[PATCH v12 0/3] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[PATCH v12 0/3] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[Jens Glathe via B4 Relay]

Device tree for the Lenovo Thinkbook 16 G7 QOY

The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].

Supported features:

- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera
- X1-45 GPU

Not supported yet:

- HDMI port.
- EC and some fn hotkeys.

Limited support yet:

- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.

Notes:

- Putting the camera behind usb_2_dwc3 results in the camera switched off after 30
seconds. With the stand-alone node as previously defined it stays usable and
suspends, as intended. Since the sole reason for the USB camera to be in the
devicetree is the required extra supply (which is guessed, as mentioned), and
its handling by power management, I would propose to keep it this way.

- The gpi_dma nodes appear to be implicitly enabled when a serial device is used.
I added them, no change in behaviour, though. Since this would be the only X1
device adding them afaik, I left them out.

- The cma-memory is removed, it is not on all x1 devices as I assumed.
Haven't found a case where it is required.

- i2c2 defines the keyboard and 4 different touchpad interfaces. With the bundling
of the pinctrl it seems to work better. I've had issues with only clock and touchpad
pinctrl on the i2c2 node, and not keyboard.

This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1 device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).

I have brought up the Thinkbook over the last 7 months since the x1p42100-crd
patches were available. The laptop is very usable now, and quite solid as a dev/
test platform.

Big thanks to Aleksandrs Vinarskis for helping (and sort of persisting) on the
fingerprint, camera and HDMI issues.

[1]: https://psref.lenovo.com/syspool/Sys/PDF/ThinkBook/ThinkBook_16_G7_QOY/ThinkBook_16_G7_QOY_Spec.pdf

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
Changes in v12:
- rebased onto next-20250821
- corrected DMIC supplies in the spirit of [3]
- added missing pinctrl for eDP HPD in the spirit of [4]
- Link to v11: https://lore.kernel.org/r/20250812-tb16-dt-v11-0-4923d2cd7121@oldschoolsolutions.biz

Changes in v11:
- respin due to b4 / git issue (thanks Konrad)
- corrected SoB for patch #3 (thanks Krzysztof)
- Link to v10: https://lore.kernel.org/r/20250810-tb16-dt-v10-0-0bfed6d75c69@oldschoolsolutions.biz

Changes in v10:
- rebased as recommended onto 20250701183625.1968246-1-alex.vinarskis@gmail.com and
  20250724-move-edp-endpoints-v1-3-6ca569812838@oss.qualcomm.com (whole series)
- rebased onto next-20250808
- amended node order
- checked occurrence of touchpad variants: current users have eiher @2c (like mine) or @38
- removed 4 lanes definition from mdss_dp0_out and mdss_dp_1_out. The required patches for
  it are not yet upstream, as it seems.
- removed UFS reset from reserved ranges
- removed commented-out lines 
- Link to v9: https://lore.kernel.org/r/20250701-tb16-dt-v9-0-7d9e280837b5@oldschoolsolutions.biz

Changes in v9:
- rebase to next-20250701
- fix errors listed from Rob Herrings dts check script - one typo, one missing 
  pmic-glink compatible string
- Link to v8: https://lore.kernel.org/r/20250630-tb16-dt-v8-0-cf42a396e736@oldschoolsolutions.biz

Changes in v8:
- rebase to next-20250630
- fix bleed-over of edp0_hpd_active - not in linux-next yet
- fix bleed-over of hdmi definition 
- Link to v7: https://lore.kernel.org/r/20250629-tb16-dt-v7-0-35276341338f@oldschoolsolutions.biz

Changes in v7:
- amended pinctrl order and indents where needed
- interchanged enable-gpios and select-gpios for usb-sbu-mux as they are
  defined in the dsdt - dp altmode function confirmed in both orientations
- picked up reviewed-by and acked-by from Dmitry Baryshkob and Rob Herring
- Link to v6: https://lore.kernel.org/r/20250607-tb16-dt-v6-0-61a31914ee72@oldschoolsolutions.biz

Changes in v6:
- removed compatible for qcom,sm8550-pmic-glink" in pmic-glink
- fixed malformed gpu node
- Link to v5: https://lore.kernel.org/r/20250607-tb16-dt-v5-0-ae493364f525@oldschoolsolutions.biz

Changes in v5:
- removed patch for the CMN N160JCE-ELL panel, got reviewed
- re-ordered code in onboard_usb_dev as requested by Dmitry Baryshkov
- amended device tree with review notes from Dmitry Baryshkov where possible
  and resuting in a working laptop - added notes section
- Link to v4: https://lore.kernel.org/r/20250524-tb16-dt-v4-0-2c1e6018d3f0@oldschoolsolutions.biz

Changes in v4:
- squashed Makefile and dts commits to one
- picked up r-b from Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
- Link to v3: https://lore.kernel.org/r/20250524-tb16-dt-v3-0-17e26d935e73@oldschoolsolutions.biz

Changes in v3:
- removed changes in x1e80100.dtsi and x1p42100.dtsi - resolved with [2]
- fixed schema errors with correct compatible string for the model
- added power management for the camera via onboard_usb_dev.c
- amended node ordering
- changed the panel driver used to edp-panel, added panel in the driver
- amended x1e80100.dtsi for exposing PM8010: This one is not present in the design,
  added /delete-node/ for it.
- removed commented-out lines for sdhc, specified which don't work.
- corrected ZAP shader firmware name
- Link to v2: https://lore.kernel.org/r/20250516-tb16-dt-v2-0-7c4996d58ed6@oldschoolsolutions.biz

Changes in v2:
- removed nodes that gave DTC compile errors (pm8010_thermal, edp0_hpd_active)
- amended qcom.yaml
- shortened the commit titles to fit 75 chars
- Link to v1: https://lore.kernel.org/r/20250515-tb16-dt-v1-0-dc5846a25c48@oldschoolsolutions.biz

[2]: 20250520-topic-x1p4_tsens-v2-1-9687b789a4fb@oss.qualcomm.com
[3]: https://lore.kernel.org/all/20241203-x1e80100-va-mic-bias-v1-0-0dfd4d9b492c@linaro.org/
[4]: https://lore.kernel.org/all/20250814-x1e80100-add-edp-hpd-v1-0-a52804db53f6@linaro.org/

---
Jens Glathe (3):
      dt-bindings: arm: qcom: Add Lenovo TB16 support
      firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16
      arm64: dts: qcom: Add Lenovo ThinkBook 16 G7 QOY device tree

 Documentation/devicetree/bindings/arm/qcom.yaml    |    1 +
 arch/arm64/boot/dts/qcom/Makefile                  |    2 +
 .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1625 ++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |    1 +
 4 files changed, 1629 insertions(+)
---
base-commit: b1549501188cc9eba732c25b033df7a53ccc341f
change-id: 20250511-tb16-dt-e84c433d87b1
prerequisite-message-id: <20250701183625.1968246-1-alex.vinarskis@gmail.com>
prerequisite-patch-id: b35889814152fca77b3822bce5418358924fe9f7
prerequisite-change-id: 20250724-move-edp-endpoints-fadecdaadda1:v1
prerequisite-patch-id: c536bf9ec7fd22af9b05b695272997615dfd675f
prerequisite-patch-id: d513e5a08d3be585b9b6a737ef3a1ad275d7caad
prerequisite-patch-id: 605ef6f89dd84f810df11be9d11ee6803a6bf289
prerequisite-patch-id: 2ab2430624acbdd9011f6c0c2a77469fd19fc75a
prerequisite-patch-id: bfbb562513763ce75f2bb5da7f12e7b54ff3919d

Best regards,
-- 
Jens Glathe <jens.glathe@oldschoolsolutions.biz>

[PATCH v12 1/3] dt-bindings: arm: qcom: Add Lenovo TB16 support

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Document the x1p-42-100/x1-26-100 variants of the Thinkbook 16 G7 QOY.

[1]: https://psref.lenovo.com/syspool/Sys/PDF/ThinkBook/ThinkBook_16_G7_QOY/ThinkBook_16_G7_QOY_Spec.pdf

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 55e5eb75af8905c93e6604d54d516585f70a8e29..55113096dde567dddec419e67b916a0bff8c318e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1072,6 +1072,7 @@ properties:
       - items:
           - enum:
               - asus,zenbook-a14-ux3407qa
+              - lenovo,thinkbook-16
               - qcom,x1p42100-crd
           - const: qcom,x1p42100
 

-- 
2.48.1

[PATCH v12 2/3] firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Allow particular machine accessing eg. efivars.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/firmware/qcom/qcom_scm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index edeae6cdcf311228ae4b193cc37d0ce9414606ba..6a0184e49114e2e32a76490e90f3cc971dd6999a 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1999,6 +1999,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "hp,omnibook-x14" },
 	{ .compatible = "huawei,gaokun3" },
 	{ .compatible = "lenovo,flex-5g" },
+	{ .compatible = "lenovo,thinkbook-16" },
 	{ .compatible = "lenovo,thinkpad-t14s" },
 	{ .compatible = "lenovo,thinkpad-x13s", },
 	{ .compatible = "lenovo,yoga-slim7x" },

-- 
2.48.1

[PATCH v12 3/3] arm64: dts: qcom: Add Lenovo ThinkBook 16 G7 QOY device tree

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Device tree for the Lenovo Thinkbook 16 G7 QOY

The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].

Supported features:

- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera
- X1-45 GPU

Not supported yet:

- HDMI port.
- EC and some fn hotkeys.

Limited support yet:

- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.

This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1e device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).

Co-developed-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 arch/arm64/boot/dts/qcom/Makefile                  |    2 +
 .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1625 ++++++++++++++++++++
 2 files changed, 1627 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 94a84770b0802a9dc0c56ce6c59eea20967a5d89..4d449eb87a2076e41cb24e8e9fe183a4ac8fc52e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -331,3 +331,5 @@ x1p42100-asus-zenbook-a14-el2-dtbs	:= x1p42100-asus-zenbook-a14.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-asus-zenbook-a14.dtb x1p42100-asus-zenbook-a14-el2.dtb
 x1p42100-crd-el2-dtbs	:= x1p42100-crd.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-crd.dtb x1p42100-crd-el2.dtb
+x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
new file mode 100644
index 0000000000000000000000000000000000000000..1ac46cdc4386120ee18cd60380c1fcd10fbf472e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
@@ -0,0 +1,1625 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2024, Linaro Limited
+ * Copyright (c) 2025, Jens Glathe
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1p42100.dtsi"
+#include "x1e80100-pmics.dtsi"
+
+/delete-node/ &pmc8380_6;
+/delete-node/ &pmc8380_6_thermal;
+
+/ {
+	model = "Lenovo ThinkBook 16 Gen 7 QOY";
+	compatible = "lenovo,thinkbook-16", "qcom,x1p42100";
+	chassis-type = "laptop";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-0 = <&wcd_default>;
+		pinctrl-names = "default";
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pm8550_pwm 3 500000>;
+
+		power-supply = <&vreg_edp_bl>;
+	};
+
+	/*
+	 * This is an odd one. The camera is physically behind the eusb9 repeater (confirmed) but
+	 * if it is placed below the usb_2_dwc3 node, it will be switched off after ~30 seconds.
+	 * The reason seems to be that the dwc3 driver does not probe for child nodes when in
+	 * host-only mode. But that's the default setting for the xhci controllers due to issues
+	 * when in OTG mode. https://lore.kernel.org/all/20241210111444.26240-1-johan+linaro@kernel.org/
+	 * The whole reason it is described in the dt (as an USB device) is its requirement for
+	 * that additional regulator, and to get power management to switch it off when suspended.
+	 * Defining it stand-alone does work.
+	 */
+	camera {
+		compatible = "usb5986,1198";
+
+		vdd-supply = <&vreg_cam_5p0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>;
+
+		/* Display-adjacent port */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "host";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss0_sbu_mux>;
+					};
+				};
+			};
+		};
+
+		/* User-adjacent port */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "host";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss1_sbu_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E80100-LENOVO-ThinkBook-16";
+		audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS3",
+				"VA DMIC1", "MIC BIAS3",
+				"VA DMIC2", "MIC BIAS1",
+				"VA DMIC3", "MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	usb-1-ss0-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 167 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 168 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss0_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss0_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss0_sbu>;
+			};
+		};
+	};
+
+	usb-1-ss1-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 179 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss1_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss1_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss1_sbu>;
+			};
+		};
+	};
+
+	vreg_cam_5p0: regulator-cam-5p0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_CAM_5P0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VBL9";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_bl_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&misc_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p0: ldo5 {
+			regulator-name = "vreg_l5b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l16b_2p9: ldo16 {
+			regulator-name = "vreg_l16b_2p9";
+			regulator-min-microvolt = <2912000>;
+			regulator-max-microvolt = <2912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_1p0: ldo1 {
+			regulator-name = "vreg_l1f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_1p0: ldo2 {
+			regulator-name = "vreg_l2f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_1p0: ldo3 {
+			regulator-name = "vreg_l3f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1p42100/LENOVO/21NH/qcdxkmsucpurwa.mbn";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	pinctrl-0 = <&qup_i2c2_data_clk>, <&tpad_default>, <&kybd_default>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* ELAN06FA */
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* CIRQ1080 or SYNA2BA6 */
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* FTCS0038 */
+	touchpad@38 {
+		compatible = "hid-over-i2c";
+		reg = <0x38>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* GXTP5100 */
+	touchpad@5d {
+		compatible = "hid-over-i2c";
+		reg = <0x5d>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb5_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+	};
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb9_repeater: redriver@4b {
+		compatible = "nxp,ptn3222";
+		reg = <0x4b>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb9_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* ILIT2911 or GTCH1563 */
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l15b_1p8>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	pinctrl-0 = <&edp_hpd_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+
+			backlight = <&backlight>;
+
+			enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dp3_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+	remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_pwm {
+	status = "okay";
+};
+
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-disable;
+		output-enable;
+		drive-push-pull;
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&pmc8380_3_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		input-disable;
+		output-enable;
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio10";
+		function = "normal";
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1p42100/LENOVO/21NH/qcadsp8380.mbn",
+			"qcom/x1p42100/LENOVO/21NH/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1p42100/LENOVO/21NH/qccdsp8380.mbn",
+			"qcom/x1p42100/LENOVO/21NH/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l6b_1p8>;
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Speaker */
+	left_spkr: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Speaker */
+	right_spkr: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <34 2>, /* Unused */
+			       <72 2>; /* Secure EC I2C connection (?) */
+
+	edp_hpd_default: edp-hpd-default-state {
+		pins = "gpio119";
+		function = "edp0_hot";
+		bias-disable;
+	};
+
+	cam_reg_en: cam-reg-en-state {
+		pins = "gpio44";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb9_reset_n: eusb9-reset-n-state {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_card_det_n: sdc2-card-det-state {
+		pins = "gpio71";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts0_default: ts0-default-state {
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n-pins {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+
+	usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
+		oe-n-pins {
+			pins = "gpio167";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio168";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+	};
+
+	usb_1_ss1_sbu_default: usb-1-ss1-sbu-state {
+		oe-n-pins {
+			pins = "gpio178";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio179";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p8>;
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_1_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss1_ss_in>;
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	phys = <&usb_1_ss2_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&eusb5_repeater>;
+
+	status = "okay";
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb9_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};

-- 
2.48.1

Re: (subset) [PATCH v12 0/3] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[Bjorn Andersson]

On Fri, 22 Aug 2025 08:44:09 +0200, Jens Glathe wrote:
> Device tree for the Lenovo Thinkbook 16 G7 QOY
> 
> The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].
> 
> Supported features:
> 
> - USB type-c and type-a ports
> - Keyboard
> - Touchpad (all that are described in the dsdt)
> - Touchscreen (described in the dsdt, no known SKUss)
> - Display including PWM backlight control
> - PCIe devices
> - nvme
> - SDHC card reader
> - ath12k WCN7850 Wifi and Bluetooth
> - ADSP and CDSP
> - GPIO keys (Lid switch)
> - Sound via internal speakers / DMIC / USB / headphone jack
> - DP Altmode with 2 lanes (as all of these still do)
> - Integrated fingerprint reader (FPC)
> - Integrated UVC camera
> - X1-45 GPU
> 
> [...]

Applied, thanks!

[1/3] dt-bindings: arm: qcom: Add Lenovo TB16 support
      commit: 63727c59a917b6ffdb13d51c251727a3e21d38d9
[3/3] arm64: dts: qcom: Add Lenovo ThinkBook 16 G7 QOY device tree
      commit: d3f600dc452df45f0f404eba65a88f4aecc48b43

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>