG_ARCH_K3) += ti/
diff --git a/drivers/crypto/ti/Kconfig b/drivers/crypto/ti/Kconfig
new file mode 100644
index 000000000000..38d22cab05a9
--- /dev/null
+++ b/drivers/crypto/ti/Kconfig
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config CRYPTO_DEV_TI_DTHEV2
+	tristate "Support for TI DTHE V2 cryptography engine"
+	depends on CRYPTO && CRYPTO_HW && ARCH_K3
+	select CRYPTO_ENGINE
+	select CRYPTO_SKCIPHER
+	select CRYPTO_ECB
+	select CRYPTO_CBC
+	help
+	  This enables support for the TI DTHE V2 hw cryptography engine
+	  which can be found on TI K3 SOCs. Selecting this enables use
+	  of hardware offloading for cryptographic algorithms on
+	  these devices, providing enhanced resistance against side-channel
+	  attacks.
diff --git a/drivers/crypto/ti/Makefile b/drivers/crypto/ti/Makefile
new file mode 100644
index 000000000000..b883078f203d
--- /dev/null
+++ b/drivers/crypto/ti/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_CRYPTO_DEV_TI_DTHEV2) += dthev2.o
+dthev2-objs := dthev2-common.o dthev2-aes.o
diff --git a/drivers/crypto/ti/dthev2-aes.c b/drivers/crypto/ti/dthev2-aes.c
new file mode 100644
index 000000000000..0431a36d8c4a
--- /dev/null
+++ b/drivers/crypto/ti/dthev2-aes.c
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * K3 DTHE V2 crypto accelerator driver
+ *
+ * Copyright (C) Texas Instruments 2025 - https://www.ti.com
+ * Author: T Pratham <t-pratham@ti.com>
+ */
+
+#include <crypto/aead.h>
+#include <crypto/aes.h>
+#include <crypto/algapi.h>
+#include <crypto/engine.h>
+#include <crypto/internal/aead.h>
+#include <crypto/internal/skcipher.h>
+
+#include "dthev2-common.h"
+
+#include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+#include <linux/scatterlist.h>
+
+/* Registers */
+
+// AES Engine
+#define DTHE_P_AES_BASE		0x7000
+#define DTHE_P_AES_KEY1_0	0x0038
+#define DTHE_P_AES_KEY1_1	0x003C
+#define DTHE_P_AES_KEY1_2	0x0030
+#define DTHE_P_AES_KEY1_3	0x0034
+#define DTHE_P_AES_KEY1_4	0x0028
+#define DTHE_P_AES_KEY1_5	0x002C
+#define DTHE_P_AES_KEY1_6	0x0020
+#define DTHE_P_AES_KEY1_7	0x0024
+#define DTHE_P_AES_IV_IN_0	0x0040
+#define DTHE_P_AES_IV_IN_1	0x0044
+#define DTHE_P_AES_IV_IN_2	0x0048
+#define DTHE_P_AES_IV_IN_3	0x004C
+#define DTHE_P_AES_CTRL		0x0050
+#define DTHE_P_AES_C_LENGTH_0	0x0054
+#define DTHE_P_AES_C_LENGTH_1	0x0058
+#define DTHE_P_AES_AUTH_LENGTH	0x005C
+#define DTHE_P_AES_DATA_IN_OUT	0x0060
+
+#define DTHE_P_AES_SYSCONFIG	0x0084
+#define DTHE_P_AES_IRQSTATUS	0x008C
+#define DTHE_P_AES_IRQENABLE	0x0090
+
+/* Register write values and macros */
+
+enum aes_ctrl_mode_masks {
+	AES_CTRL_ECB_MASK = 0x00,
+	AES_CTRL_CBC_MASK = BIT(5),
+};
+
+#define DTHE_AES_CTRL_MODE_CLEAR_MASK		~GENMASK(28, 5)
+
+#define DTHE_AES_CTRL_DIR_ENC			BIT(2)
+
+#define DTHE_AES_CTRL_KEYSIZE_16B		BIT(3)
+#define DTHE_AES_CTRL_KEYSIZE_24B		BIT(4)
+#define DTHE_AES_CTRL_KEYSIZE_32B		(BIT(3) | BIT(4))
+
+#define DTHE_AES_CTRL_SAVE_CTX_SET		BIT(29)
+
+#define DTHE_AES_CTRL_OUTPUT_READY		BIT_MASK(0)
+#define DTHE_AES_CTRL_INPUT_READY		BIT_MASK(1)
+#define DTHE_AES_CTRL_SAVED_CTX_READY		BIT_MASK(30)
+#define DTHE_AES_CTRL_CTX_READY			BIT_MASK(31)
+
+#define DTHE_AES_SYSCONFIG_DMA_DATA_IN_OUT_EN	GENMASK(6, 5)
+#define DTHE_AES_IRQENABLE_EN_ALL		GENMASK(3, 0)
+
+/* Misc */
+#define AES_IV_SIZE				AES_BLOCK_SIZE
+#define AES_BLOCK_WORDS				(AES_BLOCK_SIZE / sizeof(u32))
+#define AES_IV_WORDS				AES_BLOCK_WORDS
+
+static int dthe_cipher_init_tfm(struct crypto_skcipher *tfm)
+{
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct dthe_data *dev_data = dthe_get_dev(ctx);
+
+	ctx->dev_data = dev_data;
+	ctx->keylen = 0;
+
+	return 0;
+}
+
+static int dthe_aes_setkey(struct crypto_skcipher *tfm, const u8 *key, unsigned int keylen)
+{
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	if (keylen != AES_KEYSIZE_128 && keylen != AES_KEYSIZE_192 && keylen != AES_KEYSIZE_256)
+		return -EINVAL;
+
+	ctx->keylen = keylen;
+	memcpy(ctx->key, key, keylen);
+
+	return 0;
+}
+
+static int dthe_aes_ecb_setkey(struct crypto_skcipher *tfm, const u8 *key, unsigned int keylen)
+{
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	ctx->aes_mode = DTHE_AES_ECB;
+
+	return dthe_aes_setkey(tfm, key, keylen);
+}
+
+static int dthe_aes_cbc_setkey(struct crypto_skcipher *tfm, const u8 *key, unsigned int keylen)
+{
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	ctx->aes_mode = DTHE_AES_CBC;
+
+	return dthe_aes_setkey(tfm, key, keylen);
+}
+
+static void dthe_aes_set_ctrl_key(struct dthe_tfm_ctx *ctx,
+				  struct dthe_aes_req_ctx *rctx,
+				  u32 *iv_in)
+{
+	struct dthe_data *dev_data = dthe_get_dev(ctx);
+	void __iomem *aes_base_reg = dev_data->regs + DTHE_P_AES_BASE;
+	u32 ctrl_val = 0;
+
+	writel_relaxed(ctx->key[0], aes_base_reg + DTHE_P_AES_KEY1_0);
+	writel_relaxed(ctx->key[1], aes_base_reg + DTHE_P_AES_KEY1_1);
+	writel_relaxed(ctx->key[2], aes_base_reg + DTHE_P_AES_KEY1_2);
+	writel_relaxed(ctx->key[3], aes_base_reg + DTHE_P_AES_KEY1_3);
+
+	if (ctx->keylen > AES_KEYSIZE_128) {
+		writel_relaxed(ctx->key[4], aes_base_reg + DTHE_P_AES_KEY1_4);
+		writel_relaxed(ctx->key[5], aes_base_reg + DTHE_P_AES_KEY1_5);
+	}
+	if (ctx->keylen == AES_KEYSIZE_256) {
+		writel_relaxed(ctx->key[6], aes_base_reg + DTHE_P_AES_KEY1_6);
+		writel_relaxed(ctx->key[7], aes_base_reg + DTHE_P_AES_KEY1_7);
+	}
+
+	if (rctx->enc)
+		ctrl_val |= DTHE_AES_CTRL_DIR_ENC;
+
+	if (ctx->keylen == AES_KEYSIZE_128)
+		ctrl_val |= DTHE_AES_CTRL_KEYSIZE_16B;
+	else if (ctx->keylen == AES_KEYSIZE_192)
+		ctrl_val |= DTHE_AES_CTRL_KEYSIZE_24B;
+	else
+		ctrl_val |= DTHE_AES_CTRL_KEYSIZE_32B;
+
+	// Write AES mode
+	ctrl_val &= DTHE_AES_CTRL_MODE_CLEAR_MASK;
+	switch (ctx->aes_mode) {
+	case DTHE_AES_ECB:
+		ctrl_val |= AES_CTRL_ECB_MASK;
+		break;
+	case DTHE_AES_CBC:
+		ctrl_val |= AES_CTRL_CBC_MASK;
+		break;
+	}
+
+	if (iv_in) {
+		ctrl_val |= DTHE_AES_CTRL_SAVE_CTX_SET;
+		for (int i = 0; i < AES_IV_WORDS; ++i)
+			writel_relaxed(iv_in[i],
+				       aes_base_reg + DTHE_P_AES_IV_IN_0 + (DTHE_REG_SIZE * i));
+	}
+
+	writel_relaxed(ctrl_val, aes_base_reg + DTHE_P_AES_CTRL);
+}
+
+static void dthe_aes_dma_in_callback(void *data)
+{
+	struct skcipher_request *req = (struct skcipher_request *)data;
+	struct dthe_aes_req_ctx *rctx = skcipher_request_ctx(req);
+
+	complete(&rctx->aes_compl);
+}
+
+static int dthe_aes_run(struct crypto_engine *engine, void *areq)
+{
+	struct skcipher_request *req = container_of(areq, struct skcipher_request, base);
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(crypto_skcipher_reqtfm(req));
+	struct dthe_data *dev_data = dthe_get_dev(ctx);
+	struct dthe_aes_req_ctx *rctx = skcipher_request_ctx(req);
+
+	unsigned int len = req->cryptlen;
+	struct scatterlist *src = req->src;
+	struct scatterlist *dst = req->dst;
+
+	int src_nents = sg_nents_for_len(src, len);
+	int dst_nents;
+
+	int src_mapped_nents;
+	int dst_mapped_nents;
+
+	bool diff_dst;
+	enum dma_data_direction src_dir, dst_dir;
+
+	struct device *tx_dev, *rx_dev;
+	struct dma_async_tx_descriptor *desc_in, *desc_out;
+
+	int ret;
+
+	void __iomem *aes_base_reg = dev_data->regs + DTHE_P_AES_BASE;
+
+	u32 aes_irqenable_val = readl_relaxed(aes_base_reg + DTHE_P_AES_IRQENABLE);
+	u32 aes_sysconfig_val = readl_relaxed(aes_base_reg + DTHE_P_AES_SYSCONFIG);
+
+	aes_sysconfig_val |= DTHE_AES_SYSCONFIG_DMA_DATA_IN_OUT_EN;
+	writel_relaxed(aes_sysconfig_val, aes_base_reg + DTHE_P_AES_SYSCONFIG);
+
+	aes_irqenable_val |= DTHE_AES_IRQENABLE_EN_ALL;
+	writel_relaxed(aes_irqenable_val, aes_base_reg + DTHE_P_AES_IRQENABLE);
+
+	if (src == dst) {
+		diff_dst = false;
+		src_dir = DMA_BIDIRECTIONAL;
+		dst_dir = DMA_BIDIRECTIONAL;
+	} else {
+		diff_dst = true;
+		src_dir = DMA_TO_DEVICE;
+		dst_dir  = DMA_FROM_DEVICE;
+	}
+
+	tx_dev = dmaengine_get_dma_device(dev_data->dma_aes_tx);
+	rx_dev = dmaengine_get_dma_device(dev_data->dma_aes_rx);
+
+	src_mapped_nents = dma_map_sg(tx_dev, src, src_nents, src_dir);
+	if (src_mapped_nents == 0) {
+		ret = -EINVAL;
+		goto aes_err;
+	}
+
+	if (!diff_dst) {
+		dst_nents = src_nents;
+		dst_mapped_nents = src_mapped_nents;
+	} else {
+		dst_nents = sg_nents_for_len(dst, len);
+		dst_mapped_nents = dma_map_sg(rx_dev, dst, dst_nents, dst_dir);
+		if (dst_mapped_nents == 0) {
+			dma_unmap_sg(tx_dev, src, src_nents, src_dir);
+			ret = -EINVAL;
+			goto aes_err;
+		}
+	}
+
+	desc_in = dmaengine_prep_slave_sg(dev_data->dma_aes_rx, dst, dst_mapped_nents,
+					  DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!desc_in) {
+		dev_err(dev_data->dev, "IN prep_slave_sg() failed\n");
+		ret = -EINVAL;
+		goto aes_prep_err;
+	}
+
+	desc_out = dmaengine_prep_slave_sg(dev_data->dma_aes_tx, src, src_mapped_nents,
+					   DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!desc_out) {
+		dev_err(dev_data->dev, "OUT prep_slave_sg() failed\n");
+		ret = -EINVAL;
+		goto aes_prep_err;
+	}
+
+	desc_in->callback = dthe_aes_dma_in_callback;
+	desc_in->callback_param = req;
+
+	init_completion(&rctx->aes_compl);
+
+	if (ctx->aes_mode == DTHE_AES_ECB)
+		dthe_aes_set_ctrl_key(ctx, rctx, NULL);
+	else
+		dthe_aes_set_ctrl_key(ctx, rctx, (u32 *)req->iv);
+
+	writel_relaxed(lower_32_bits(req->cryptlen), aes_base_reg + DTHE_P_AES_C_LENGTH_0);
+	writel_relaxed(upper_32_bits(req->cryptlen), aes_base_reg + DTHE_P_AES_C_LENGTH_1);
+
+	dmaengine_submit(desc_in);
+	dmaengine_submit(desc_out);
+
+	dma_async_issue_pending(dev_data->dma_aes_rx);
+	dma_async_issue_pending(dev_data->dma_aes_tx);
+
+	// Need to do a timeout to ensure finalise gets called if DMA callback fails for any reason
+	ret = wait_for_completion_timeout(&rctx->aes_compl, msecs_to_jiffies(DTHE_DMA_TIMEOUT_MS));
+	if (!ret) {
+		ret = -ETIMEDOUT;
+		dmaengine_terminate_sync(dev_data->dma_aes_rx);
+		dmaengine_terminate_sync(dev_data->dma_aes_tx);
+
+		for (int i = 0; i < AES_BLOCK_WORDS; ++i)
+			readl_relaxed(aes_base_reg + DTHE_P_AES_DATA_IN_OUT + (DTHE_REG_SIZE * i));
+	} else {
+		ret = 0;
+	}
+
+	// For modes other than ECB, read IV_OUT
+	if (ctx->aes_mode != DTHE_AES_ECB) {
+		u32 *iv_out = (u32 *)req->iv;
+
+		for (int i = 0; i < AES_IV_WORDS; ++i)
+			iv_out[i] = readl_relaxed(aes_base_reg +
+						  DTHE_P_AES_IV_IN_0 +
+						  (DTHE_REG_SIZE * i));
+	}
+
+aes_prep_err:
+	dma_unmap_sg(tx_dev, src, src_nents, src_dir);
+	if (dst_dir != DMA_BIDIRECTIONAL)
+		dma_unmap_sg(rx_dev, dst, dst_nents, dst_dir);
+
+aes_err:
+	local_bh_disable();
+	crypto_finalize_skcipher_request(dev_data->engine, req, ret);
+	local_bh_enable();
+	return ret;
+}
+
+static int dthe_aes_crypt(struct skcipher_request *req)
+{
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(crypto_skcipher_reqtfm(req));
+	struct dthe_data *dev_data = dthe_get_dev(ctx);
+	struct crypto_engine *engine;
+
+	/*
+	 * If data is not a multiple of AES_BLOCK_SIZE, need to return -EINVAL
+	 * If data length input is zero, no need to do any operation.
+	 */
+	if (req->cryptlen % AES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
+	engine = dev_data->engine;
+	return crypto_transfer_skcipher_request_to_engine(engine, req);
+}
+
+static int dthe_aes_encrypt(struct skcipher_request *req)
+{
+	struct dthe_aes_req_ctx *rctx = skcipher_request_ctx(req);
+
+	rctx->enc = 1;
+	return dthe_aes_crypt(req);
+}
+
+static int dthe_aes_decrypt(struct skcipher_request *req)
+{
+	struct dthe_aes_req_ctx *rctx = skcipher_request_ctx(req);
+
+	rctx->enc = 0;
+	return dthe_aes_crypt(req);
+}
+
+static struct skcipher_engine_alg cipher_algs[] = {
+	{
+		.base.init			= dthe_cipher_init_tfm,
+		.base.setkey			= dthe_aes_ecb_setkey,
+		.base.encrypt			= dthe_aes_encrypt,
+		.base.decrypt			= dthe_aes_decrypt,
+		.base.min_keysize		= AES_MIN_KEY_SIZE,
+		.base.max_keysize		= AES_MAX_KEY_SIZE,
+		.base.base = {
+			.cra_name		= "ecb(aes)",
+			.cra_driver_name	= "ecb-aes-dthev2",
+			.cra_priority		= 299,
+			.cra_flags		= CRYPTO_ALG_TYPE_SKCIPHER |
+						  CRYPTO_ALG_KERN_DRIVER_ONLY,
+			.cra_alignmask		= AES_BLOCK_SIZE - 1,
+			.cra_blocksize		= AES_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct dthe_tfm_ctx),
+			.cra_reqsize		= sizeof(struct dthe_aes_req_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.op.do_one_request = dthe_aes_run,
+	}, /* ECB AES */
+	{
+		.base.init			= dthe_cipher_init_tfm,
+		.base.setkey			= dthe_aes_cbc_setkey,
+		.base.encrypt			= dthe_aes_encrypt,
+		.base.decrypt			= dthe_aes_decrypt,
+		.base.min_keysize		= AES_MIN_KEY_SIZE,
+		.base.max_keysize		= AES_MAX_KEY_SIZE,
+		.base.ivsize			= AES_IV_SIZE,
+		.base.base = {
+			.cra_name		= "cbc(aes)",
+			.cra_driver_name	= "cbc-aes-dthev2",
+			.cra_priority		= 299,
+			.cra_flags		= CRYPTO_ALG_TYPE_SKCIPHER |
+						  CRYPTO_ALG_KERN_DRIVER_ONLY,
+			.cra_alignmask		= AES_BLOCK_SIZE - 1,
+			.cra_blocksize		= AES_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct dthe_tfm_ctx),
+			.cra_reqsize		= sizeof(struct dthe_aes_req_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.op.do_one_request = dthe_aes_run,
+	} /* CBC AES */
+};
+
+int dthe_register_aes_algs(void)
+{
+	return crypto_engine_register_skciphers(cipher_algs, ARRAY_SIZE(cipher_algs));
+}
+
+void dthe_unregister_aes_algs(void)
+{
+	crypto_engine_unregister_skciphers(cipher_algs, ARRAY_SIZE(cipher_algs));
+}
diff --git a/drivers/crypto/ti/dthev2-common.c b/drivers/crypto/ti/dthev2-common.c
new file mode 100644
index 000000000000..c39d37933b9e
--- /dev/null
+++ b/drivers/crypto/ti/dthev2-common.c
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * K3 DTHE V2 crypto accelerator driver
+ *
+ * Copyright (C) Texas Instruments 2025 - https://www.ti.com
+ * Author: T Pratham <t-pratham@ti.com>
+ */
+
+#include <crypto/aes.h>
+#include <crypto/algapi.h>
+#include <crypto/engine.h>
+#include <crypto/internal/aead.h>
+#include <crypto/internal/skcipher.h>
+
+#include "dthev2-common.h"
+
+#include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/dmapool.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/scatterlist.h>
+
+#define DRIVER_NAME	"dthev2"
+
+static struct dthe_list dthe_dev_list = {
+	.dev_list = LIST_HEAD_INIT(dthe_dev_list.dev_list),
+	.lock = __SPIN_LOCK_UNLOCKED(dthe_dev_list.lock),
+};
+
+struct dthe_data *dthe_get_dev(struct dthe_tfm_ctx *ctx)
+{
+	struct dthe_data *dev_data;
+
+	if (ctx->dev_data)
+		return ctx->dev_data;
+
+	spin_lock_bh(&dthe_dev_list.lock);
+	dev_data = list_first_entry(&dthe_dev_list.dev_list, struct dthe_data, list);
+	if (dev_data)
+		list_move_tail(&dev_data->list, &dthe_dev_list.dev_list);
+	spin_unlock_bh(&dthe_dev_list.lock);
+
+	return dev_data;
+}
+
+static int dthe_dma_init(struct dthe_data *dev_data)
+{
+	int ret;
+	struct dma_slave_config cfg;
+
+	dev_data->dma_aes_rx = NULL;
+	dev_data->dma_aes_tx = NULL;
+	dev_data->dma_sha_tx = NULL;
+
+	dev_data->dma_aes_rx = dma_request_chan(dev_data->dev, "rx");
+	if (IS_ERR(dev_data->dma_aes_rx)) {
+		return dev_err_probe(dev_data->dev, PTR_ERR(dev_data->dma_aes_rx),
+				     "Unable to request rx DMA channel\n");
+	}
+
+	dev_data->dma_aes_tx = dma_request_chan(dev_data->dev, "tx1");
+	if (IS_ERR(dev_data->dma_aes_tx)) {
+		ret = dev_err_probe(dev_data->dev, PTR_ERR(dev_data->dma_aes_tx),
+				    "Unable to request tx1 DMA channel\n");
+		goto err_dma_aes_tx;
+	}
+
+	dev_data->dma_sha_tx = dma_request_chan(dev_data->dev, "tx2");
+	if (IS_ERR(dev_data->dma_sha_tx)) {
+		ret = dev_err_probe(dev_data->dev, PTR_ERR(dev_data->dma_sha_tx),
+				    "Unable to request tx2 DMA channel\n");
+		goto err_dma_sha_tx;
+	}
+
+	memzero_explicit(&cfg, sizeof(cfg));
+
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	cfg.src_maxburst = 4;
+
+	ret = dmaengine_slave_config(dev_data->dma_aes_rx, &cfg);
+	if (ret) {
+		dev_err(dev_data->dev, "Can't configure IN dmaengine slave: %d\n", ret);
+		goto err_dma_config;
+	}
+
+	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	cfg.dst_maxburst = 4;
+
+	ret = dmaengine_slave_config(dev_data->dma_aes_tx, &cfg);
+	if (ret) {
+		dev_err(dev_data->dev, "Can't configure OUT dmaengine slave: %d\n", ret);
+		goto err_dma_config;
+	}
+
+	return 0;
+
+err_dma_config:
+	dma_release_channel(dev_data->dma_sha_tx);
+err_dma_sha_tx:
+	dma_release_channel(dev_data->dma_aes_tx);
+err_dma_aes_tx:
+	dma_release_channel(dev_data->dma_aes_rx);
+
+	return ret;
+}
+
+static int dthe_register_algs(void)
+{
+	return dthe_register_aes_algs();
+}
+
+static void dthe_unregister_algs(void)
+{
+	dthe_unregister_aes_algs();
+}
+
+static int dthe_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct dthe_data *dev_data;
+	int ret;
+
+	dev_data = devm_kzalloc(dev, sizeof(*dev_data), GFP_KERNEL);
+	if (!dev_data)
+		return -ENOMEM;
+
+	dev_data->dev = dev;
+	dev_data->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(dev_data->regs))
+		return PTR_ERR(dev_data->regs);
+
+	platform_set_drvdata(pdev, dev_data);
+
+	spin_lock(&dthe_dev_list.lock);
+	list_add(&dev_data->list, &dthe_dev_list.dev_list);
+	spin_unlock(&dthe_dev_list.lock);
+
+	ret = dthe_dma_init(dev_data);
+	if (ret)
+		goto probe_dma_err;
+
+	dev_data->engine = crypto_engine_alloc_init(dev, 1);
+	if (!dev_data->engine) {
+		ret = -ENOMEM;
+		goto probe_engine_err;
+	}
+
+	ret = crypto_engine_start(dev_data->engine);
+	if (ret) {
+		dev_err(dev, "Failed to start crypto engine\n");
+		goto probe_engine_start_err;
+	}
+
+	ret = dthe_register_algs();
+	if (ret) {
+		dev_err(dev, "Failed to register algs\n");
+		goto probe_engine_start_err;
+	}
+
+	return 0;
+
+probe_engine_start_err:
+	crypto_engine_exit(dev_data->engine);
+probe_engine_err:
+	dma_release_channel(dev_data->dma_aes_rx);
+	dma_release_channel(dev_data->dma_aes_tx);
+	dma_release_channel(dev_data->dma_sha_tx);
+probe_dma_err:
+	spin_lock(&dthe_dev_list.lock);
+	list_del(&dev_data->list);
+	spin_unlock(&dthe_dev_list.lock);
+
+	return ret;
+}
+
+static void dthe_remove(struct platform_device *pdev)
+{
+	struct dthe_data *dev_data = platform_get_drvdata(pdev);
+
+	spin_lock(&dthe_dev_list.lock);
+	list_del(&dev_data->list);
+	spin_unlock(&dthe_dev_list.lock);
+
+	dthe_unregister_algs();
+
+	crypto_engine_exit(dev_data->engine);
+
+	dma_release_channel(dev_data->dma_aes_rx);
+	dma_release_channel(dev_data->dma_aes_tx);
+	dma_release_channel(dev_data->dma_sha_tx);
+}
+
+static const struct of_device_id dthe_of_match[] = {
+	{ .compatible = "ti,am62l-dthev2", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, dthe_of_match);
+
+static struct platform_driver dthe_driver = {
+	.probe	= dthe_probe,
+	.remove	= dthe_remove,
+	.driver = {
+		.name		= DRIVER_NAME,
+		.of_match_table	= dthe_of_match,
+	},
+};
+
+module_platform_driver(dthe_driver);
+
+MODULE_AUTHOR("T Pratham <t-pratham@ti.com>");
+MODULE_DESCRIPTION("Texas Instruments DTHE V2 driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/crypto/ti/dthev2-common.h b/drivers/crypto/ti/dthev2-common.h
new file mode 100644
index 000000000000..68c94acda8aa
--- /dev/null
+++ b/drivers/crypto/ti/dthev2-common.h
@@ -0,0 +1,101 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * K3 DTHE V2 crypto accelerator driver
+ *
+ * Copyright (C) Texas Instruments 2025 - https://www.ti.com
+ * Author: T Pratham <t-pratham@ti.com>
+ */
+
+#ifndef __TI_DTHEV2_H__
+#define __TI_DTHEV2_H__
+
+#include <crypto/aead.h>
+#include <crypto/aes.h>
+#include <crypto/algapi.h>
+#include <crypto/engine.h>
+#include <crypto/hash.h>
+#include <crypto/internal/aead.h>
+#include <crypto/internal/hash.h>
+#include <crypto/internal/skcipher.h>
+
+#include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/dmapool.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+#include <linux/scatterlist.h>
+
+#define DTHE_REG_SIZE		4
+#define DTHE_DMA_TIMEOUT_MS	2000
+
+enum dthe_aes_mode {
+	DTHE_AES_ECB = 0,
+	DTHE_AES_CBC,
+};
+
+/* Driver specific struct definitions */
+
+/**
+ * struct dthe_data - DTHE_V2 driver instance data
+ * @dev: Device pointer
+ * @regs: Base address of the register space
+ * @list: list node for dev
+ * @engine: Crypto engine instance
+ * @dma_aes_rx: AES Rx DMA Channel
+ * @dma_aes_tx: AES Tx DMA Channel
+ * @dma_sha_tx: SHA Tx DMA Channel
+ */
+struct dthe_data {
+	struct device *dev;
+	void __iomem *regs;
+	struct list_head list;
+	struct crypto_engine *engine;
+
+	struct dma_chan *dma_aes_rx;
+	struct dma_chan *dma_aes_tx;
+
+	struct dma_chan *dma_sha_tx;
+};
+
+/**
+ * struct dthe_list - device data list head
+ * @dev_list: linked list head
+ * @lock: Spinlock protecting accesses to the list
+ */
+struct dthe_list {
+	struct list_head dev_list;
+	spinlock_t lock;
+};
+
+/**
+ * struct dthe_tfm_ctx - Transform ctx struct containing ctx for all sub-components of DTHE V2
+ * @dev_data: Device data struct pointer
+ * @keylen: AES key length
+ * @key: AES key
+ * @aes_mode: AES mode
+ */
+struct dthe_tfm_ctx {
+	struct dthe_data *dev_data;
+	unsigned int keylen;
+	u32 key[AES_KEYSIZE_256 / sizeof(u32)];
+	enum dthe_aes_mode aes_mode;
+};
+
+/**
+ * struct dthe_aes_req_ctx - AES engine req ctx struct
+ * @enc: flag indicating encryption or decryption operation
+ * @aes_compl: Completion variable for use in manual completion in case of DMA callback failure
+ */
+struct dthe_aes_req_ctx {
+	int enc;
+	struct completion aes_compl;
+};
+
+/* Struct definitions end */
+
+struct dthe_data *dthe_get_dev(struct dthe_tfm_ctx *ctx);
+
+int dthe_register_aes_algs(void);
+void dthe_unregister_aes_algs(void);
+
+#endif
-- 
2.43.0

Re: [PATCH v7 0/2] Add support for Texas Instruments DTHEv2 Crypto Engine

[Herbert Xu]

On Wed, Aug 20, 2025 at 02:42:25PM +0530, T Pratham wrote:
> Data Transform and Hashing Engine (DTHE) v2 is a new cryptography engine
> introduced i TI AM62L SoC. DTHEv2 consists of multiple crypto IPs[1] (such
> as AES Engine, hashing engine, TRNG, etc.) which can be used for
> offloading cryptographic operations off of the CPU. The primary benefit
> of DTHEv2 is enhanced side-channel attack resistance, with AES and PKE
> engine being DPA and EMA resistant. These side-channel resistances are
> the underlying requirement for various certifications like SESIP, PSA,
> and IEC62443 (lvl 3+). Thus, DTHEv2 provides critical security benefits
> for embedded systems that require protection against passive physical
> attacks.
> 
> The AES Engine of DTHEv2 supports multiple AES modes (ECB, CBC, CTR,
> CFB, f8), several protocols (GCM, CCM, XTS) and authentication modes
> (CBC-MAC and f9). The hashing engine supports MD5, SHA1, and SHA2 (224,
> 256, 384, 512) algorithms along with HMAC. This patch series introduces
> basic driver support for DTHEv2 engine, beginning with suporting AES-ECB
> and AES-CBC algorithms. Other algorithms are planned to be added
> gradually in phases after initial suppport is added.
> 
> The driver is tested using full kernel crypto selftests (CRYPTO_SELFTESTS)
> which all pass successfully [2].
> 
> Signed-off-by: T Pratham <t-pratham@ti.com>
> ---
> [1]: Section 14.6.3 (DMA Control Registers -> DMASS_DTHE)
> Link: https://www.ti.com/lit/ug/sprujb4/sprujb4.pdf
> 
> [2]: DTHEv2 AES-ECB and AES-CBC kernel self-tests logs
> Link: https://gist.github.com/Pratham-T/aaa499cf50d20310cb27266a645bfd60
> 
> Change log:
> v7:
>  - Dropped redundant crypto_engine_stop() calls.
>  - Corrected Reviewed-by tag.
> v6:
>  - Reworded the cover letter and commit messages to name DTHEv2 as a
>    crypto engine instead of crypto accelerator.
>  - Reworded the cover letter completely to emphasise more on the utility
>    of DTHEv2 as better resistance against physical attacks
>  - Reworded DTHEv2 description (help text) in KConfig
>  - Added dma_terminate_sync calls to ensure DMA requests are removed in
>    case when completion times-out.
>  - Some rearrangement of fields between dthe_tfm_ctx and dthe_aes_req_ctx
>    struct, so that per tfm members are correctly placed in tfm_ctx and per
>    request members are in req_ctx. Subsequently setkey, encrypt and
>    decrypt functions are also changed.
>  - Removed exit_tfm function which was useless and not required.
>  - Removed unnecessary zeroing of tfm_ctx object in init_tfm.
>  - Corrected return value in dthe_aes_run function.
>  - Reduced cra_priority of DTHEv2 algorithms.
> v5:
>  - Simplified tfm ctx struct
>  - Set cra_reqsize instead of using crypto_skcipher_set_reqsize()
>  - Move setting sysconfig and irqenable registers to dthe_aes_run
> v4:
>  - Corrected dt-bindings example indentation
>  - Simplified dt-bindings example, removing the node surrounding crypto
>  - Fixed typo in dthev2-common.h header guard
>  - Removed unused ctx field in dev_data struct
>  - Moved per-op data into request context
> v3:
>  - Corrected dt-bindings reg length is too long error
>  - Converted AES driver code to use crypto_engine APIs for using
>    internal crypto queue instead of mutex.
>  - Removed calls to skcipher_request_complete in paths not returning
>    -EINPROGRESS before.
>  - Added missing KConfig import, which was accidentally removed in v2.
> 
> v2:
>  - Corrected dt-bindings syntax errors and other review comments in v1.
>  - Completely changed driver code structure, splitting code into
>    multiple files
> 
> Link to previous versions:
> v6: https://lore.kernel.org/all/20250819065844.3337101-1-t-pratham@ti.com/
> v5: https://lore.kernel.org/all/20250603124217.957116-1-t-pratham@ti.com/
> v4: https://lore.kernel.org/all/20250508101723.846210-2-t-pratham@ti.com/
> v3: https://lore.kernel.org/all/20250502121253.456974-2-t-pratham@ti.com/
> v2: https://lore.kernel.org/all/20250411091321.2925308-1-t-pratham@ti.com/
> v1: https://lore.kernel.org/all/20250206-dthe-v2-aes-v1-0-1e86cf683928@ti.com/
> ---
> 
> T Pratham (2):
>   dt-bindings: crypto: Add binding for TI DTHE V2
>   crypto: ti: Add driver for DTHE V2 AES Engine (ECB, CBC)
> 
>  .../bindings/crypto/ti,am62l-dthev2.yaml      |  50 +++
>  MAINTAINERS                                   |   7 +
>  drivers/crypto/Kconfig                        |   1 +
>  drivers/crypto/Makefile                       |   1 +
>  drivers/crypto/ti/Kconfig                     |  14 +
>  drivers/crypto/ti/Makefile                    |   3 +
>  drivers/crypto/ti/dthev2-aes.c                | 411 ++++++++++++++++++
>  drivers/crypto/ti/dthev2-common.c             | 217 +++++++++
>  drivers/crypto/ti/dthev2-common.h             | 101 +++++
>  9 files changed, 805 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/crypto/ti,am62l-dthev2.yaml
>  create mode 100644 drivers/crypto/ti/Kconfig
>  create mode 100644 drivers/crypto/ti/Makefile
>  create mode 100644 drivers/crypto/ti/dthev2-aes.c
>  create mode 100644 drivers/crypto/ti/dthev2-common.c
>  create mode 100644 drivers/crypto/ti/dthev2-common.h
> 
> -- 
> 2.43.0

All applied.  Thanks.
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

[PATCH] crypto: ti - Enable compile testing for dthev2

[Herbert Xu]

Allow ti dthev2 driver to be compile-tested.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile
index c0e8d4acc37c..170e10b18f9b 100644
--- a/drivers/crypto/Makefile
+++ b/drivers/crypto/Makefile
@@ -48,4 +48,4 @@ obj-$(CONFIG_CRYPTO_DEV_AMLOGIC_GXL) += amlogic/
 obj-y += intel/
 obj-y += starfive/
 obj-y += cavium/
-obj-$(CONFIG_ARCH_K3) += ti/
+obj-y += ti/
diff --git a/drivers/crypto/ti/Kconfig b/drivers/crypto/ti/Kconfig
index 38d22cab05a9..d4f91c1e0cb5 100644
--- a/drivers/crypto/ti/Kconfig
+++ b/drivers/crypto/ti/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config CRYPTO_DEV_TI_DTHEV2
 	tristate "Support for TI DTHE V2 cryptography engine"
-	depends on CRYPTO && CRYPTO_HW && ARCH_K3
+	depends on ARCH_K3 || COMPILE_TEST
 	select CRYPTO_ENGINE
 	select CRYPTO_SKCIPHER
 	select CRYPTO_ECB
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

Re: [PATCH] crypto: ti - Enable compile testing for dthev2

[T Pratham]

On 30/08/25 14:22, Herbert Xu wrote:
> Allow ti dthev2 driver to be compile-tested.
> 
> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
> 

Acked-by: T Pratham <t-pratham@ti.com>

-- 
Regards
T Pratham <t-pratham@ti.com>