[PATCH 7/8] riscv: dts: spacemit: enable K1 SoC QSPI on BPI-F3

[Alex Elder <elder@riscstar.com>]

Define DTS nodes to enable support for QSPI on the K1 SoC, including
the pin control configuration used.  Enable QSPI on the Banana Pi
BPI-F3 board.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 .../boot/dts/spacemit/k1-bananapi-f3.dts      |  6 ++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi  | 21 +++++++++++++++++++
 arch/riscv/boot/dts/spacemit/k1.dtsi          | 16 ++++++++++++++
 3 files changed, 43 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index 33ca816bfd4b3..2f3750f7fd6f3 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -258,6 +258,12 @@ dldo7 {
 	};
 };
 
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_cfg>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
index 4eef81d583f3d..e922e05ff856d 100644
--- a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
@@ -73,6 +73,27 @@ i2c8-0-pins {
 		};
 	};
 
+	qspi_cfg: qspi-cfg {
+		qspi-pins {
+			pinmux = <K1_PADCONF(98, 0)>,    /* QSPI_DATA3 */
+				 <K1_PADCONF(99, 0)>,    /* QSPI_DATA2 */
+				 <K1_PADCONF(100, 0)>,   /* QSPI_DATA1 */
+				 <K1_PADCONF(101, 0)>,   /* QSPI_DATA0 */
+				 <K1_PADCONF(102, 0)>;   /* QSPI_CLK */
+
+			bias-disable;
+			drive-strength = <19>;
+			power-source = <3300>;
+		};
+
+		qspi-cs1-pins {
+			pinmux = <K1_PADCONF(103, 0)>;   /* QSPI_CS1 */
+			bias-pull-up = <0>;
+			drive-strength = <19>;
+			power-source = <3300>;
+		};
+	};
+
 	/omit-if-no-ref/
 	uart0_0_cfg: uart0-0-cfg {
 		uart0-0-pins {
diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
index af35f9cd64351..47f97105bff0b 100644
--- a/arch/riscv/boot/dts/spacemit/k1.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
@@ -823,6 +823,22 @@ uart9: serial@d4017800 {
 				status = "disabled";
 			};
 
+			qspi: spi@d420c000 {
+				compatible = "spacemit,k1-qspi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0 0xd420c000 0x0 0x1000>,
+				      <0x0 0xb8000000 0x0 0xc00000>;
+				reg-names = "QuadSPI", "QuadSPI-memory";
+				clocks = <&syscon_apmu CLK_QSPI_BUS>,
+					 <&syscon_apmu CLK_QSPI>;
+				clock-names = "qspi_en", "qspi";
+				resets = <&syscon_apmu RESET_QSPI>,
+					 <&syscon_apmu RESET_QSPI_BUS>;
+				interrupts = <117>;
+				status = "disabled";
+			};
+
 			/* sec_uart1: 0xf0612000, not available from Linux */
 		};
 
-- 
2.48.1