[PATCH 1/6] arm64: dts: rockchip: move cpu_thermal node to the correct position

[Heiko Stuebner <heiko@sntech.de>]

The &cpu_thermal node was added at the wrong position, move it to
the correctly sorted one.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
 .../boot/dts/rockchip/rk3568-qnap-ts433.dts   | 96 +++++++++----------
 1 file changed, 48 insertions(+), 48 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index 6ae4316761c4..5656554ca284 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -196,6 +196,54 @@ &cpu3 {
 	cpu-supply = <&vdd_cpu>;
 };
 
+/*
+ * The MCU can provide system temperature too, but only by polling and of
+ * course also cannot set trip points. So attach to the cpu thermal-zone
+ * instead to control the fan.
+ */
+&cpu_thermal {
+	trips {
+		case_fan0: case-fan0 {
+			hysteresis = <2000>;
+			temperature = <35000>;
+			type = "active";
+		};
+
+		case_fan1: case-fan1 {
+			hysteresis = <2000>;
+			temperature = <45000>;
+			type = "active";
+		};
+
+		case_fan2: case-fan2 {
+			hysteresis = <2000>;
+			temperature = <65000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		/*
+		 * Always provide some air movement, due to small case
+		 * full of harddrives.
+		 */
+		map1 {
+			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+			trip = <&case_fan0>;
+		};
+
+		map2 {
+			cooling-device = <&fan 2 3>;
+			trip = <&case_fan1>;
+		};
+
+		map3 {
+			cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
+			trip = <&case_fan2>;
+		};
+	};
+};
+
 &gmac0 {
 	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
 	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
@@ -492,54 +540,6 @@ rgmii_phy0: ethernet-phy@3 {
 	};
 };
 
-/*
- * The MCU can provide system temperature too, but only by polling and of
- * course also cannot set trip points. So attach to the cpu thermal-zone
- * instead to control the fan.
- */
-&cpu_thermal {
-	trips {
-		case_fan0: case-fan0 {
-			hysteresis = <2000>;
-			temperature = <35000>;
-			type = "active";
-		};
-
-		case_fan1: case-fan1 {
-			hysteresis = <2000>;
-			temperature = <45000>;
-			type = "active";
-		};
-
-		case_fan2: case-fan2 {
-			hysteresis = <2000>;
-			temperature = <65000>;
-			type = "active";
-		};
-	};
-
-	cooling-maps {
-		/*
-		 * Always provide some air movement, due to small case
-		 * full of harddrives.
-		 */
-		map1 {
-			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
-			trip = <&case_fan0>;
-		};
-
-		map2 {
-			cooling-device = <&fan 2 3>;
-			trip = <&case_fan1>;
-		};
-
-		map3 {
-			cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
-			trip = <&case_fan2>;
-		};
-	};
-};
-
 &pcie30phy {
 	data-lanes = <1 2>;
 	status = "okay";
-- 
2.47.2