[PATCH v2 1/4] docs: iio: adxl345: fix typos and grammar

[Taha Ed-Dafili <0rayn.dev@gmail.com>]

Correct several grammatical errors, typos, and pluralization issues
throughout the ADXL345 documentation. Key changes include:
- Changing 'generic' to 'general-purpose'
- Correcting 'axis' to 'axes' in multiple tables and descriptions
- Improving phrasing in the device attributes section
- Fixing 'latent' to 'latency' in usage examples

Signed-off-by: Taha Ed-Dafili <0rayn.dev@gmail.com>
---
 Documentation/iio/adxl345.rst | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/Documentation/iio/adxl345.rst b/Documentation/iio/adxl345.rst
index bb19d64f67c3..41d209a4dccf 100644
--- a/Documentation/iio/adxl345.rst
+++ b/Documentation/iio/adxl345.rst
@@ -12,16 +12,16 @@ This driver supports Analog Device's ADXL345/375 on SPI/I2C bus.
 * `ADXL345 <https://www.analog.com/ADXL345>`_
 * `ADXL375 <https://www.analog.com/ADXL375>`_
 
-The ADXL345 is a generic purpose low power, 3-axis accelerometer with selectable
+The ADXL345 is a general-purpose, low-power, 3-axis accelerometer with selectable
 measurement ranges. The ADXL345 supports the ±2 g, ±4 g, ±8 g, and ±16 g ranges.
 
 2. Device Attributes
 ====================
 
-Each IIO device, has a device folder under ``/sys/bus/iio/devices/iio:deviceX``,
+Each IIO device has a device folder under ``/sys/bus/iio/devices/iio:deviceX``,
 where X is the IIO index of the device. Under these folders reside a set of
 device files, depending on the characteristics and features of the hardware
-device in questions. These files are consistently generalized and documented in
+device in question. These files are consistently generalized and documented in
 the IIO ABI documentation.
 
 The following table shows the ADXL345 related device files, found in the
@@ -42,7 +42,7 @@ specific device folder path ``/sys/bus/iio/devices/iio:deviceX``.
 +-------------------------------------------+----------------------------------------------------------+
 | in_accel_x_raw                            | Raw X-axis accelerometer channel value.                  |
 +-------------------------------------------+----------------------------------------------------------+
-| in_accel_y_calibbias                      | y-axis acceleration offset correction                    |
+| in_accel_y_calibbias                      | Y-axis acceleration offset correction                    |
 +-------------------------------------------+----------------------------------------------------------+
 | in_accel_y_raw                            | Raw Y-axis accelerometer channel value.                  |
 +-------------------------------------------+----------------------------------------------------------+
@@ -68,7 +68,7 @@ present, simply assume its value is 0.
 +-------------------------------------+---------------------------+
 | Channel type                        | Measurement unit          |
 +-------------------------------------+---------------------------+
-| Acceleration on X, Y, and Z axis    | Meters per second squared |
+| Acceleration on X, Y, and Z axes    | Meters per second squared |
 +-------------------------------------+---------------------------+
 
 Sensor Events
@@ -78,7 +78,7 @@ Specific IIO events are triggered by their corresponding interrupts. The sensor
 driver supports either none or a single active interrupt (INT) line, selectable
 from the two available options: INT1 or INT2. The active INT line should be
 specified in the device tree. If no INT line is configured, the sensor defaults
-to FIFO bypass mode, where event detection is disabled and only X, Y, and Z axis
+to FIFO bypass mode, where event detection is disabled and only X, Y, and Z axes
 measurements are available.
 
 The table below lists the ADXL345-related device files located in the
@@ -90,11 +90,11 @@ listed.
 +---------------------------------------------+---------------------------------------------+
 | Event handle                                | Description                                 |
 +---------------------------------------------+---------------------------------------------+
-| in_accel_gesture_doubletap_en               | Enable double tap detection on all axis     |
+| in_accel_gesture_doubletap_en               | Enable double tap detection on all axes     |
 +---------------------------------------------+---------------------------------------------+
 | in_accel_gesture_doubletap_reset_timeout    | Double tap window in [us]                   |
 +---------------------------------------------+---------------------------------------------+
-| in_accel_gesture_doubletap_tap2_min_delay   | Double tap latent in [us]                   |
+| in_accel_gesture_doubletap_tap2_min_delay   | Double tap latency in [us]                  |
 +---------------------------------------------+---------------------------------------------+
 | in_accel_gesture_singletap_timeout          | Single tap duration in [us]                 |
 +---------------------------------------------+---------------------------------------------+
@@ -118,9 +118,9 @@ listed.
 +---------------------------------------------+---------------------------------------------+
 | in_accel_x_gesture_singletap_en             | Enable single tap detection on X axis       |
 +---------------------------------------------+---------------------------------------------+
-| in_accel_x&y&z_mag_falling_en               | Enable inactivity detection on all axis     |
+| in_accel_x&y&z_mag_falling_en               | Enable inactivity detection on all axes     |
 +---------------------------------------------+---------------------------------------------+
-| in_accel_x&y&z_mag_adaptive_falling_en      | Enable AC coupled inactivity on all axis    |
+| in_accel_x&y&z_mag_adaptive_falling_en      | Enable AC coupled inactivity on all axes    |
 +---------------------------------------------+---------------------------------------------+
 | in_accel_y_gesture_singletap_en             | Enable single tap detection on Y axis       |
 +---------------------------------------------+---------------------------------------------+
@@ -330,7 +330,7 @@ Configure one or several events:
         ## doubletap, window [us]
         root:/sys/bus/iio/devices/iio:device0> echo 0.025 > ./events/in_accel_gesture_doubletap_reset_timeout
 
-        ## doubletap, latent [us]
+        ## doubletap, latency [us]
         root:/sys/bus/iio/devices/iio:device0> echo 0.025 > ./events/in_accel_gesture_doubletap_tap2_min_delay
 
         ## AC coupled activity, enable
-- 
2.47.3