[PATCH v11 0/4] Add Qualcomm Technologies, Inc. Talos EVK SMARC support

[Sudarshan Shetty <tessolveupstream@gmail.com>]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=y, Size: 4929 bytes --]

Hi all,

This patch series adds device tree binding and board support for the
Qualcomm Technologies, Inc. Talos EVK SMARC platform based on the
QCS615 SoC.

The first patch introduces the DT binding entry for the Talos EVK
SMARC board, and the second patch adds the corresponding DTS
files for the platform.

Note:
USB(usb_1_dwc3) supports host-only mode based on the switch SW1 on
the SoM, which is purely a hardware controlled as USB-ID and USB-VBUS
is not connected the switching cannot be handled from SW.
Hence from SW Host-only mode is supported on Linux boot up.

Changes in v11:
 - Fixed inconsistent USB PHY node naming in qcs615-ride.dts to
   align with the expected naming convention. (suggested by
   yuanjiey)
 - Reordered properties in property-n and property-names for
   consistency across DT files.
 - Removed unnecessary output-low from the bt_en_state node.
 - Used a &label_reference for hdmi_connector.
 - Added pcieport0 device node, which is required for WLAN to
   power on.
 - No functional change in bindings file.

Changes in v10:
 - This series extends the gpio-backlight driver and its DT bindings
   to support multiple control GPIOs. (suggested by Dmitry)
 - Addressed DT node labeling feedback.
 - Polished overall device tree structure and minor formattings.
 - Corrected pinctrl configuration for the active-low PERST# pin.
 - Includes a fix for inconsistent USB PHY node naming in
   talos.dtsi. (suggested by Dmitry)
 - Enabled WiFi and Bluetooth functionality.
 - Updated commit message.
 - No functional change in bindings file.

Changes in v9:
 - The updates in the following patch url is taken care in this
   patch series.
   https://lists.freedesktop.org/archives/dri-devel/2025-November/534473.html
 - Ignore v8 patch

Changes in v8:
 - This patch series depends on the below url
   https://lists.freedesktop.org/archives/dri-devel/2025-November/534473.html
 - Moved the contents of `talos-evk-cb.dtsi` to `talos-evk.dtsi`
   which will describe all the standard configuration of the EVK.
 - Introduced 'talos-evk-lvds-auo,g133han01.dtso' which has overlay
   to disable HDMI and adds the LVDS-related on top of the base
   dts file. (suggested by Bjorn)
 - Ethernet and Wi-Fi/BT are not (yet) supported.
 - Updated commit message.
 - No functional change in bindings file.

Changes in v7:
 - Added i2c clock frequency for i2c5 node.
 - Moved adv7535 controller section to talos-evk.dts file.
 - Reorder the usb nodes.
 - GPI_DMA nodes added in the device tree files.
 - No functional change in bindings file.

Changes in v6:
 - Clarified description of `talos-evk-cb.dtsi` to explain that it
   defines common carrier board interfaces shared between HDMI and
   LVDS variants, And It’s a single carrier board. HDMI and LVDS
   share the same DSI interface, and only one can be active at a
   time depending on a DIP switch.
 - Added missing newlines before 'status' and between the last property
   and subnode (suggested by Konrad).
 - Updated commit messages for clarity.

Changes in v5:
 - Updated commit message. (suggested by Krzysztof)
 - Introduced generic node name for can, dp, hdmi-bridge. (suggested by
   Krzysztof)
 - Introduced talos-evk-cb.dtsi, which has common carrier board
   interfaces.
 - No functional change in bindings file.

Changes in v4:
 - Updated product name to full form per Krzysztof’s feedback in
   dt-binding comment.
 - Hook up the ADV7535 DSI-to-HDMI bridge to base DTS file.
 - Add DP connector node and MDSS DisplayPort controller.
 - Added USB note in the cover letter for maintainers' awareness.

Changes in v3:
 - Addressed comments from Dmitry regarding USB1 `dr_mode` and
   added a DTS comment.
 - No functional change in bindings file.

Changes in v2:
 - Renamed compatible to "qcom,talos-evk" (suggested by Dmitry/Bjorn)
 - Merged enum entry with existing `qcs615-ride` block (Krzysztof)
 - Fixed subject and commit message to use imperative mood.

Thanks,
Anusha

Sudarshan Shetty (4):
  dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform
  arm64: dts: qcom: talos: Fix inconsistent USB PHY node naming
  arm64: dts: qcom: qcs615-ride: Fix USB PHY label reference
  arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm64/boot/dts/qcom/Makefile             |   4 +
 arch/arm64/boot/dts/qcom/qcs615-ride.dts      |   2 +-
 .../qcom/talos-evk-lvds-auo,g133han01.dtso    | 126 ++++
 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi   | 616 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/talos-evk.dts        | 139 ++++
 arch/arm64/boot/dts/qcom/talos.dtsi           |   4 +-
 7 files changed, 889 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts

-- 
2.34.1