From: Conor Dooley <conor@kernel.org>
To: E Shattow <e@freeshell.de>
Cc: Emil Renner Berthing <kernel@esmil.dk>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Paul Walmsley <pjw@kernel.org>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Alexandre Ghiti <alex@ghiti.fr>,
linux-kernel@vger.kernel.org, linux-riscv@lists.infradead.org,
devicetree@vger.kernel.org, Icenowy Zheng <uwu@icenowy.me>,
Conor Dooley <conor+dt@kernel.org>
Subject: Re: [PATCH v3 2/2] riscv: dts: starfive: add Orange Pi RV
Date: Mon, 24 Nov 2025 11:07:35 +0000 [thread overview]
Message-ID: <20251124-blaming-duplicity-fb1311864b3f@spud> (raw)
In-Reply-To: <20251123225059.49665-3-e@freeshell.de>
[-- Attachment #1: Type: text/plain, Size: 3985 bytes --]
On Sun, Nov 23, 2025 at 02:50:45PM -0800, E Shattow wrote:
> From: Icenowy Zheng <uwu@icenowy.me>
>
> Orange Pi RV is a SBC based on the StarFive VisionFive 2 board.
>
> Orange Pi RV features:
>
> - StarFive JH7110 SoC
> - GbE port connected to JH7110 GMAC0 via YT8531 PHY
> - 4x USB ports via VL805 PCIe USB controller connected to JH7110 pcie0
> - M.2 M-key slot connected to JH7110 pcie1
> - HDMI video output
> - 3.5mm audio output
> - Ampak AP6256 SDIO Wi-Fi/Bluetooth module on mmc0
> - microSD slot on mmc1
> - SPI NOR flash memory
> - 24c02 EEPROM (read only by default)
>
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> Signed-off-by: E Shattow <e@freeshell.de>
> ---
> arch/riscv/boot/dts/starfive/Makefile | 1 +
> .../boot/dts/starfive/jh7110-orangepi-rv.dts | 76 +++++++++++++++++++
> 2 files changed, 77 insertions(+)
> create mode 100644 arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
>
> diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
> index 62b659f89ba7..d34c8c79bc10 100644
> --- a/arch/riscv/boot/dts/starfive/Makefile
> +++ b/arch/riscv/boot/dts/starfive/Makefile
> @@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-emmc.dtb
> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-lite.dtb
> +dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-orangepi-rv.dtb
> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
> new file mode 100644
> index 000000000000..16ec2767134e
> --- /dev/null
> +++ b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
> @@ -0,0 +1,76 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2025 Icenowy Zheng <uwu@icenowy.me>
> + */
> +
> +/dts-v1/;
> +#include "jh7110-common.dtsi"
> +
> +/ {
> + model = "Xunlong Orange Pi RV";
> + compatible = "xunlong,orangepi-rv", "starfive,jh7110";
> +
> + /* This regulator is always on by hardware */
> + reg_vcc3v3_pcie: regulator-vcc3v3-pcie {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3-pcie";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + wifi_pwrseq: wifi-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&sysgpio 62 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&gmac0 {
> + assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
> + assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
> + starfive,tx-use-rgmii-clk;
> + status = "okay";
> +};
> +
> +&mmc0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + cap-sd-highspeed;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + vmmc-supply = <®_vcc3v3_pcie>;
> + vqmmc-supply = <&vcc_3v3>;
> + status = "okay";
> +
> + ap6256: wifi@1 {
> + compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
> + reg = <1>;
> + /* TODO: out-of-band IRQ on GPIO21 */
What's up with this TODO? Why's the gpio not here? Missing binding
support, missing driver support?
> + };
> +};
> +
> +&mmc1 {
> + cd-gpios = <&sysgpio 41 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&pcie0 {
> + status = "okay";
> +};
> +
> +&pcie1 {
> + status = "okay";
> +};
> +
> +&phy0 {
> + rx-internal-delay-ps = <1500>;
> + tx-internal-delay-ps = <1500>;
> + motorcomm,rx-clk-drv-microamp = <3970>;
> + motorcomm,rx-data-drv-microamp = <2910>;
> + motorcomm,tx-clk-adj-enabled;
> + motorcomm,tx-clk-10-inverted;
> + motorcomm,tx-clk-100-inverted;
> + motorcomm,tx-clk-1000-inverted;
> +};
> +
> +&pwmdac {
> + status = "okay";
> +};
> --
> 2.50.0
>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
next prev parent reply other threads:[~2025-11-24 11:07 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-11-23 22:50 [PATCH v3 0/2] riscv: dts: starfive: Add OrangePi RV board E Shattow
2025-11-23 22:50 ` [PATCH v3 1/2] dt-bindings: riscv: starfive: add xunlong,orangepi-rv E Shattow
2025-11-24 7:28 ` Krzysztof Kozlowski
2025-11-24 13:22 ` Conor Dooley
2025-11-24 21:59 ` E Shattow
2025-11-25 7:28 ` Krzysztof Kozlowski
2025-11-25 7:33 ` Icenowy Zheng
2025-11-25 7:48 ` Krzysztof Kozlowski
2025-11-25 8:01 ` Icenowy Zheng
2025-11-25 13:07 ` E Shattow
2025-11-25 19:14 ` Conor Dooley
2025-11-26 20:34 ` E Shattow
2025-11-26 8:23 ` Krzysztof Kozlowski
2025-11-23 22:50 ` [PATCH v3 2/2] riscv: dts: starfive: add Orange Pi RV E Shattow
2025-11-24 11:07 ` Conor Dooley [this message]
2025-11-24 11:08 ` Icenowy Zheng
2025-11-24 13:21 ` Conor Dooley
2025-11-24 21:56 ` E Shattow
2025-11-25 22:24 ` [PATCH v3 0/2] riscv: dts: starfive: Add OrangePi RV board Conor Dooley
2025-11-26 13:48 ` Emil Renner Berthing
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251124-blaming-duplicity-fb1311864b3f@spud \
--to=conor@kernel.org \
--cc=alex@ghiti.fr \
--cc=aou@eecs.berkeley.edu \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=e@freeshell.de \
--cc=kernel@esmil.dk \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=pjw@kernel.org \
--cc=robh@kernel.org \
--cc=uwu@icenowy.me \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox